• 한국분말재료학회지
• /
• 제16권3호
• /
• pp.196-202
• /
• 2009

A visible-light photoactive $TiO_{2-x}N_x$ photocatalyst was synthesized successfully by means of cogrinding of anatase-$TiO_2(a-TiO_2)$ in $NH_3$ ambient, followed by heat-treatment at $200^{\circ}C$ in air environment. In general, it is well known that the grinding-operation induces phase transformation of a-$TiO_2$ to rutile $TiO_2$. This study investigates the influence of the amount of $NH_3$ gas on the phase transformation rate of a-$TiO_2$ and enhancement of visible-light photocatalytic activity, and also examines the relation between the photocatalytic activity and the period of grinding time. The phase transformation rate of a-$TiO_2$ to rutile is retarded with the amount of NH3 injected. And the visible-light photocatalytic activity of samples, was more closely related to the period of grinding time than $NH_3$ amount injected, which means that the doping amount of nitrogen into $TiO_2$ more effective to mechanical energy than $NH_3$ amount injected. XRD, XPS, FT-IR, UV-vis, Specific surface area (SSA), NOx decomposition techniques are employed to verify above results more clearly.

• 한국재료학회지
• /
• 제18권7호
• /
• pp.389-393
• /
• 2008

Nano-sized $TiO_2$-60 wt% SrO composite powders were synthesized by a sol-gel method using titanium isopropoxide and $Sr(OH)_2\;{\cdot}\;8H_2O$ as precursors. 3, -5, -7 wt%Ag spot-coated $TiO_2$-60 wt% SrO composite powders were synthesized by a Ag electroless deposition method using $TiO_2$-60 wt% SrO composite powders calcined at $1050^{\circ}C$, which mainly exhibited the $SrTiO_3$phase. However, a small number of rutile $TiO_2$, $Sr_2TiO_4$ and $SrO_2$ phases were also detected. In the Ag spot-coated powders synthesized by electroless deposition, nano-sized particles about 5-25 nm in diameter adhered to the $TiO_2$-60 wt% SrO composite powders. The photocatalytic activity of Ag spot-coated $TiO_2$-SrO and $TiO_2$-SrO composite powders for degradation of phenol showed that all of $TiO_2$-SrO composite powders were highly active under UV light irradiation. 7 wt%Ag spot-coated $TiO_2$-60wt.%SrO composite powders had a relatively higher photocatalytic activity than did $TiO_2$-SrO composite powders under visible light.

• 한국도로학회논문집
• /
• 제19권1호
• /
• pp.53-62
• /
• 2017

PURPOSES : This research was a fundamental study on the application of an integral $TiO_2$ solution to asphalt concrete pavement. The integral $TiO_2$ solution was produced in pilot production equipment; application of the integral $TiO_2$ solution to asphalt pavement was conducted to examine the pollution-reducing capability of photocatalytic compounds such as $TiO_2$. The photocatalytic $TiO_2$ reacted with air pollutants, converting them into small amounts of relatively benign molecules. METHODS : In this study, laboratory experiments were conducted using five various testing methods. Tensile strength ratio (TSR) and British pendulum test (BPT) were conducted in order to evaluate the properties of asphalt pavement subsequent to the integral $TiO_2$ solution coating. In addition, methylene blue testing, a measurement of nitrate on the coated pavement, and nitrogen oxide (NOx) reduction testing were conducted in order to evaluate photocatalytic reaction. Lastly, a UV-A lamp was used as a light source for photocatalytic reactions. RESULTS : Test results indicated no change in the properties of asphalt pavement following the integral $TiO_2$ solution coating. In order to evaluate the performance of asphalt pavement as a function of $TiO_2$, the moisture susceptibility and skid resistance were investigated. The moisture susceptibility and skid resistance satisfied there quirements related to pavement quality and safety specification. Furthermore, the effects of reduction of air pollution were significantly improved as determined via the methylene blue test and NOx reduction test. The $TiO_2$-paved asphalt specimen exhibited approximately 43% reduction of NOx. CONCLUSIONS : This study has suggested that applying $TiO_2$ rarely impacts asphalt pavement performance measures such as moisture susceptibility and skid resistance, and that its application may be a better means of reducing air pollution. Further studies, such as proper $TiO_2$ dosage rates and compatibility with various pavement types, are required to broaden and generalize its application.

• 한국재료학회지
• /
• 제13권10호
• /
• pp.691-696
• /
• 2003

To improve the photocatalyticactivity of $TiO_2$-coated coal fly ash, tungsten hydroxide was doped by impregnation method and was oxidized by heat treatment in temperature ranges of $WO^{\circ}C$ for 2 hrs. The changes of crystal structure and crystal size of $TiO_2$and $WO_3$on coal fly ash were investigated by X-ray diffraction analysis. The crystal structure of titanium dioxide showed only anatase type and $TiO_2$-$WO_3$ compounds appeared in the heat treatment temperature ranges of $500∼600^{\circ}C$. By adding $V_3$in $TiO_2$coated on fly ash, the growth of crystal size of anatase was restrained and the anatase phase was stabilized in temperature ranges of TEX>$500∼<800^{\circ}C$. And $WO_3$acted as a trap site of electrons excited from anatase by irradiating UV. The maximum removal efficiency of NO gas for $TiO_2$/$WO_3$-coated coal fly ash was 84% and appeared when the ammonium tungstate of $1.3${\times}$10^{-3}$ M was doped and then heated at $600^{\circ}C$ for 2 hrs.

• 상하수도학회지
• /
• 제29권1호
• /
• pp.33-38
• /
• 2015

In this study, flat-type photocatalytic reaction system is applied to reduce toxic hexavalent chromium (Cr(VI)) to trivalent chromium (Cr(III)) in aqueous solution under UV irradiation. To overcome the limitation of conventional photocatalysis, a novel approach toward photocatalytic system for reduction of hexavalent chromium including nanotubular $TiO_2$ (NTT) on two kinds of titanium substrates (foil and mesh) were established. In addition, modified Ti substrates were prepared by bending treatment to increase reaction efficiency of Cr(VI) in the flat-type photocatalytic reactor. For the fabrication of NTT on Ti substrates, Ti foil and mesh was anodized with mixed electrolytes ($NH_4F-H_2O-C_2H_6O_2$) and then annealed in ambient oxygen. The prepared NTT arrays were uniformly grown on two Ti substrates and surface property measurements were performed through SEM and XRD. Hydraulic retention time(HRT) and substrate type were significantly affected the Cr(VI) reduction. Hence, the photocatalytic Cr(VI) reduction was observed to be highest up to 95% at bended(modified) Ti mesh and lowest HRT. Especially, Ti mesh was more effective as NTT substrate in this research.

• 한국재료학회지
• /
• 제14권6호
• /
• pp.407-412
• /
• 2004

Photo decomposition of gas phase benzene by $TiO_2$ thin films chemically deposited on alumina balls were investigated under UV irradiation. Photo decomposition rates were measured in real time during the reaction using a photo ionization detector, which ionizes C-H bonding of benzene molecules and then converts into volatile organic compounds (VOCs) concentrations. From the measuring results, the VOCs concentration increased instantly when IN irradiated because C-H bonds of benzene molecules strongly absorbed on the surface of $TiO_2$ films before the IN irradiation was destroyed by photo decomposition. After that, the VOCs concentration decreased with increasing surface area of $TiO_2$ and reaction time under the IN irradiation. At the optimal conditions for the photo decomposition of gas phase benzene, the reaction rate of the photo decomposition for high concentrations (over 60 ppm) was slow but that of relatively low concentration (under 60 ppm) was fast, due to limited surface area of $TiO_2$ thin films for the reaction. Thus, it is concluded that the photo decomposition rate was mainly affected by the surface area of $TiO_2$ or absorption reaction.

• 한국분말재료학회지
• /
• 제27권5호
• /
• pp.381-387
• /
• 2020

In this work, TiO₂ 3D nanostructures (TF30) were prepared via a facile wet chemical process using ammonium hexafluorotitanate. The synthesized 3D TiO₂ nanostructures exhibited well-defined crystalline and hierarchical structures assembled from TiO₂ nanorods with different thicknesses and diameters, which comprised numerous small beads. Moreover, the maximum specific surface area of TiO₂ 3D nanostructures was observed to be 191 ㎡g^-1, with concentration of F ions on the surface being 2 at%. The TiO₂ 3D nanostructures were tested as photocatalysts under UV irradiation using Rhodamine B solution in order to determine their photocatalytic performance. The TiO₂ 3D nanostructures showed a higher photocatalytic activity than that of the other TiO₂ samples, which was likely associated with the combined effects of a high crystallinity, unique features of the hierarchical structure, a high specific surface area, and the advantage of adsorbing F ions.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2014년도 추계학술대회 논문집
• /
• pp.264-265
• /
• 2014

This Paper reports the photocatalytic activity of $g-C_3N_4/NaTaO_3$ hybrid composite photocatalysts synthesized by ball-mill method. The $g-C_3N_4$ and $NaTaO_3$ were individually prepared by Solid state reaction and microwave hydrothermal process, respectively. The $g-C_3N_4/NaTaO_3$ composite showed the enhanced photocatalytic activity for degradation of rhodamine B dye (Rh. B) under simulated solar light irradiation. The results revealed that the band-gap energy absorption edge of hybrid composite samples was shifted to a longer wavelength as compared to $NaTaO_3$ and the 50 wt% $g-C_3N_4/NaTaO_3$ hybrid composite exhibited the highest percentage (99.6 %) of degradation of Rh. B and the highest reaction rate constant ($0.013min^{-1}$) in 4 h which could be attributed to the enhanced absorption of the hybrid composite photocatalyst in the UV-Vis region. Hence, these results suggest that the $g-C_3N_4/NaTaO_3$ hybrid composite exhibits enhanced photocatalytic activity for the degradation of rhodamine B under simulated solar light irradiation in comparison to the commercial $NaTaO_3$.

• 한국재료학회지
• /
• 제15권8호
• /
• pp.508-513
• /
• 2005

[ $TiO_2-Fe_2O_3$ ] nanocomposite powders for magnetic photocatalyst were synthesized by sol-gel process, in which $TiO_2$ photocatalytic layer was formed on the surface of $\gamma-Fe_2O_3$ magnetic core. Transmission electron microscopy (TEM) observation and X-ray diffractometry (XRD) analysis revealed that$\gamma-Fe_2O_3$ nanoparticles, $10\~20nm$ in diameter, were coated by $TiO_2$ shell of 5nm in thickness and $TiO_2$ was anatase phase. Also hydroxyl group (-OH) used to decompose organic compounds was detected by Fourier transformation infrared spectrometry(FT-IR) analysis. UV-Visible spectrophotometry results showed that light absorption occurred in the wavelength range of $400\~700 nm$, and the band gap energy $(E_g)$ of powder was 1.8 eV. Finally it was found that the coercivity $(H({ci})$ and saturation magnetization $(M_s)$ of the powder were 79 Oe and 14.8 emu/g, respectively as experimental vibrating sample magnetometer (VSM) measurements.

• 한국환경과학회지
• /
• 제16권7호
• /
• pp.785-791
• /
• 2007

The current study evaluated the technical feasibility of the application of titanium dioxide ($TiO_{2}$) photo-catalytic air cleaners for the disinfection of bioaerosols present in indoor air. The evaluation included both laboratory and field tests and the tests of hydraulic diameter (HD) and lamp type (LT). Disinfection efficiency of photocatalytic oxidation (PCO) technique was estimated by survival ratio of bacteria or fungi calculated from the number of viable cells which form colonies on the nutrient agar plates. It was suggested that the reactor coating with $TiO_{2}$ did not enhance the adsorption of bioaerosols, and that the UV irradiation has certain extent of disinfection efficiency. The disinfection efficiency increased as HD decreased, most likely due to the decrease in the light intensity since the distance of the catalyst from the light source increased when increasing the HD. It was further suggested that the mass transfer effects were not as important as the light intensity effects on the PCO disinfection efficiency of bioaerosols. Germicidal lamp was superior to the black lamp for the disinfection of airborne bacteria and fungi, which is supported by the finding that the disinfection efficiencies were higher when the germicidal lamp was used compared to the black lamp in the laboratory test. These findings, combined with operational attributes such as a low pressure drop across the reactor and ambient temperature operation, can make the PCO reactor a possible tool in the effort to improve indoor bioaerosol levels.