• Structural Engineering and Mechanics
• /
• v.88 no.1
• /
• pp.25-42
• /
• 2023

This paper presents a finite element (FE) simulation of eccentrically loaded lightweight aggregate concrete-encased steel (LACES) columns with H-shaped steel sections, analytical equations are also established to estimate the columns' axial and bending moment interaction capacities. The validity of the proposed models is checked by comparing the results with experimental data. Good agreements between the test and proposed models' results are found with acceptable agreements. Moreover, design parameters, including the lightweight aggregate concrete (LWAC) strength, eccentricity, column slenderness ratio, and confinement, are studied using the FE analysis, and their efficiency factors are discussed. The results show that the ultimate axial capacity of the LACES composite columns subjected to eccentric loading is negatively affected by the increase in the columns' height, but it is positively affected by the increase of the confinement. Increasing the eccentricity and columns' height reduced the columns'stiffness. In addition, the ultimate capacity of the LACES column is significantly influenced by the LWAC strength and eccentricity, where the ultimate capacity of the LACES column is significantly increased by increasing LWAC strength, and it is remarkably decreased by increasing the eccentricity. When the eccentricity changed from zero to 70 mm, the ultimate axial capacity and stiffness decreased by 67.97% and 63.56%, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.11a
• /
• pp.357-360
• /
• 2004

Estimation of deformation capacity of non-flexural reinforced concrete members is proposed using basic concepts of limit analysis and the virtual work method. This new approach starts with construction of admissible stress field as for an equilibrium set. Failure mechanisms compatible with admissible stress fields are postulated as for displacement set. It is assumed that the ultimate deformations as result of failure mechanisms are controlled by ultimate strain of concrete in compression. The derived formula for deformability of deep beams in shear shows reasonable range of ultimate displacement.

• Journal of Korean Society of Steel Construction
• /
• v.30 no.2
• /
• pp.87-96
• /
• 2018

This study is aiming at investigating the ultimate behaviors and curling influence on the ultimate strength in high strength aluminum alloys (7075-T6) single shear two-bolted connections using finite element analysis. The validation of finite element analysis for predicting the ultimate behaviors was verified through the comparison between previous test results and analysis predictions. Strength reduction due to curling occurrence was estimated quantitatively. Parametric analyses with extended variables were conducted and the conditions of curling occurrence according to end distance and edge distance were suggested. Finally, modified equation was suggested considering curling influence on the ultimate strength of aluminum alloys 7075-T6 bolted connections.

• Journal of the Society of Naval Architects of Korea
• /
• v.46 no.1
• /
• pp.31-42
• /
• 2009

Common structural rule (CSR) doesn' t provide any other specific regulations for permanent means of access (PMA) platform structure in a cargo oil tank. The PMA platform is recommended to comply with scantling requirement of local support member. However, it leads to too conservative scantlings compared with actual loads imposed on the platform. This paper proposes a strength assessment procedure for the PMA structure based on a nonlinear ultimate strength. The ultimate strength is evaluated in a sufficiently conservative way. The first linear buckling mode is used as an initial imperfection shape and its magnitude is determined using the definitions of DNV PULS. Since the same imperfection mode as the failure mode of the ultimate limit state is assumed, it can accelerate the failure. Au ultimate strength capacity curve obtained from a series of nonlinear FE analysis is compared with actual stresses calculated by CSR cargo hold analysis.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4205-4209
• /
• 2011

Numerical analysis were executed in order to investigate ultimate lateral resistance of roots of vegetation. Ultimate lateral resistances of roots obtained from the assumed values of cohesions were distributed between the values of the two kinds of the existing studies. The ultimate lateral resistance values were more close to those by the bearing capacity solution than those by the cavity expansion theory. Coefficient of bearing capacity determined by the numerical analysis was 33. Yielding displacements obtained from the numerical analysis were 0.08~0.29 times of the diameter of the root and those were overall close to the value of the existing study which was undertaken for the pile diameter of 1 cm.

• Structural Engineering and Mechanics
• /
• v.11 no.5
• /
• pp.519-534
• /
• 2001

The effect of the initial imperfections on the nonlinear behaviors and ultimate strength of the thin-walled members subjected to the axial loads, obtained by the finite element stability analysis, are examined. As the initial imperfections, the bucking mode shapes of the members are adopted. The buckling mode shapes of the thin-walled members are obtained by the transfer matrix method. In the finite element stability analysis, isoparametric degenerated shell element is used, and the geometrical and material nonlinearity are considered based on the Green Lagrange strain definition and the Prandtl-Reuss stress-strain relation following the von Mises yield criterion. The U-, box- and I-section members subjected to the axial loads are adopted for numerical examples, and the effects of the initial imperfections on the nonlinear behaviors and ultimate strength of the members are examined.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.83-91
• /
• 1994

An efficient method was developed to determine the ultimate strength for the segment subjected to cross-sectional distortion. Cumulative data based on the finite element analysis were used to perform the multi-regression analysis. A moment-thrust-curvature relationship of short segment was obtained with mathematical forms in the nonlinear range. The extensive parametric study was performed to generate the ultimate strength for the various segments. The result was compared with the experimental result which was not included in the database. The proposed method gives an essential tool for the nonlinear analysis of beam-column.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2005.04a
• /
• pp.257-264
• /
• 2005

This paper presents the estimation of buckling coefficients and an ultimate strength for a longitudinally profiled plate (LP plate). From the buckling analysis of the LP plate compressed in one direction, the buckling coefficients for the thickness ratio are obtained by Rayleigh-Ritz method and Galarkin method. This paper also provides the technique of a finite element analysis considering the residual distributions of residual stresses and forces equilibrium in the LP plate. The strength behavior of the LP plate obtained from the analysis shows that the ultimate strength differs from the strength which is calculated from the current design code. Based on the results, this paper presents some new proposals about the strength evaluations of the LP plate.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.544-547
• /
• 2004

Predicting the failure modes of reinforced concrete corbels is difficult because the reinforced concrete corbels show the shapes of sudden shear failures at even slight deflection. For this reason, an exact analysis method is demanded highly. In this study, the validity of the grid softened strut-tie model method suggested for concrete member analysis was examined through the ultimate strength evaluation of the reinforced concrete corbels tested to failure. The evaluated ultimate strengths by the grid softened strut-tie model method were compared with those by the ACI 318-02 and the softened strut-tie model method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.501-506
• /
• 2000

An iterative numerical computational algorithm is presented to design a plate or shell element subjected to membrane and flexural forces. Based on equilibrium consideration, equations for capacities of top and bottom reinforcements in two orthogonal directions have been derived. The amount of reinforcement is determined locally, i.e., for each sampling point, from the equilibrium between applied and internal forces. Based on nonlinear analyses performed in a hyperbolic cooling tower, the analytically calculated ultimate load exceeded the design ultimate load from 50% to 55% for an analysis with relatively low to high tension stiffening, cases $\gamma$=10 and 15. For these cases, the design method gives a lower bound on the ultimate load with respect to Lower bound theorem, This shows the adequacy of th current practice at least for this cooling tower shell case studied. To generalize the conclusion more designs - analyses should be reformed with different shell configurations.