• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.112-117
• /
• 1997

This paper presents a GA(Genetic Algorithms)-Optical control strategy for the control of the swing motion and the transverse position of the overhead crane. The overhead crane system is defined uncertain due to unknown system parameters such as payload and trolly mass. To control the overhead crane. the GA-Optimal control scheme is suggested. which transfers a trolly to a desired place as fast as possible and minimizes the swing of the payload during the transfer. The genetic algorithms are applied to fine digital optimal feedback gains. A computer simulation demonstrate the performance of the proposed the GA-digital optimal controller for the overhead crane.

• Journal of Ocean Engineering and Technology
• /
• v.25 no.4
• /
• pp.7-11
• /
• 2011

The installation phase for a topside module suggested can be divided into 9 stages, which include start, pre-lifting, lifting, lifted, rotating, positioning, lowering, mating, and end of installation. The transfer of the topside module from a transport barge to a crane vessel takes place in the first three stages, from start to lifting, while the transfer of the module onto a floating spar hull occurs in the last three stages, from lowering to the end. The coupled multi-body motions are calculated in both calm water and in irregular waves with significant wave height (1.52m), with suggested force equilibrium diagrams. The effects of the hydrodynamic interactions between the crane vessel and barge during the lifting stage have been considered. The internal forces caused by the load transfer and ballasting are derived for the lifting phases. The results of these internal forces for the calm water condition are compared with those in the irregular sea condition. Although the effect of pitch motion on the relative vertical motion between the deck of the floating structure and the topside module is significant in the lifting phases, the internal force induced pitch motion is too small to show its influence. However, the effect of the internal force on the wave-induced heave responses in the lifting phases is noticeable in the irregular sea condition because the transfer mass-induced draught changes in the floating structure are observed to have higher amplitudes than the external force induced responses.

• Journal of the Korea Society for Simulation
• /
• v.12 no.3
• /
• pp.21-29
• /
• 2003

The operation rules to remarshaling works in yard is very important in automated container terminal (ACT). However, the decision rules for conventional container terminals have some restrictions to be applied to ACT whose block layout Is vortical for berth. The objective of this study is to propose the efficient operations rules for remarshaling works of automated transfer crane (ATC) in ACTs. Then, the various operation rules are simulated to verify the proposed operation rules. The results of the simulation study on various rules are provided and discussed.

• Journal of Power System Engineering
• /
• v.12 no.6
• /
• pp.42-49
• /
• 2008

The most important job in the container terminal area is to handle the cargo effectively in the limited time. To achieve this object, many strategies have been introduced and applied to. If we consider the automated container terminal, it is necessary that the cargo handling equipments are equipped with more intelligent control systems. From the middle of the 1990's, an automated rail-mounted gantry crane(RMGC) and rubber-tired gantry crane(RTG) have been developed and widely used to handle containers in the yards. Recently, in these cranes, the many equipments like CCD cameras and sensors are mounted to cope with the automated terminal environment. In this paper, we try to support the development of more intelligent automated cranes which make the cargo handling be performed effectively in the yards. For this plant, the modelling, tracking control, anti-sway system design, skew motion suppressing and complicated motion control and suppressing problems must be considered. Especially, in this paper, the system modelling and tracking control approach are discussed. And, we design the tracking control system incorporating an observer based on the 2DOF servo system design approach to obtain the desired state informations. In the case of observer design, a weighted $H_{\infty}$ error bound approach for a state estimator is considered. Based on an algebraic Riccati equation(inequality) approach, a necessary and sufficient condition for the existence of a full-order estimator which satisfies the weighted $H_{\infty}$ error bound is introduced. Where, the condition for existence of the estimator is denoted by a Linear Matrix Inequality(LMI) which gives an optimized solution and observer gain. Based on this result, we apply it to the tracking control system design for the transfer crane.

• Journal of Navigation and Port Research
• /
• v.26 no.5
• /
• pp.537-542
• /
• 2002

Recently, an automatic crane control system is required with high speed and rapid transportation. Therefore, when container is transferred from th intial coordinate to the finial coordinate, the container paths should be built in terms of the least time and no swing. So in this paper, we calculated the anti-collision path for avoiding collision in its movement to the finial coordinate. And we constructed the neural network predictive PID (NNPPID) controller to control the precise navigation. The proposed predictive control system is composed of the neural network predictor, PID controller, neural network self-tuner which yields parameters of PID. Analyzed crane system through simulation, and proved excellency of control performance than other conventional controllers.

• Journal of Fisheries and Marine Sciences Education
• /
• v.25 no.4
• /
• pp.998-1007
• /
• 2013

At container terminals, a major measurement of productivity can be work efficiency. For improving the productivity of container crane, the more efficient container yard operation method is necessary in container terminals. Recently, container terminal operators make an experiment on the dual cycle operation, which ship loading/unloading were carried out simultaneously, for increasing the productivity of container crane. In this paper, propose a system operating efficient dual cycle methods as utilize Ad-hoc technology in distributed port operation system. The dual cycle methods that proposed recognizes position information of Y/T during an action in Ad-hoc networks in case of container transfer works by real time as load an Ad-hoc module to Y/T taking charge of a container transfer with quay and yard. Utilize Ad-hoc networks technology in an operating system of container yard, and efficiently distributed processing done Y/T to container crane compare with operation systems of the existing dedicated method, and an improvement can do an operating system of an yard.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1465-1467
• /
• 2005

In this paper, the harbor container crane which transports containers between a container ship and trucks in the harbor is modeled. The equation of motion is simplified for control purpose. The pole placement technique is used to control the crane to minimize load swing angle The objective of the control is to transfer the load as quickly as possible, while minimizing the amplitude of swing at the end of transfer. Computer simulations are provided.

• Journal of Navigation and Port Research
• /
• v.32 no.6
• /
• pp.465-471
• /
• 2008

As the excessive competition between container terminals has been deepening, not only productivity, but also cost economic of the terminals has been raised. With regard to this, the competitiveness of the terminals is limited because of inefficiency operation of transfer crane(T/C) which needs large amount of energy consumption. Therefore, it is possible that the improvement in the T/C operation leads to saving cost for resources and energy as well as increasing the productivity of the terminals. This study provides 'the K-Means Clustering based Optimized Decision Model for Transfer Crane Operation', referring to 'RFID & RTLS based Port Logistics Initiative' of Ministry of Land, Transportation and Maritime Affairs and estimates the efficiency through simulating.

• Proceedings of the KIEE Conference
• /
• 2002.07d
• /
• pp.2788-2790
• /
• 2002

In this paper, we designed neural network predictive two degree of freedom PID controller to control sway of crane Crane's trolley arrive minimum oscillation of transfer body and establishment position in minimum time. When various establishment location and surrounding disturbance were approved based on mathematical modeling of crane, controller designed to become effective control location error and oscillation angle of two control variables that simultaneously can predictive control. We wish to develop automatic travel control system through anti-sway skill of crane.

• Journal of Navigation and Port Research
• /
• v.29 no.6 s.102
• /
• pp.555-560
• /
• 2005

Recently, many control systems are replaced with digital control systems in an effort to optimize the overall performance. In order to operate these systems efficiently, the conventional point-to-point connection method must be changed to the signal exchange via a communication network. This paper investigates the technical feasibility of the crane system using CAN protocol which is a part NMEA 2000 by implementing a network-based control system emulating the crane control system.