• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1129-1133
• /
• 2001

An upper bound elemental technique(UBET) has been carried out to predict the forming load, the deformation pattern and the extruded length of the lateral extrusion of a spider for the automotive universal joint. For the upper bound analysis, a kinematically admissible velocity field(KAVF) is proposed. From the proposed velocity field, the upper bound load, the deformation pattern and the average length of the extruded billets are determined by minimizing the total energy consumption rate which is a function of unknown velocities at each element. Experiments are carried out with antimony-lead billets at room temperature using the rectangular shaped punch. The theoretical prediction of the forming load, the deformation pattern and the extruded length are good in agreement with the experimental results.

• 소음진동
• /
• 제10권4호
• /
• pp.596-601
• /
• 2000

Propeller shaft is one of the main excitation source in the vehicle driveline. This paper presents the correlation of the propeller shaft and axle vibration. 10 D.O.F. lumped mass model is constructed to simulate the dirveline. Experimental apparatus is constructed to verify the simulation model and to measure the vibration signal of lthe driveline. The results of simulation and experiments show that propeller shaft excitation is 2nd harmonic of the rotational frequency. Axle housing vibration signal shows that axle resonate with 2nd harmonic of excitation frequency due to universal joint effect.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1894-1899
• /
• 2000

The Roadway caused through Power Train engine vibration and bad ride comfort. It is very important to analyze the vibratory characteristics. The mathematical models on the Power Train, which is composed of engine-/transmission block, universal joint shaft, differential, rear axle arm and wheels, are developed and is verified by the experiments. This Paper describes the coupling influence occurred through a complete drive system for the power train. Dies study is carried out computationally with a calculation program and experimentally with the aid of the mode analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.193-196
• /
• 2002

This paper proposes the control problem of an inverted pendulum system based on Sugeno-Type of fuzzy logic. The universal approximating capability, learning ability, adaptation capability and disturbance rejection are collected in one control strategy. The proposed scheme does not require an accurate dynamic model and the joint acceleration measurement, yet it guarantees asymptotic trajectory tracking. Experimental results perform with an inverted pendulum to show the effectiveness of the approach.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.139-147
• /
• 2005

The lubricant impregnated MC nylon has good frictional properties, but its mechanical strength is inferior to steel for the mechanical elements. For the tribological application Nylon as gears, sliding bearings, cam and etc, the steel shafts are fitted in pre-heated nylon cylinder by a process of interference expansion fit and bonded by induction heating method. The joint shear strength of the two materials was measured by a universal test machine. From the study, the adhesive shear strength between these two materials was affected by the factors of the interference between nylon and steel, the size of nylon cylinder, knurl of steel shaft and inducting heating conditions. The most effective jointing conditions were analyzed and decided for the practical application in the industry.

• Transactions on Electrical and Electronic Materials
• /
• 제2권3호
• /
• pp.7-11
• /
• 2001

Utility boiler operators seeking to gain the greatest economic advantage from their units are faced with three challenges, namely the obligatory light-up fuel costs, the additional expense of supplementary fuel firing should they wish to use a cheaper fuel that may be beyond the original burner manufacturer’s stability and combustion performance assurances and the immediate environmental impact of both. The novel use of plasma arc technology can provide a solution to these challenges. This paper introduces the work being undertaken through a joint collaboration between the EU, Kazahkstan and Russia in order to develop a tried and tested engineering methodology and a mathematical based application and sensitivity analysis approach for the design and optimisation stage of these plasma devices that, as a consequence, their assist in their universal introduction.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2008년도 추계학술발표대회
• /
• pp.810-813
• /
• 2008

본 논문에서 연구하고 구현된 JTAG(Joint Test Action Group) Writer는 하나의 SoC(System On a Chip)만 지원하도록 설계된 기존 제품의 단점을 보완할 수 있도록 각 SoC의 제조 회사에서 제공하는 BSDL(Boundary Scan Description Language)을 이용하여 여러 가지 SoC에 쉽게 사용할 수 있도록 모듈화 했다. 그리고 기존 제품들이 사용하고 있는 직렬 포트나 병렬 포트 대신 안정적이고 편리한 USB(Universal Serial Bus) 접속규격을 지원하도록 개선했다.

• 대한견주관절학회:학술대회논문집
• /
• 대한견주관절학회 2008년도 제16차 학술대회
• /
• pp.164-164
• /
• 2008

The beach-chair traction position is designed to allow the use of traction while allowing the surgeon to orient the shoulder in an upright position and convert to an open procedure, if necessary. The patient is placed in the beach-chair position under general anesthesia. A three-point shoulder holder (Arthrex, Naples, Florida) is attached to the rail of the operating table on the same side as the surgeon, whereas it is placed on the side opposite the surgeon in the lateral decubitus position. A shoulder traction and rotation sleeve (Arthrex) are affixed to the arm following the manufacturer's instructions. Positioning the thumb toward the closed side of the sleeve ensures a field for the anterior portion of the rotator cuff and prevents the tendency of the suspension apparatus to place the arm in internal rotation. The arm is maintained in 30 to 40 degree abduction and 30 to 40 degree flexion by controlling the length and height of the bar and the location of the universal clamp. The universal clamp allows multiple planes of adjustment to control abduction and forward movement of the arm. The sleeve is attached to the longitudinal traction cable using a sterile hook, and a lateral strap is secured around the proximal portion of the sleeve to the overhead traction cable to ensure a field for glenohumeral reconstruction. The use of a lateral strap permits ideal shoulder positioning for improved access to the anterior and inferior glenohumeral joint. The lateral strap can be released or removed to widen the subacromial space during subacromial decompression or rotator cuff repair. A 10-lb weight is attached to the longitudinal traction cable for an average-sized person.

• 한국인터넷방송통신학회논문지
• /
• 제18권4호
• /
• pp.73-78
• /
• 2018

본 논문에서는 다중 소스가 분리 된 노드에서 암호화되고 각각의 공개 통신 채널을 통해 공동 싱크 노드로 전송되는 시스템을 고려한다. 우리는 상관 관계가 있는 암호화 키를 가진 것으로 알려진 기존 시스템의 보안 문제에 관심이 있다. 특히, 우리는 추가적인 비밀 키를 도입하지 않고 해결책을 찾는데 초점을 맞추고 비용을 최소화하고 이미 실행중인 시스템을 중단시키는 위험을 최소화하기 위해 최소한의 수정만으로. 우리는 도청자가 이용 가능한 공개 통신 채널에 액세스함으로써 모든 암호문, 즉 암호화 된 소스를 획득하는 보안 모델 하에서의 해결책을 제안한다. 우리의 주요 기술은 암호문을 공개 통신 채널에 보내기 전에 특정 선형 코드의 유니버셜 함수를 사용하여 암호문을 인코딩하는 것이다.

• PNF and Movement
• /
• 제21권2호
• /
• pp.171-183
• /
• 2023

Purpose: The purpose of this study was to compare universal goniometry (UG), which is commonly used in clinical practice to measure the range of motion (ROM) of finger joints with a wearable soft sensor glove, and to analyze the reliability to determine its usefulness. Methods: Ten healthy adults (6 males, 4 females) participated in this study. The metacarpophalangeal joint (MCP), interphalangeal joint (IP), and proximal interphalangeal joint (PIP) of both hands were measured using UG and Mollisen HAND soft sensor gloves during active flexion, according to the American Society for Hand Therapists' measurement criteria. Measurements were taken in triplicate and averaged. The mean and standard deviation of the two methods were calculated, and the 95% limits of agreement (LOA) of the measurements were calculated using the intraclass correlation coefficient (ICC) and Bland-Altman plot to examine the reliability and discrepancies between the measurements. Results: The results of the mean values of the flexion angles for the active range of motion (AROM) of the finger joints showed large angular differences in the finger joints, except for the MCP of the thumb. In the inter-rater reliability analysis according to the measurement method, the ICC (2, 1) value showed a low level close to 0, and the mean difference by the Bland-Altman plot showed a value greater than 0, showing a pattern of discrepancy. The 95% LOA had a wide range of differences. Conclusion: This study is a preliminary study investigating the usefulness of the soft sensor glove, and the reliability analysis showed a low level of reliability and inconsistency. However, if future studies can overcome the limitations of this study and the technical problems of the soft sensor glove in the development stage, it is suggested that the measurement instrument can show more accurate measurement and higher reliability when measuring ROM with UG.