• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.3
• /
• pp.224-234
• /
• 2007

Large diameter tubes have been used until comparatively lately. However, small diameter tubes are largely used because of their high efficiency in heat transfer and low cost, recently. This study focuses on the experimental research of the heat transfer coefficients during evaporation process of R-22 and R-134a in small diameter tubes. The evaporation heat transfer coefficients were measured in smooth horizontal copper tubes with ID 1.77, 3.36 and 5.35 mm. The evaporation heat transfer coefficients in the small diameter tubes (ID <7 mm) were observed to be strongly affected by the size of tube diameters and to differ from those of general predictions in the large diameter tubes. The heat transfer coefficients of ID 1.77 mm copper tube were higher by 20 and 30 % than those of ID 3.36 mm, ID 5.35 mm copper tubes respectively. Also, it was found that it was very difficult to apply some well-known previous predictions (Shah's, Jung's. Kandlikar's and Oh-Katsuda's correlation) to small diameter tubes. Based on the data, the new correlation is proposed to predict the evaporation heat transfer coefficients of R-22 and R-134a in small diameter tubes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.04b
• /
• pp.100-103
• /
• 2000

In the case of immobilizing of glucose oxidase into polypyrrole (PPy) using electrosynthesis, the glucose oxidase (GOx) forms a coordinate bond with the polymers backbone. However, because of intrinsic insulation and net-chain of the enzyme, the charge transfer and mass transport are obstructed during the film growth. Therefore, the film growth is dull. We synthesized the enzyme electrode by electropolymerization added some organic solvent. A formative seeds of film growth is delayed by adding ethanol. The delay is induced by radical transfer between ethanol and pyrrole monomer. The radical transfer shares the contribution of dopant between electrolyte anion and GOx polyanion. This may lead to increase amount of immobilized the enzyme in PPy. For the UV absorption spectra of synthetic solution before synthesis and after, in the case of ethanol added, the optical density was slightly decreased for the GOx peaks. It suggests amount of GOx in the solution was decreased and amount of GOx in the film was increased. We established qualitatively that amount of immobilization can be improved by adding a little ethanol in the synthetic solution. It is due to radical transfer reaction. The radical transfer shares the contribution of dopant between small and fast electrolyte anion and big and slow GOx polyanion.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.4 no.1
• /
• pp.48-56
• /
• 1992

The purpose of this study was to investigate the enhancement of heat transfer without additional external power in the case of rectangular air jet impinging vertically on the flat heating surface. In an attempt to enhance the heat transfer rate in two-dimensional impinging jet, the technique used in the present study was placement of square rod bundles as a turbluence promoter in front of the heat transfer surface. The effects of the clearance between the flat plate and square rod, and the nozzle exit velocity on the heat transfer characteristics have been investigated experimentally. The results obtained through this study were summerized as follows. High heat transfer enhancement was achived by means of flow acceleration and thinning of boundary layer by inserting rods in front of the heating flat plate. The smaller the clearance between rod and heating plate was, the larger heat transfer effect became. Average Nusselt number reached maximum at $Re=5.76{\times}10^4$ and C＝1㎜ and the enhancement rate of heat transfer became maxium at this condition with the enhancement ratio as high as about 1.427 when normalized by the flat plate value. The correlating equation of average Nusselt number and Reynolds number was obtained, which is $\bar{N}uo=1.324{\cdot}Re^{0.459}{\cdot}(C/A)^{-0.034}$.

• Journal of Korean Society of Transportation
• /
• v.26 no.4
• /
• pp.217-227
• /
• 2008

The purpose of this research is the estimation of a transfer ratio according to transfer time reflecting passenger attributes such as sex, age, income, job, the car ownership, and other variables with the assumption that a transfer ratio would be different depending on each passenger attribute. This research tested transfer time through a question-survey, estimated transfer time according to the passenger attributes using a data sample, and presented some applicable models about marginal transfer time for the case of the determination of transfer ratios according to transfer time. In this research the sample which had been surveyed for passengers walking to access a transfer station was used to test and estimate and the question was present walking time to the transfer time and the marginal transfer walking time.

• Journal of the Korean Mathematical Society
• /
• v.34 no.2
• /
• pp.383-393
• /
• 1997

In this paper, we study the dependence of corestriction (or transfer) map on the choice of transversals. We also study transfer theorems with respect to some commutative subgroups.

• Knowledge Management Research
• /
• v.18 no.4
• /
• pp.261-286
• /
• 2017

Key factors enhancing transfer behavior of training and knowledge sharing are of great interest to researchers and executives because training transfer and knowledge sharing activities are remarkable predictors of organizational growth. This study investigates the core motivations for boosting transfer behavior of training and knowledge sharing. To empirically test the impacts of employee training, servant leadership and self-efficacy, a survey was conducted in small-medium sized companies. The data (N=292) were analyzed using structural equation modeling analysis. The results indicate that higher employee training positively leads to self-efficacy and transfer behavior of training. Servant leadership is positively leads to self-efficacy, transfer behavior of training, and knowledge sharing. Self-efficacy of employees induces greater transfer behavior of training and knowledge sharing. Finally, transfer behavior of training encourages workers to increase knowledge sharing. This study represents an initial step to examine the psychological mechanism of improving employees' transfer behavior of training and knowledge sharing activities based on the employee training qualities and servant leaderships.

• Journal of Mechanical Science and Technology
• /
• v.16 no.1
• /
• pp.109-115
• /
• 2002

Vortex generators are fabricated on the fin surface of a fin-tube heat exchanger to augment the convective heat transfer. In addition to horseshoe vortices formed naturally around the tube of the fin-tube heat exchanger, longitudinal vortices are artificially created on the fin surface by vortex generators. The purpose of this study is to investigate the local heat transfer phenomena in the fin-tube heat exchangers with and without vortex generators, and to evaluate the effect of vortices on the heat transfer enhancement. Naphthalene sublimation technique is employed to measure local mass transfer coefficients, then analogy equation between heat and mass transfer is used to calculate heat transfer coefficients. Experiments are performed for the model of fin -circular tube heat exchangers with and without vortex generators, and of fin-flat tube heat exchangers with and without vortex generators. Average heat transfer coefficients of finn-flat tube heat exchanger without vertex generator are much lower than those of fin-circular tube heat exchanger. On the other hand, fin-flat tube heat exchanger with vortex generators has much higher heat transfer value than conventional fin-circular tube heat exchanger At the same time, pressure losses for four types of heat exchanger is measured and compared.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.280-287
• /
• 2001

The present study investigates convective heat/mass transfer and flow characteristics inside the rib-roughened cooling passage of the gas turbine blades. A square duct with rectangular ribs is used and $\wedge-$ and V-shape ribs with $60^{\circ}$ attack angle are installed on the test plate surfaces. Naphthalene sublimation technique is employed to determine the detailed local heat transfer coefficients using the heat and mass transfer analogy. The ribs disturb the main flow resulting in the recirculation and secondary flows near the ribbed wall and the vortices near the side-wall. The local heat transfer and the secondary flow in the duct are changed largely according to the rib orientation. A square duct with $\wedge$ and V-shape ribs has two pairs of secondary flow because of the rib arrangement. So, the duct has complex heat/mass transfer distribution. The average heat/mass transfer coefficient and pressure drop of $\wedge-$ and V-shape ribs are higher than those with $90^{\circ}$ and $60^{\circ}$ attack angles. The average heat/mass transfer coefficient on the $\wedge-shape$ ribs is higher than that on the V-shape ribs. Also, the uniformity of heat/mass transfer coefficient on discrete ribs is higher than that on continuous rib.

• Journal of the Korean Applied Science and Technology
• /
• v.28 no.3
• /
• pp.367-373
• /
• 2011

This research is a basic researching process for producing solid fuel that mixing paper sludge and Heat Transfer Medium Oil. Under the presence of Heat Transfer Medium Oil, paper sludge is heated and dried with home appliance microwave for comparing drying efficiency and energy efficiency of different types of drying method. As a result, Heat Transfer Medium Oil and paper mixing case of drying method, OMD, is the most efficient way to shorten the time for evaporating moisture in the paper sludge. In addition, heat transfer effect and density is increased with adding Heat Transfer Medium Oil by microwave. Future more, OMD's energy cost for evaporating whole moisture is 78% cheaper than MD. Also, OMD process shows the best energy efficiency with comparing other process. Evaporation rate of paper sludge evaporation process with microwave is 11.66% increased by adding Heat Transfer Medium Oil 150g. Preheating Heat Transfer Medium Oil or improving different ways injecting Heat Transfer Medium Oil is a good way to increase a rate of initiative moisture evaporation process.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.1225-1228
• /
• 2005

This paper compares the differences between Java virtual machine and x86 processor in data transfer viewpoint. Memory models of JVM and x86 are analyzed and the data transfer paths are identified. As all operations must be performed to the values on operand stack, a great many data transfer operation is unavoidable in JVM. We also lists the number of data transfer operations necessary for executing some typical high-level language statements including assignment, arithmetic, conditional, and iterative statements.