• 한국전기전자재료학회논문지
• /
• 제16권5호
• /
• pp.390-396
• /
• 2003

As the design rule of device continued to shrink, the contact resistance in small contact size became important. Although the conventional TiN/Ti structure as a ohmic layer has been widely used, we propose a new TiN/Co film structure. We characterized a contact resistance by using a chain pattern and a KELVIN pattern, and a leakage current determined by current-voltage measurements. Moreover, the microstructure of TiN/ Ti/ silicide/n$\^$+/ contact was investigated by a cross-sectional transmission electron microscope (TEM). The contact resistance by the Co ohmic layer showed the decrease of 26 % compared to that of a Ti ohmic layer in the chain resistance, and 50 ％ in KELYIN resistance, respectively. A Co ohmic layer shows enough ohmic behaviors comparable to the Ti ohmic layer, while higher leakage currents in wide area pattern than Ti ohmic layer. We confirmed that an uniform silicide thickness and a good interface roughness were able to be achieved in a CoSi$_2$ Process formed on a n$\^$+/ silicon junction from TEM images.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.279-284
• /
• 2003

The $CoSi_2$ process is widely employed in a salicide as well as an ohmic layer process. In this experiment, we investigated the characteristics of $CoSi_2$ films by combinations of I-type (TiN 100$\AA$/Co 150$\AA$), II-type(TiN 100$\AA$/Co 150$\AA$/Ti 50$\AA$), III-type(Ti 100$\AA$/Co 150$\AA$/Ti 50$\AA$), and IV-type(Ti 100$\AA$/Co 150$\AA$/Ti 100$\AA$). Sheet resistances of $CoSi_2$ show the lowest resistance with 2.9 $\Omega$/sq. in a TiN/Co condition and much higher resistances in conditions simultaneously applying Ti capping layers and Ti interlayers. Though we couldn't observe a $CoSi_2$roughness dependence on the film stacks from RMS values, Ti capping layers turned into 78∼94$\AA$ thick TiN layers of (200) preferred orientation at $N_2$ambient. In addition, Ti interlayers helped to form the epitaxial $CoSi_2$with (200) preferred orientation and ternary compounds of Co-Ti-Si. We propose that film structures of II-type and III-type may be appropriate in the salicide process and the ohmic layer process from the viewpoint of Co diffusion kinetics and the CoSi$_2$epitaxy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1378-1380
• /
• 2001

Ohmic contacts have been fabricated on p-type 4H-SiC using Pt/Ti. Low resistivitf Ohmic contacts of Pt/Ti to p-type 4H-SiC were investigated. Specific contact resistances were measured using the transmission line model method, and the physical properties of the contacts were examined using x-ray diffraction, scanning electron microscopy. Ohmic behavior with linear current-voltage characteristics was observed following anneals at $900^{\circ}C$ for 90sec at a pressure of $3.4{\times}10^{-5}$ Torr. The Pt/Si/Ti films was measured lower value of the specific contact resistance by the annealing process, and the contact resistances were improved more than one order compared to Ti contact the annealed sample. Scanning electron microscopy shows that the Pt layer effectively reduce the oxidation of Ti films. And results are obtained as $4.6{\times}10^{-4}$ ohm/$cm^2$ for a Pt/Ti metal structure after a vacuum annealing at $900^{\circ}C$ for 90sec. Titanium has a relatively high melting point, thus Ti-based metal contacts were attempted in this study.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.154-154
• /
• 2009

Cr capping layer를 이용하여 Titanium germanide의 열적 안정성을 향상시키는 연구를 수행하였다. n-type Ge(100) 기판 위에 전자빔 증착기를 이용하여 30nm 두께의 Ti와 Cr capping layer를 증착하고 $400\;^{\circ}C$에서 $800\;^{\circ}C$까지 30초간 N2 분위기로 급속 열처리하여 Ti germanide를 형성하였다. XRD결과로부터 Cr capping layer의 유무에 관계 없이 Ti germanide가 형성된 것을 관찰할 수 있었다. Ge 기판 위에 CTLM 패턴을 형성하고 실험을 진행하여 Ti germanide의 I-V 측정 데이터를 통해 Ohmic 특성을 알아보았고, contact resistance, sheet resistance, specific contact resistance를 구하였다.

• 한국전기전자재료학회논문지
• /
• 제20권3호
• /
• pp.234-239
• /
• 2007

This paper describes the TiW ohmic contact characteristics under the surface treatment of the polycrystalline 3C-SiC thin film grown on $SiO_2/Si(100)$ wafers by APCVD. The poly 3C-SiC surface was polished by using CMP(chemical mechanical polishing) process and then oxidized by wet-oxidation process, and finally removed SiC oxide layers. A TiW thin film as a metalization process was deposited on the surface treated poly 3C-SiC layer and was annealed through a RTA(rapid thermal annealing) process. TiW/poly 3C-SiC was investigated to get mechanical, physical, and electrical characteristics using SEM, XRD, XPS, AFM, optical microscope, I-V characteristic, and four-point probe, respectively. Contact resistivity of the surface treated 3C-SiC was measured as the lowest $1.2{\times}10^{-5}{\Omega}cm^2$ at $900^{\circ}C$ for 45 sec. Therefore, the surface treatments of poly 3C-SiC are necessary to get better contact resistance for extreme environment MEMS applications.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.342.1-342.1
• /
• 2014

The electrical, optical and structural properties of Ti doped $In_2O_3$ (TIO) ohmic contacts to p-type GaN were investigated using linear facing target sputtering (LFTS) system. Sheet resistance and resistivity of TIO films are decreased with increasing rapid thermal annealing (RTA) temperature. Although the $400^{\circ}C$ and $500^{\circ}C$ annealed samples showed rectifying behavior, the $600^{\circ}C$ and $700^{\circ}C$ annealed samples showed linear I-V characteristics indicative of the formation of an ohmic contact between TIO and p-GaN. The annealing of the contact at $700^{\circ}C$ resulted in the lowest specific contact resistivity of $9.5{\times}10^{-4}{\Omega}cm^2$. Based on XPS depth profiling and synchrotron X-ray scattering analysis, we suggested a possible mechanism to explain the annealing dependence of the properties of TIO layer on rapid thermal annealing temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.1
• /
• pp.290-293
• /
• 2003

Ohmic contact characteristics of Al ion implanted n-type SiC wafer were investigated. Al ions implanted with high dose to obtain the final concentration of $5{\times}10^{19}/cm^3$, then annealed at high temperature. Firstly, B ion ion implanted p-well region were formed which is needed for fabrication of SiC devices such as DIMOSFET and un diode. Secondly, Al implanted high dose region for ohmic contact were formed. After ion implantation, the samples were annealed at high temperature up to $1600^{\circ}C\;and\;1700^{\circ}C$ for 30 min in order to activate the implanted ions electrically. Both the inear TLM and circular TLM method were used for characterization. Ni/Ti metal layer was used for contact metal which is widely used in fabrication of ohmic contacts for n-type SiC. The metal layer was deposited by using RF sputtering and rapid thermal annealed at $950^{\circ}C$ for 90sec. Good ohmic contact characteristics could be obtained regardless of measuring methods. The measured specific contact resistivity for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$ were $1.8{\times}10^{-3}{\Omega}cm^2$, $5.6{\times}10^{-5}{\Omega}cm^2$, respectively. Using the same metal and same process of the ohmic contacts in n-type SiC, it is found possible to make a good ohmic contacts to p-type SiC. It is very helpful for fabricating a integrated SiC devices. In addition, we obtained that the ratio of the electrically activated ions to the implanted Al ions were 10% and 60% for the samples annealed at $1600^{\circ}C\;and\;1700^{\circ}C$, respectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.432.1-432.1
• /
• 2016

We demonstrated that the power conversion efficiency (PCE) of bilayer solar cell was significantly enhanced by inserting interfacial layer between the organic bilayer film and the Al electrode. Moreover, the water contact angle shows that the bilayer solar cells suffer from the undesirable surface component which limits the charge transport to the Al electrode. The AFM measurement has revealed that the pre- and post-thermal annealing treatments results in different morphologies of the interfacial layer which is critical for the higher PCE of the bilayer solar cells. Furthermore we have investigated the electrical properties of the bilayer solar cells and obtained insights into the detailed device mechanisms. The transient photovoltage measurements suggests that the significantly enhanced Voc is caused by reducing the recombination at the interface between the organic films and the Al electrode. By inserting the TiO2 layer between the bilayer film and Al electrode, the open circuit voltage (Voc) was increased from 0.37 to 0.66V. Consequently, the power conversion efficiency (PCE) of bilayer solar cells was significantly enhanced from 1.23% to 3.71%. As the results, the TiO2 interfacial layer can be used to form an ohmic contact layer, serveing as a blocking layer to prevent the penetration of the Al, and to reduce the recombination at the interface.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.292-292
• /
• 2014

Wide band gap semiconductors, such as III-nitrides (GaN, AlN, InN, and their alloys), SiC, and diamond are expected to play an important role in the next-generation electronic devices. Specifically, GaN-based high electron mobility transistors (HEMTs) have been targeted for high power, high frequency, and high temperature operation electronic devices for mobile communication systems, radars, and power electronics because of their high critical breakdown fields, high saturation velocities, and high thermal conductivities. For the stable operation, high power, high frequency and high breakdown voltage and high current density, the fabrication methods have to be optimized with considerable attention. In this study, low ohmic contact resistance and smooth surface morphology to AlGaN/GaN on 2 inch c-plane sapphire substrate has been obtained with stepwise annealing at three different temperatures. The metallization was performed under deposition of a composite metal layer of Ti/Al/Ni/Au with thickness. After multi-layer metal stacking, rapid thermal annealing (RTA) process was applied with stepwise annealing temperature program profile. As results, we obtained a minimum specific contact resistance of $1.6{\times}10^{-7}{\Omega}cm2$.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.205-208
• /
• 2001

Schottky barrier diodes are fabricated on a intrinsic GaN(4${\mu}{\textrm}{m}$) epitaxial structure grown by rf plasma molecular beam epitaxy (MBE) on sapphire substrates. First, We make Ohmic electrodes (Ti/Al/Ti/Au) by evaporator. Next, we contact RuO$_2$ by dipping in the solution (RuCl$_3$.HClO$_4$), and then we deposit Ni/Au on the surface of RuO$_2$ by evaporator. We study the electrical characteristics of GaN Schottky barrier diodes made by these methods. Measurements are C-V, I-V, SEM, EDX, and XRD for the characteristics of devices. Thickness of RuO$_2$ layer depends on supplied voltage and dipping time. Device of thinner RuO$_2$ layer have a good Schottky characteristics compare with device of thicker RuO$_2$ layer