• 한국철도학회논문집
• /
• 제17권1호
• /
• pp.43-51
• /
• 2014

철도에서 토공구조물은 입경이 큰 조립지반재료를 주요한 재료로 사용하고 있다. 그러나 이들 재료에 대한 미소변형 거동을 평가할 수 있는 동적물성 산정에 대한 연구는 대형시험장비의 부족으로 거의 이루어지지 않고 있다. 이에 본 연구에서는 국내 철도설계기준에 제시되어 있는 입도분포, 단위중량 등의 기본 조건에 맞는 강화노반(보조도상, 입도조정층), 접속부 자갈재료, 상부노반재료에 대해 대형반복삼축압축시험을 수행하여 저변형률 수준에 따른 정규화전단탄성계수와 감쇠비곡선을 제안하고, 각 재료별로 수식 모델과 계수를 제시하였다.

• 한국지반공학회논문집
• /
• 제38권8호
• /
• pp.7-15
• /
• 2022

대부분의 선행연구는 동결 삼축압축시험 수행 시, 몰드를 사용하여 시료를 조성하고 단방향으로 동결을 진행하였다. 이는 동결된 시료에 잔류응력이 발생할 가능성이 있기 때문에 인공동결공법이 적용된 지반을 모사하는데 한계가 있다. 본 연구에서는 기존 시험방법의 한계를 보완할 수 있는 시험장비 및 시험방법을 제안하고, 제안된 방법으로 온도 및 구속압력에 따른 동결 사질토의 역학적 특성을 평가하였다. 동결온도가 낮아질수록 동결 사질토는 취성이 증가하였고, 부동수분의 감소 및 얼음자체의 강도 증가로 인하여 강도가 증가하였다. 구속압력의 증가는 강도저감 효과를 발생시키는 압력융해 현상과 강도증진 효과를 발생시키는 흙 입자의 마찰력 증가 모두를 야기하였다. 이처럼 동결 사질토의 역학적 거동은 구속압력과 동결온도의 복합적인 영향을 받는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 봄 학술발표회 논문집
• /
• pp.639-646
• /
• 2000

It is important to estimate the mechanical properties of clay since it is directly related to the design and the construction of geotechnical structures. Site exploration, which is composed of boring, sampling, in-situ, or laboratory tests, is preformed to estimate the mechanical properties. However, mechanical properties of clay measured from laboratory test may be different from in-situ properties due to disturbances occurred during sampling, transportation, storage, and trimming. In this study, the degree of disturbance according to sampling method was estimated with the test results of CK/sub o/U triaxial compression test on Yangsan clay. The soil samples were obtained by three types of sampling method, j.e., 76mm-tube sampler, 76mm-piston sampler, and block sampler. In order to evaluate the quality of samples, volumetric strain, undrained shear strength, secant Young's modulus, and pore pressure coefficient at peak measured from each sample were compared with one another. From the test results, it was observed that mechanical properties of the block and piston samples were more reliable than those of tube samples. But it was observed that the water content of piston was similar to that of tube samples at given depths while the water content of block samples was 14.3∼15.8% smaller than that of piston and tube samples. In addition to the evaluation of the quality of samples, relationship between c/sub u// σ/sub vc/'and OCR was established from the results of the CK/sub o/U triaxial compression tests, which were carried out using SHANSEP method. And also undrained shear strength was analyzed using the in-situ test data such as Cone Penetration Test(CPT), Dilatometer Test(DMT), and Field Vane Test(FVT) and was compared with that evaluated from CK/sub o/U triaxial compression test.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.1142-1150
• /
• 2010

An elementary particle of bottom ash is similar to fine sand. So which expected from replace expensive sand. Therefore, this study conducts cyclic triaxial test and a resonant test using relative density, which is obtained from a relative density test of bottom ash and standard sand. Also, it compares antiseismic characteristics of bottom ash and standard sand in order to analyze the possibility of commercial use as a construction material.

• 한국지반환경공학회 논문집
• /
• 제10권1호
• /
• pp.25-34
• /
• 2009

댐이나 항만 건설시 재료로 사용되는 조립재는 입자크기가 일반 토사에 비해 매우 크기 때문에 이러한 재료에 대해서 전단시험을 수행할 때에는 가급적 대형 전단시험장치를 사용하는 것이 보다 정확한 결과를 얻기 위해 바람직하다. 대형 전단시험장치로는 일반적으로 대형 직접전단시험장치와 대형 삼축압축시험장치가 있으나 일반 토질시험장치와 비교해 제작과 보급, 운영 등의 어려움 때문에 현재까지 국내에서 두 시험장치를 사용하여 시험을 수행한 실적은 많지 않은 편이다. 본 연구에서는 댐 축조재로 사용되는 입경이 큰 조립재료를 대상으로 시료의 평균 입자크기와 공시체 크기, 연직응력(구속압) 조건 등에 차이가 있는 총 6개 case에 대해서 대형 직접전단시험과 대형 삼축압축시험을 수행하고 두 시험간 전단강도 특성의 차이를 비교하였다. Mohr-Coulomb 강도규준에 의한 전단강도를 기준으로, 대형 직접전단시험을 통해 산정된 전단강도가 대형 삼축압축시험을 통해 산정된 전단강도보다 전체적으로 크게 나타났으며 또한, 1,000kPa 수직응력에 대해 두 시험간 산정된 전단강도를 비교한 결과 대형 직접전단시험에 의한 전단강도가 대형 삼축압축시험에 의한 전단강도보다 약 10~70% 크게 나타나 입경이 작은 일반 토사와 비교해 그 차이가 크고, 대형 직접전단시험결과의 분산도가 상대적으로 높은 것으로 나타났다.

• 한국정밀공학회지
• /
• 제28권2호
• /
• pp.226-232
• /
• 2011

In this study, an optimized design of a triaxial load cell has been developed by the use of finite element analysis, design of experiment and response surface method. The developed optimal design was further validated by both stress-strain analysis and natural vibration analysis under an applied load of 30 kgf. When vertical, horizontal, and axial loads of 30 kgf were applied to the load cell with the optimal design, the calculated strains were satisfied with the required strain range of $500{\times}10^{-6}{\pm}10%$. The natural vibration analysis exhibited that the fundamental natural frequency of the optimally designed load cell was 5.56 kHz and higher enough than a maximum frequency of 0.17 kHz which can be applied to the load cell for wind-tunnel tests. The satisfactory sensitivity in all triaxial directions also suggests that the currently proposed design of the triaxial load cell enables accurate measurements of the multi-axial forces in wind-tunnel tests.

• 한국산학기술학회논문지
• /
• 제11권10호
• /
• pp.4012-4017
• /
• 2010

이 연구에서는 팩 말뚝과 모래다짐말뚝의 전단강도 특성을 비교하기 위해 모래-팩-점토 복합토 및 모래-점토 복합토를 인위적으로 치환율($a_s$) 10%, 20%로 재성형하여 구속압력을 변화시켜가며 삼축압축시험(CU Test)을 실시하였다. 시험결과 모래-점토 복합토에 비해 모래-팩-점토 복합토의 강도가 치환율 10% 및 20% 모두에서 훨씬 크게 측정되어 모래다짐말뚝보다 팩말뚝이 큰 지지력을 갖는다는 것을 확인하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1039-1046
• /
• 2005

After clay particles have been sediment isotropically, the clay deposits have been consolidated under $K_0$-stress system. Therefore, in order to predict the behavior in-situ of normally consolidated clays, the laboratory test should be enforced under $K_0$-stress system and should obtain the characteristics of normally consolidated clays. And relationship of stress-strain on clay is effected on not only method of consolidation but also characteristic of visco-plastic behavior. Saturated clay is effected more this trend. So, rate of strain is considered to understand exact stress-strain relationship. In this study, the series of undrained triaxial compression tests were preformed on remolded specimens which was made by slurry of clay, consolidated under $K_0$-stress systems. And the undrained triaxial compression test were preformed to examine behavior of stress-strain relationship due to rate of shear strain relationship due to rate of shear strain.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.1017-1024
• /
• 2009

In the past few decades, the rockfill embankment dam, which has superior workability and economy, has become a major trend. In Korea, most of the embankment dams are rockfill dams, but recently, in response to the demand for sustainable development and environmentally-friendly water resource development, the sand and gravel in streams has become a major construction material for dams, rather than the non-economic rockfill, and its application examples have also increased. In this study, a large triaxial test was performed, with construction samples of different maximum sizes, in parallel with the grading method at the 'B Dam' construction site in Korea, and the effects of the different maximum sizes on the strain of the dam construction material and on the shear strength characteristics were analyzed to provide the basic data for determining the strength characteristics of the coarse-grained materials by the maximum size.

• Geomechanics and Engineering
• /
• 제21권4호
• /
• pp.327-336
• /
• 2020

Conventional researches on the behavior of fiber-reinforced and unreinforced soils often investigated the failure point. In this study, a concept is proposed in the comparison of the fiber-reinforced with unreinforced sand, by estimating the strength and strength ratio at different levels of strain. A comprehensive program of laboratory drained triaxial compression test was performed on compacted sand specimens, with and without date palm fiber. The fiber inclusion used in triaxial test specimens was form 0.25%-1.0% of the sand dry weight. The effect of the fiber inclusion and confining pressure at 0.5%, 1.0%, 1.5%, 3.0%, 6.0%, 9.0%, 12%, and 15% of the imposed strain levels on the specimen were considered and described. The results showed that, the trend and magnitude of the strength ratio is different for various strain levels. It also implies that, using failure strength from peak point or the strength corresponding to the axial strain of approximately 15% for evaluating the enhancement of strength or strength ratio, due to the reinforcement, may cause hazard and uncertainty in practical design. Therefore, it is necessary to consider the strength of fiber-reinforced specimen at the imposed strain level, compared to the unreinforced specimen.