• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 F
• /
• pp.2553-2555
• /
• 1999

The paper contains design formulas and an execution algorithm for calculation of distributed parameters as well as wave and impedance parameters of a uniform transmission line using data of the line input impedance measurements by the OPEN-SHORT method. In difference from published before works on the OPEN-SHORT method application for line parameters determination, in which the lines with small losses are considered /1-3/, the obtained formulas allow to calculate parameters of transmission lines with arbitrary losses. It opens new possibilities of the OPEN-SHORT method utilization for development and application of the probe - type lossy dielectric media parameters meters based on transmission lines, including probe-type moisture material meters.

• Journal of electromagnetic engineering and science
• /
• 제19권1호
• /
• pp.42-47
• /
• 2019

This paper introduces a modified Wilkinson power divider that uses uniform transmission lines for various terminated impedances and an arbitrary power ratio. For the designed power ratio, the proposed divider changes only the electrical lengths of the transmission lines between the input and output ports, and those between the output ports and the isolation resistor. In this case, even when various termination impedances of the ports exist, the divider characteristics are satisfied. To verify the feasibility of the proposed divider, two circuits were designed to operate at a frequency of 2 GHz with 2:1 and 4:1 power splitting ratios and various terminated impedances of 40, 70, and $60{\Omega}$ for one circuit, and 50, 70, and $60{\Omega}$ for the other. The measurement and simulation results were in good agreement.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권4호
• /
• pp.463-470
• /
• 2014

A Verilog model is proposed for transmission lines to perform the all-Verilog simulation of high-speed chip-to-chip interface system, which reduces the simulation time by around 770 times compared to the mixed-mode simulation. The single-pulse response of transmission line in SPICE model is converted into that in Verilog model by converting the full-scale analog signal into an 11-bit digital code after uniform time sampling. The receiver waveform of transmission line is calculated by adding or subtracting the single-pulse response in Verilog model depending on the transmitting digital code values with appropriate time delay. The application of this work to a USB 2.0 high-speed PHY interface reduces the simulation time to less than three minutes with error less than 5% while the mixed-mode simulation takes more than two days for the same circuit.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 E
• /
• pp.2143-2145
• /
• 1999

Measurements of wind noise, generated by High-voltage overhead transmission lines placed in a uniform flow are carried out in the Anechoic windtunnel. High-voltage overhead transmission lines generates audible wind noise, which cause a serious environment problem. Accordingly, wind noise has become one of major concerns for design engineers and operations personnel. In the present research, tests were mainly performed with various configuration of transmission line with spiral wires. Remarkable noise reduction was observed for some of the spiral transmission lines, compared with the noise generated without the spiral wire.

• 한국전자파학회논문지
• /
• 제19권11호
• /
• pp.1223-1232
• /
• 2008

본 논문에서는 비공진형 협벽 도파관 슬롯 배열 설계를 위해 필요한 기준이 되는 단위 슬롯 어드미턴스를 해석적으로 추출하는 방법을 제시하였다. 충분한 개수의 동일 기울임 각을 가지는 교번 슬롯 구조에 대해, 도파관 협벽의 단위 슬롯과 단위 슬롯 양쪽에 이웃한 전송선 부분을 균일한 손실 전송선으로 근사하고, 이로부터 손쉽게 전체의 ABCD 행렬을 계산하여 전체의 시뮬레이션 또는 측정값과 비교함으로써, 손실 전송선의 복소 특성 임피던스와 복소 전파 상수를 구하고 해석 적으로 정규화 된 슬롯 어드미턴스를 추출하였다. 제안한 방법의 타당성을 입증하기 위해, 대역 협벽 도파관 슬롯 배열 설계용으로 제작된 기준 슬롯 도파관 샘플의 정규화 된 슬롯 어드미턴스를 구하고 기존의 방법으로 얻은 값과 비교하여 잘 일치함을 보였다.

• Journal of Magnetics
• /
• 제20권4호
• /
• pp.460-465
• /
• 2015

The paper presents methodologies and results concerning one- and two-dimensional numerical modeling of radio frequency oscillations in a coaxial transmission line fed with a short pulse of electric current. The line is partially filled with a ferrite material, magnetized longitudinally close to saturation. The 2D model has permitted analyzing, for the first time in the art, the spatial structure and dynamics of the wave field within the radially non-uniform cross-section planes of the non-linear and dispersive guiding structure. This opens ways for optimizing size parameters of the line and the extent to which it is filled with the ferromagnetic material, thus increasing the line's electric strength and intensity of the r.f. oscillations.

• 한국의류학회지
• /
• 제46권2호
• /
• pp.367-374
• /
• 2022

Herein, a highly elastic e-textile band with a two-wire transmission line was designed and fabricated for smart clothing applications. A conductive yarn with a very uniform low electrical resistance of 0.0357 Ω/cm was developed and used for the signal and ground lines. To control the elasticity of the e-textile band, spandex yarns were added in the warp direction during knitting and the tension was adjusted. As the length of the e-textile band increased, its RF performance deteriorated. Furthermore, the frequency corresponding to -3 dB S21 was lower in the 30% stretched band than in the unstretched band. For the e-textile bands with lengths 10, 50, and 100 cm, the frequencies corresponding to -3 dB S21 were 107.77, 24.56, and 13.02 MHz when not stretched, and 88.74, 22.02, and 12.60 MHz when stretched by 30%. The fabricated bands were flatter, more flexible, and more elastic than transmission line cables; thus, they can be easily integrated into wearables and smart clothing. However, to increase RF performance and achieve optimum utilization, future studies must focus on the fabrication of transmission lines with lower resistance and reduced distance between the signal and ground lines, and thus the number of transmission lines can be increased.

• Journal of Electrical Engineering and Technology
• /
• 제9권6호
• /
• pp.2049-2057
• /
• 2014

In this paper, a numerical method for analyzing coupling between high-altitude electromagnetic pulse (HEMP) as external field and a shielded twisted pair (STP) cable is proposed, which is based on an expanded chain matrix. Load responses of electromagnetic (EM) field excitation in uniform transmission line (TL) are solved by Baum-Liu-Tesche (BLT) equations in frequency domain, however, it is difficult to apply BLT equations to solve load responses of STP cable because the iteratively changing configuration of each twisted pairs are involved in cable. To avoid this problem and decrease memory and CPU time, we proposed the expanded chain matrix modeling method that is calculated using ABCD parameters, and applied multi-conductor transmission line (MTL) theory to consider the EMP coupling effectiveness of each twisted pairs. The results implemented by the proposed method are presented and compared with those obtained by the finite-difference time domain (FDTD) method as a kind of 3D full wave analysis.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제9권1호
• /
• pp.8-13
• /
• 2009

In this paper, discontinuous interconnect lines are modeled as a cascaded line composed of many uniform interconnect lines. The system functions of respective uniform interconnect lines are determined, followed by its time domain response. Since the time domain response expression is a transcendental form, the waveform expression is reconfigured as an approximated linear expression. The proposed model has less than 2% error in the delay estimation.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권1호
• /
• pp.40-44
• /
• 2006

In this paper, the distortion characteristics of an electrical pulse which has a rise/fall time due to the dispersion and the reflection, on nonuniform tapered microstrip lines has investigated in time domain. The transmission characteristics on uniform microstrip lines in time domain had represented already, but the results for the nonuniform tapered microstrip lines not represented yet. We investigated the transmission characteristics for pulse signal on the nonuniform tapered microstrip lines, and the result applied to design of wide band impedance matching circuit in design of MMIC. The voltage and current transfer functions are shown for the tapered line. The dispersion and distortion obtained by using these transfer functions are represented for the nonideal square pulse.