• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 추계학술대회 논문집
• /
• pp.127-131
• /
• 2003

This paper describes an initial pole position estimation method of a magnetic pole sensorless permanent magnet synchronous motor(PMSM) with an incremental encoder, The accurate initial pole position is estimated by using an efficient numerical method of Secant Method, which finds either of two zero torque/force positions and then the correct d-axis. It can be simply applicable to both rotary and linear PMSM because it only requires the tuned current controller and the relative position information. The experimental results show the validity of the proposed method with respect to highly accurate pole position estimation under the moderate moving distance and convergence time.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.225-229
• /
• 1998

If there is a mismatch between the controller programmed rotor time constant and the actual time constant of motor, the decoupling between the flux and torque is lost in an indirect rotor field oriented control. This paper presents a new estimation scheme for rotor time constant using artificial neural networks. The parameters of induction motor model organize 2 layer neural to be weight between neuron, which is proposed new in this paper. This method makes networks simple, so its brings not only the improvement in speed but simplification in calculation. Furthermore, it is possible to estimated rotor time constant real time through on-line learning without using off-line learning. The digital simulation and the experimental results to verify the effectiveness of the new method are described in this paper.

• Journal of Power Electronics
• /
• 제18권3호
• /
• pp.817-825
• /
• 2018

In this paper, a current hysteresis control with good decoupling properties for doubly-fed brushless induction machines (BDFIMs) has been proposed based on a generalized vector model. The independent control of the reactive power and speed for BDFIMs has been achieved by controlling the d-axis and the q-axis current of the control windings (CW). The proposed vector control method has been developed for the power winding (PW) flux frame. Experimental verification of a type Y180M-4 BDFIM prototype with 1/4 pole-pairs has been presented. Evidence of its good performance has been shown through experimental results.

• 대한전기학회논문지
• /
• 제39권2호
• /
• pp.164-174
• /
• 1990

The improvement of linearized characteistics of induction motor control system with field oriented method is presented in this paper. A fully digitally controlled induction motor driver system based on the proposed linear control condition is described. The control system consists of IBM-PC/AT microcomputer, VSI PWM Inverter, and PI controller with softwave. By controlling the torque component, the rated flux component can be kept constant, even in the transient state. It is clearly confirmed by experiment that the improvement of the vector control condition is satisfactory. A simplified control model of an induction motor similar to the model for a separately excited DC motor drive system is obtained.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.325-328
• /
• 2002

In this paper, we proposed that the problem of controlling induction motor with magnetic saturation is studied from an input-output feedback linearization with adaptive algorithm. The $\pi$-model of induction motor is considered. An adaptive input-output feedback linearizing controller is considered under the assumption of known motor parameters and unknown load torque. Simulation results are provided for illustration.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.244-244
• /
• 2000

We proposed the above-knee prosthesis using rotary MR damper in which knee joint is semi-actively controlled by microprocessor. Dissipation torque in the knee joint can be controlled by the magnetic field which is induced by applying current to a solenoid, Tracking control of knee joint angle was tested by 3-DOF Leg simulator. The experimental results show that the proposed above-knee prosthesis system had good performance in swing phase tracking and repetitive controller in conjunction with a computed control law and PD control law, reduced RMS tracking error as the repetitions of tracking. Moreover, desired knee angle trajectory was generated based on the estimation of gait period with the gyro signal and the tracking control was performed.

• 한국정밀공학회지
• /
• 제8권3호
• /
• pp.64-72
• /
• 1991

This paper deals with the state estimator and controller. All state variables' feedback in the system were used to improve electro hydraulic servo sysem were used to improve electro hydraulic servo system's responese charact- eristics. Many gains of the state variables'and estimator's are produced by the algebraic Riccati equation, and every state variables'optimal gain and estimator gain is selected by trial and error method. For the designed estimator performance's examination, this paper simulate the time response for the step input, the reduced velocity output in subjected to load torque, and the time response for the step input in changing the inertiamoment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.105-108
• /
• 1988

In this paper, a control system design method is proposed for DC motor drive. A state space model is used to control sysytem and for closed loop system the technique of pole assignment is applied. The control system is designed with state feedback theory and to improve the response further more feedforward theory is applied to control system. The microprocessor as a controller and the interfaces in the system are proposed. Digital simulation results for step changes in reference velocity and load torque are shown.

• Journal of Electrical Engineering and information Science
• /
• 제2권3호
• /
• pp.113-122
• /
• 1997

An adaptive input-output linearization technique for a robust speed control of a brushless C(BLDC) motor is presented. By using this technique, the nonlinear moro model can be effectively linearized in Brunovski canonical form, an the desired speed dynamics can be obtained based on the linearized model. This control technique, however, gives an undesirable output performance under the mismatch of the system parameters and load conditions caused by the incomplete linearization. for the robust output response, the controller parameters will be estimated by a model reference adaptive technique where the disturbance torque and flux linkage are estimated. The adaptation laws are derived by the Popov's hyperstability theory nd positivity concept. The proposed control scheme is implemented on a BLDC motor using the software of DSP TMS320C30 and the effectiveness is verified through the comparative simualtions and experiments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.265-269
• /
• 1994

The switching dead time avoiding a bridge leg short circuit in PWM voltage source inverter produces distortions of the controlling inverter output performance such as current waveform, voltage vector, and torque. In this paper, the influence of dead time is investigated. The on-line space voltage vector modulation method is used for current controller. It is possible to compensate dead time by space voltage vector modulation which generates additional pulse compensating voltage distortion caused by dead time. In addition, narrow pulse which is generally neglected can be compensated. All the algorithms, including field-oriented control are performed by one chip microprocessor 80C196MC and DSP TMS320C31. Experimental results probe that the proposed scheme provides a good inverter output performance.