• Journal of the Korean Geosynthetics Society
• /
• v.13 no.2
• /
• pp.1-10
• /
• 2014

In this study, two different types of dredged fill injection methods are introduced and filling experiments were conducted to analyze the impact of each technique to the distribution and deposition of dredged soil fill and how it influence the final tube shape. Two transparent plastic tubes were fabricated to observe the deposition behavior of the deposited fill material. Both tubes measured 4.0 meters in length (L) and has vinyl tube diameters (D) of 0.5m and 0.7m. T-type and I-type inlet system are also introduced in this paper. The influence of this inlet systems to the distribution and deposition behavior of dredged soil fill inside the vinyl tubes were observed during the experiment. After the sedimentation of the slurry mixture, the water on top of the soil sediments are removed and the slurry mixture was re-injected into the vinyl tube, this process was carried out repeatedly. The shape changes of the vinyl tube, e.g. the changes in both tube height and width, are constantly monitored after each slurry injection and water draining phases. Crater formation was observed in the case of I-Type inlet system and a non-uniform sediment distribution occurred. For the diffusion deposit of soil particles to long distance are minimal shape technique using the T-Type inlet system. Therefore the undrain filling height ratio ($H/D_0$) was found to be around 0.54 to 0.64 and the horizontal strain ratio ($W/D_0$) ranges from 1.45 to 1.54. The filling soil height is proportional to dredged-material filling phases, but, horizontal strain ratio is constant or inversely reduced so that the center of tube body is raised in the upward direction.

• Journal of the Korean Vacuum Society
• /
• v.17 no.6
• /
• pp.528-537
• /
• 2008

60 nm and 20 nm thick hydrogenated amorphous silicon(a-Si:H) layers were deposited on 200 nm $SiO_2$/single-Si substrates by inductively coupled plasma chemical vapor deposition(ICP-CVD). Subsequently, 30 nm-Ni layers were deposited by an e-beam evaporator. Finally, 30 nm-Ni/(60 nm and 20 nm) a-Si:H/200 nm-$SiO_2$/single-Si structures were prepared. The prepared samples were annealed by rapid thermal annealing(RTA) from $200^{\circ}C$ to $500^{\circ}C$ in $50^{\circ}C$ increments for 40 sec. A four-point tester, high resolution X-ray diffraction(HRXRD), field emission scanning electron microscopy(FE-SEM), transmission electron microscopy(TEM), and scanning probe microscopy(SPM) were used to examine the sheet resistance, phase transformation, in-plane microstructure, cross-sectional microstructure, and surface roughness, respectively. The nickel silicide from the 60 nm a-Si:H substrate showed low sheet resistance from $400^{\circ}C$ which is compatible for low temperature processing. The nickel silicide from 20 nm a-Si:H substrate showed low resistance from $300^{\circ}C$. Through HRXRD analysis, the phase transformation occurred with silicidation temperature without a-Si:H layer thickness dependence. With the result of FE-SEM and TEM, the nickel silicides from 60 nm a-Si:H substrate showed the microstructure of 60 nm-thick silicide layers with the residual silicon regime, while the ones from 20 nm a-Si:H formed 20 nm-thick uniform silicide layers. In case of SPM, the RMS value of nickel silicide layers increased as the silicidation temperature increased. Especially, the nickel silicide from 20 nm a-Si:H substrate showed the lowest RMS value of 0.75 at $300^{\circ}C$.

• Journal of the Korean Vacuum Society
• /
• v.17 no.6
• /
• pp.538-543
• /
• 2008

Recently a nano-scale diamond is possible to manufacture forms of powder(below 100 nm) by new processing of explosion or deposition method. Using a sintering of nano-scale diamond is possible to manufacture of grinding tools. We have need of a processing development of coated uniformly inorganic to prevent an abnormal grain growth of nano-crystal and bonding obstacle caused by sintering process. This paper, in order to improve the sintering property of nano-scale diamond, we coated ZnO thin films(thickness: $20{\sim}30\;nm$) in a vacuum by ALD(atomic layer deposition) Economically, in order to deposit ZnO all over the surface of nano-scale diamond powder, we used a new modified fluidized bed processing replaced mechanical vibration effect or fluidized bed reactor which utilized diamond floating owing to pressure of pulse(or purge) processing after inserted diamond powders in quartz tube(L: 20 mm) then closed quartz tube by porosity glass filter. We deposited ZnO thin films by ALD in closed both sides of quartz tube by porosity glass filter by ALD(precursor: DEZn($C_4H_{10}Zn$), reaction gas: $H_2O$) at $10^{\circ}C$(in canister). Processing procedure and injection time of reaction materials set up DEZn pulse-0.1 sec, DEZn purge-20 sec, $H_2O$ pulse-0.1 sec, $H_2O$ purge-40 sec and we put in operation repetitive 100 cycles(1 cycle is 4 steps) We confirmed microstructure of diamond powder and diamond powder doped ZnO thin film by TEM(transmission electron microscope) Through TEM analysis, we confirmed that diamond powder diameter was some $70{\sim}120\;nm$ and shape was tetragonal, hexagonal, etc before ALD. We confirmed that diameter of diamond powders doped ZnO thin film was some $70{\sim}120\;nm$ and uniform ZnO(thickness: $20{\sim}30\;nm$) thin film was successfully deposited on diamond powder surface according to brightness difference between diamond powder and ZnO.

• Childhood Kidney Diseases
• /
• v.14 no.1
• /
• pp.22-31
• /
• 2010

Purpose : This study was performed to evaluate the relationship between glomerular basement membrane (GBM) alterations to epithelial cell (EpC) structure and renal function in Alport Syndrome (AS) patients. Methods : Fifteen patients diagnosed with AS (4-26yrs) were examined. The GBM in AS was categorized as : C1) normal, C2) minor alterations (widening of lamina rara interna or externa without lamina densa change), C3) nonspecific splitting of lamina densa, C4) basket-weaving pattern of lamina densa splitting. The length of each GBM portion along the epithelial side was measured on the systematically obtained electron microscopic photographs. Furthermore to obtain an objective assessment of the degree of glomerular EpC foot process change, the number of slit pores along $10\;{\mu}m$ of peripheral GBM in each category was obtained. Results : The percentage of normal GBM portion (C1) correlated inversely with daily protein excretion (g/day/$m^2$, P<0.05) and sum of the percentage of abnormal GBM portion (C2+C3+C4) had direct correlation with daily protein excretion (g/day/$m^2$, P<0.05). There were no significant relationships between the percentages of other categories of GBM alterations and creatinine clearance or protein excretion. There were no significant relationships between of creatinine clearance in relation to normal GBM(C1) portion as well as that in relation to sum of the percentage of abnormal GBM portion (C2+C3+C4). GBM abnormality did not correlate with age at biopsy. Conclusion : The extent of GBM structural abnormality is related to proteinuria in AS but the epithelial response is uniform even though the GBM ultrastructural lesions are not.

• The Korean Journal of Nuclear Medicine
• /
• v.39 no.1
• /
• pp.57-68
• /
• 2005

Purpose: The objective of this study was to assess attenuation correction algorithms with the $^{137}Cs$ point source for the brain positron omission tomography (PET) imaging process. Materials & Methods: Four different types of phantoms were used in this study for testing various types of the attenuation correction techniques. Transmission data of a $^{137}Cs$ point source were acquired after infusing the emission source into phantoms and then the emission data were subsequently acquired in 3D acquisition mode. Scatter corrections were performed with a background tail-fitting algorithm. Emission data were then reconstructed using iterative reconstruction method with a measured (MAC), elliptical (ELAC), segmented (SAC) and remapping (RAC) attenuation correction, respectively. Reconstructed images were then both qualitatively and quantitatively assessed. In addition, reconstructed images of a normal subject were assessed by nuclear medicine physicians. Subtracted images were also compared. Results: ELEC, SAC, and RAC provided a uniform phantom image with less noise for a cylindrical phantom. In contrast, a decrease in intensity at the central portion of the attenuation map was noticed at the result of the MAC. Reconstructed images of Jaszack and Hoffan phantoms presented better quality with RAC and SAC. The attenuation of a skull on images of the normal subject was clearly noticed and the attenuation correction without considering the attenuation of the skull resulted in artificial defects on images of the brain. Conclusion: the complicated and improved attenuation correction methods were needed to obtain the better accuracy of the quantitative brain PET images.

• Asian Journal of Turfgrass Science
• /
• v.23 no.2
• /
• pp.331-344
• /
• 2009

Buffalograss is an important turfgrass species with excellent cold, heat, and drought tolerance. Understanding the physiological integration of buffalograss under heterogeneous conditions helps to develop cultural practices that better use limited resources for uniform turf quality. The objective of this study was to evaluate physiological integration of buffalograss under water deficit stress and the involvement of lipid peroxidation and antioxidants in the process. In one experiment, buffalograss was planted in the center of a four-compartment growth unit. Watering frequencies, once a week(+) and once in two weeks(-), were combined with the sand(S) or peat(P) in each unit to generate five total treatments(P+S-P-S+, P+P+P+P+, S-S-S-S-, P-P-P-P-, and S+S+S+S+). The average number of shoot established from the heterogeneous root-zone medium was higher than the average of four possible homogeneous media. In second experiment, single ramet in Hoagland solution($S_0$) or single ramet in Hoagland solution with 20% PEG-6000($S_s$) were compared with two connectedramets under different treatments. Treatments for connected ramets were young ramet in Hoagland solution($Y_{os}$) and old ramet in Hoagland solution with 20% PEG-6000($O_{os}$), and old ramet in Hoagland solution($O_{ys}$) and young ramet in Hoagland solution with 20% PEG-6000($Y_{ys}$). Lipid peroxidation, antioxidants, and proline showedphysiological integration between ramets subjected to different levels of water stress. Superoxide dismutase(SOD), Guaiacol peroxidase(G-POD), malondialdehyde(MDA), and free proline also showed different time courses and relative activities during the physiological integration.

• Food Engineering Progress
• /
• v.14 no.3
• /
• pp.193-201
• /
• 2010

The aim of this study was to analyse the quality of Yukwa puffed by using a vacuum puffing machine and compare to deep-fried Yukwa. The effect of vacuum puffing condition including heating temperature(100-${160^{\circ}C}$), preheating time(0-8 min) and vacuum puffing time(5-20 min) on physical and microstructure characteristics of the Yukwa was investigated. Vacuum puffed Yukwa at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 10 min puffing time had highest value in volumetric expansion ratio(10.04) and lowest value in bulk density(0.15 g/$cm^{3}$). The breaking strength showed the lowest value of 140 g/$cm^{3}$ in vacuum puffing Yukwa at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 15 min puffing time. The Yukwa puffed with the vacuum puffing machine at ${100^{\circ}C}$ heating temperature, 6 min preheating time and 15 min puffing time had the higher value of bulk density and the lower value of volumetric expansion ratio than those of deep-fried Yukwa. Increasing preheating time and vacuum puffing time caused an increase in white and an decrease in yellowness. The vacuum-puffed Yukwa exhibited smaller and uniform cell structure, while deep-fried Yukwa exhibited apparently in larger pores inside and smaller pores near the surface layer. The optimum condition of vacuum puffing machine for the production of vacuum-puffing Yukwa was ${120^{\circ}C}$ heating temperature, 4 min preheating time and 5 min puffing time.

• Journal of Korea Water Resources Association
• /
• v.54 no.8
• /
• pp.629-641
• /
• 2021

In this study, a two-dimensional numerical model (Nays2DH) was applied to analyze the process of morphological changes in the river channel bed depending on the changes in the amount of flooding after fully opening the Sejong weir, which was constructed upstream of the Geum River. For this, numerical simulations were performed by assuming the flow conditions, such as a non-uniform flow (NF), unsteady flows (single flood event, SF), and a continuous flood event (CF). Here, in the cases of the SF and CF, the normalized hydrograph was calculated from real flood events, and then the hydrograph was reconfigured by the peak flow discharge according to the scenario, and then it was employed as the flow discharge at the upstream boundary condition. In this study, to quantitatively evaluate the morphological changes, we analyzed the time changes in the bed deformation the bed relief index (BRI), and we compared the aerial photographs of the study area and the numerical simulation results. As simulation results of the NF, when the steady flow discharge increases, the ratio of lower width to depth decreases and the speed of bar migration increases. The BRI initially increases, but the amount of change decreased with time. In addition, when the steady flow discharge increases, the BRI increased. In the case of SF, the speed of bar migration decreased with the change of the flow discharge. In terms of the morphological response to the peak flood discharge, the time lag also indicated. In other words, in the SF, the change of channel bed indicates a phase lag with respect to the hydraulic condition. In the result of numerical simulation of CF, the speed of bar migration depending on the peak flood discharges decreased exponentially despite the repeated flood occurrences. In addition, as in the result of SF, the phase lag indicated, and the speed of bar migration decreased exponentially. The BRI increased with time changes, but the rate of increase in the BRI was modest despite the continuous peak flooding. Through this study, the morphological changes based on the hydrological characteristics of the river were analyzed numerically, and the methodology suggested that a quantitative prediction for the river bed change according to the flow characteristic can be applied to the field.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.40 no.4
• /
• pp.15-31
• /
• 2022

This study interpreted the logical validity of the landscape restoration and maintenance patterns of Changgyeonggung Palace, where modern landscapes coexist. The results of the study are as follows; First, the changes in the landscape restoration and maintenance attitude concerning the Changgyeonggung management organization were identified. With the establishment of the Office of the Imperial Garden, an imperial property was nationalized. The Cultural Heritage Managing Department was opened in 1961, and Changgyeonggung Palace were preserved as designated as historical sites in 1963. An environmental purification was implemented by the Changgyeonggung Office as a follow-up measure for restoration in 1983. As the Cultural Heritage Administration promoted in 1999 and the Royal Palaces and Tombs Center was established in 2019, the palace has been managed professionally as a palace landscape to provide a viewing environment. Second, In the 'Purification Period of Changgyeongwon(1954~1977)', environmental purification was carried out to restore amusement facilities, install facilities for cherry blossom viewing, and develop the place into a national zoo. In the 'Reconstruction Period of Changgyeonggung(1983~1986)', restoring function as an urban park, reserving green areas, the outside space was recreated in the traditional feel, and the forest area was generally maintained. In the 'Supplementation Period of Traditional Landscape Architecture Space(1987~2009)', a uniform green landscape was created with pine trees and various vegetation landscapes centered on the flower beds. In the 'Improvement and Maintenance Period of Viewing Environment(2010~2022), a master plan was reestablished on the premise of utilization, but maintenance has been carried out in a small scale centering on unit space. Third, regarding the validity of the landscape restoration and maintenance, It was found in terms of 'originality' that the recovery of the palace system has not been expanded for over 40 years in existing areas. The 'characteristics of the times', which shows whether multi-layered history was taken into account, Changgyeongwon was excluded from the discussion in the process of setting the base year twice. In terms of 'integrity,' the area of the Grand Greenhouse where the historic states coexists needs a maintenance policy that binds the greenhouse, carpet flower bed, and Chundangji Pond. The 'utility' identified as the utilization of spaces suggests the establishment of a sense of place in the Grand Greenhouse area, which is concentrated with programs different from other areas.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.1
• /
• pp.142-160
• /
• 2023

The position of the people who participated in the Bapyo Ritual held in the reign of King Sejong and the corresponding costumes were examined. The king, who was the executive body of the ritual, wore Myeon-Bok, a court dress, and Myeon-Bok was Gujang-Bok made of Jang-wha on Guryu-Pyeongcheongwan. Crown princes, royal families, and government officials wore Oryang-Gwan and Jekraeui, which were Jobok. The crown princes' Joboks were changed from Oryang-Gwan to Wukryang-Gwan in the dynasty year 10 of King Sejong, and in the year of King Munjong's accession, Myeon-Bok was received, and after King Danjong, the crown princes wore Palryu-Pyeongcheongwan and Chiljang-Bok. Diplomats and Jongsagwan who were the envoys wore Sangbok. A Sangbok worn by the diplomat was Samo with Danryeong, Seo-Dae, and Hyeopgeum-Hwa, and a Sangbok worn by Jongsagwan was Samo, Danryeong, Heukgak-Dae, and Heukpi-Hwa. Byulgam, who served as an attendant to the king in the king's close quarters, wore Gongbok and Sangbok. Gongbok consisted of Ja-Geon, Danryeong and Heukpi-Hwa, and Sangbok consisted of orange color Cho-Rip, Jikryeong, Joa, and Heukpi-Hwa. The person holding San, Gae , Sujeongjang, and Geumwolbu wore Ja-Geon and Cheong-Ui, and Seon wore Pimoja and Hong-Ui. Siwigun wore armor and helmets equipped with weapons. Among court musicians, Aksa's costumes consisted of Bokdu, Bigongbok, Geumdonghyeokdae, Bibaekdaedae, and Opiri, and Aksaeng's one composed of Gaechaek, Bisuransam, Hyupgo, Mal, Maldae, and Opiri. As a result of the above, the process of ceremonial clothes becoming uniform clothes in the reign of King Sejong was confirmed. The king and lower-ranking officials such as crown princes, government officials, diplomats, Byulgam, armies for ceremonial weaponry, and court musicians participating in the Bapyo Ritual wore the highest grade of ceremonial clothes for each class. King Sejong had repeated discussions to build a nation based on Confucianism, and arranged each rite and corresponding costume, and the Bapyo Ritual costume was also systematically prepared for each position. The ceremonial clothing organized during the reign of King Sejong was regulated in Yejon and became the basis for continuing to the late Joseon Dynasty.