• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.5
• /
• pp.1120-1128
• /
• 2004

In this paper, we has designed and implemented Up-converter for K-band with high IMD3 performance using balanced power amplifier. It is consisted of PA module and, Local Oscillator module with reject Filter, mixer module and If block, and Up-converter has a local loop path to decide whether it operate or not and has the sensing port to inspect output power level. According to the power budget of designed Up-converter, K-band balanced power amplifier was fabricated by commercial MMIC. Measurement results of up-converter show about 40dB Gain, PldB of 29dBm and OIP3 was 38.25dBm, that is good performance compared to power budgets. We has adjusted gate voltage of MMIC to control more than 30 dB gain. This up-converter was used in transceiver for PTP and PTMP, and applied to digital communication system that use QAM and QPSK modulation.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.5
• /
• pp.686-693
• /
• 2009

A 21- to 42-day feeding study was conducted in Ross male broilers to evaluate the use of dried bakery product (DBP) and the influence of adding fat at different points in the manufacturing process. Six dietary treatments were formulated using a factorial arrangement (3${\times}$2 design) with three levels of fat in the mixer (high: 4.8%, medium: 3.8% and low: 2.8%) with or without DBP (0 and 7%). Additional fat was sprayed on pellets in a post-pelleting liquid application to bring the fat content to a similar level in all diets. Data on pellet quality (before and after post-pelleting fat addition), broiler performance, nutrient digestibility and organ weights were studied. Pellets made with DBP showed higher hardness values when measured before post-pelleting fat addition (p<0.001), although DBP did not affect final pellet hardness or durability. Higher post-pelleting hardness and durability were shown by diets to which a lower level of fat had been added in the mixer (p<0.001). In general, post-pelleting fat application improved durability (p<0.05). However, broiler performance and ileal digestibility were not affected by any of the factors tested. Dietary treatments had a significant but variable effect on carcass yield (p<0.01), although there were no differences among treatments regarding breast and leg yield, abdominal fat or organ weights. The results indicate that up to 7% DBP could be used in the broiler diet without impairing performance, ileal digestibility or organ weights. The place or point of fat addition in the manufacturing process has a strong influence on pellet quality.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.11 s.353
• /
• pp.175-184
• /
• 2006

In this paper, we describe a 900MHz CMOS RF transceiver using an ISM band for ZigBee applications. The architecture of the designed rx front-end, which consists of a low noise amplifier, a down-mixer, a programmable gain amplifier and a band pass filter. And the tx front-end, which consists of a band pass filter, a programmable gain amplifier, an up-mixer and a drive amplifier. A low-if topology is adapted for transceiver architecture, and the total current consumption is reduced by using a low power topology. Entire transceiver is verified by means of post-layout simulation and is implemented in 0.18um RF CMOS technology. The fabricated chip demonstrate the measured results of -92dBm minimum rx input level and 0dBm maximum tx output level. Entire power consumption is 32mW(@1.8VDD). Die area is $2.3mm{\times}2.5mm$ including ESD protection diode pads.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.11
• /
• pp.1399-1406
• /
• 2011

The reducer of the mixer is one of the main parts of the processor used for water and wastewater treatment. In this study, an advanced reducer with a drywell structure was developed in order to prevent oil leakage during operation in the field. During the development of the advanced reducer prototype, a mockup, a metal mold, and a cast were made using CAD and a CNC machine. The structural safety of the reducer prototype's lower housing (drywell structure) was checked using the ALGOR commercial FEM analysis code, which yielded a von Mises stress of about 123 N/mm2, which is below the yield stress of 250 N/$mm^2$, and a natural frequency of about 650-700 Hz. In addition, the torque transmission efficiency for the advanced prototype was 95.87%, which is about 8% more than that found in a previous study, 88.45%, and the sound level was below 75 dB. Furthermore, no oil leakage or abnormal sound or vibration occurred. Therefore, an optimally designed advanced reducer prototype has been successfully developed.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.399-402
• /
• 2005

In this study, ethyl cellulose (EC)/montmorilloniote(MMT) nanocomposite films plasticized with environmental-friendly plasticizer (BET, EBN, ESO) were prepared by melt process using Hakke mixer. The $T_g$ of plasticized EC films decreased from 122 to $71^{circ}C$ with the increase in the BET content up to 30 $wt\%$. The addition of 10 $wt\%$ epoxidized soybean oil (ESO) as the second plasticizer cause the further drop of $T_g$ from 81 to $61^{circ}C$. The plasticizer-effect of BET was better than that of EBN. When the plasticizer was added into the EC films, the mechanical properties of EC films was decreased, however the addition of monotmorillonite (MMT) into the EC films or the ring opening reaction of ESO plasticizer cause enhancement of mechanical properties.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.1 no.1
• /
• pp.23-31
• /
• 1976

When Television signal of VHF and UHF channel is retransmitted at the relay system with 6MHz Bandwidth including video and aural signals, the image is often affected with the unnatural changes of output amplitude frequency response within ttle region of dual sideband near to the carrier frequency. These phenomena are caused by the unnecessary lower sideband due to the spurious emission at the local oscillator, the nonlinear distortion in the linear amplifier, the intermoudulation distortion with the components of neighboring signal, the AM-PM conversion, and the envelope delay distortion. From the output characteristics, considering above results, the chief cause is caused by nonlinear response and has an effect on the bias states. Finally, it is confirmed that the effects on neighboring signal appear high in case of Down conversion than Up conversion and obtained the method for reducing the effects on the system.

• Journal of the Korea Society of Computer and Information
• /
• v.7 no.4
• /
• pp.115-120
• /
• 2002

This paper presents the implementation of IS-95 CDMA signal processor, baseband and Intermediate Frequency(IF) digital converter using Field Programmable Gate Array(FPGA) and ADC/DAC and frequency up/down converter IS-95 CDMA channel processor is generated the pilot channel signal with short PN code and Walsh-code generator. The digital If is composed of FPGA. digital transmit/receive signal processor and high speed analog-to-digital converter(ADC) and digital-to-analog converter(DAC). The frequency up/down converter consisted of filter, mixer, digital attenuator and PLL is analog conversion between intermediate frequency(IF) and baseband. This implemented system can be deployed in the IS-95 CDMA base station device etc.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.4 s.316
• /
• pp.45-49
• /
• 2007

The isolation between transmitter and receiver has been a critical problem in a pulse-modulated RFID (Radio Frequency Identification) system where transmitter and receiver use the identical frequency. A method using a switch, a mixer, a BPF (band-pass filter), and an additional oscillator in the transmitter is proposed to improve the isolation between transmitter and receiver in an RFID system. The Proposed system up-converts the outgoing wave from a frequency different from the received signal and improves the isolation. The proposed method provided additional 20 dB improvement on the isolation.

• Elastomers and Composites
• /
• v.56 no.1
• /
• pp.6-11
• /
• 2021

In order to develop an ultra-high-density elastomeric material for substitution of steel dynamic dampers, a new curing system and technique for high-loading of the filler were examined in this study. Mechanochemical modification of chloroprene rubber (MAH-g-CR) using an internal mixer was carried out with maleic anhydride (MAH) as a reactive monomer. The optimum amount of MAH was 10 phr and the efficient grafting of MAH on CR could be achieved at a mixing temperature of 100℃. After preparing MAH-g-CR, 50 mol% epoxidized natural rubber (ENR 50) was blended with MAH-g-CR to develop a "self-curable rubber blend system" via reaction between the functional groups of the elastomeric matrices without the curing agent and additives. The content of ENR 50 was fixed at 30 wt.% throughout evaluation of the curing behavior of the MAH-g-CR/ENR blend. Tungsten powder was added to the MAH-g-CR/ENR matrix up to 60 vol.% to obtain ultra-high-density, and the maximum density obtained was 7.57 g/㎤. Stable ts2 (scorch time) and t90 (90% cure time) could be obtained even when tungsten powder was incorporated up to 60 vol.%. In addition, the tensile strength and damping properties of MAH-g-CR/ENR containing 60 vol.% of tungsten were better than those of CR containing 60 vol.% of tungsten.

• ETRI Journal
• /
• v.35 no.3
• /
• pp.386-396
• /
• 2013

A 10-Gbit/s wireless communication system operating at a carrier frequency of 300 GHz is presented. The modulation scheme is amplitude shift keying in incoherent mode with a high intermediate frequency (IF) of 30 GHz and a bandwidth of 20 GHz for transmitting a 10-Gbit/s baseband (BB) data signal. A single sideband transmission is implemented using a waveguide-tapered 270-GHz high-pass filter with a lower sideband rejection of around 60 dB. This paper presents an all-electronic design of a terahertz communication system, including the major modules of the BB and IF band as well as the RF modules. The wireless link shows that, aided by a clock and data recovery circuit, it can receive $2^7$-1 pseudorandom binary sequence data without error at up to 10 Gbit/s for over 1.2 m using collimating lenses, where the transmitted power is 10 ${\mu}W$.