• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1359-1366
• /
• 2010

Recently, many electronic control techniques for vehicles have been developed and applied. One of the technologies can be X-by-wire such as throttle-by-wire, brake-by-wire, steer-by-wire, and etc, in which most of mechanical parts are replaced into electrical wire and actuators. In this study, the effect of throttle-by-wire and brake-by-wire control systems on vehicle velocity control, especially in a school zone, are taken into consideration. The number of accidents reported in school zones is higher than that in other places. The reason for this is that many vehicle drivers do not obey speed limit regulations. Moreover, some of the students are careless while crossing the streets. Therefore, in this study, we attempt to develop a method using throttle-by-wire and brake-by-wire control systems for automatically reducing the vehicle speed such that it will be within the speed limit. First, an engine model and a transmission system model are developed for a specific vehicle model. Second, speed reduction is carried out such that the reduction follows a pre-designed cubic spline trajectory; the trajectory is determined such that rapid deceleration, which causes discomfort to the driver and passengers, can be prevented, for which a fuzzy-PID control algorithm is applied for the trajectory following control. Finally, simulation results are presented to verify the performance of the proposed speed reduction control system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.92-101
• /
• 1996

In a gasoline engine, the characteristics of air flow is very important not only for the design of the intake system geometry bout also for the accurate measurement of the induction air mass. In this study, an air flow rate measurement of the induction air mass. In this study, an air flow rate measurement was conducted by using the hot wire flow meter at the upstream of the intake port and the throttle. At the upstream of the throttle, the overshoot phenomena of the air flow rate by fast throttle opening were analyzed with choked flow. At the upstream of the intake port, the cylinder variation of the air flow rate and the difference between fast throttle opening and closing were showed during the unsteady state by the throttle step change. The results of this study can be used for the design of the throttle valve geometry and cylinder by cylinder control.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.2
• /
• pp.8-14
• /
• 2012

"Throttle-by-Wire" is an electronic throttle system in which mechanical cables and hydraulics are replaced by a fieldbus network, electric motors and sensors. It is crucial for an electronic throttle to design a controller that can offer an accurate and fast reference tracking performance in the presence of nonlinearities, such as friction in the gearbox and "limp-home" nonlinearity. This paper presents a nonlinear dynamic inversion based control algorithm for electronic throttle systems. Using the proposed method, the specified control performance can be achieved by canceling inherent nonlinear characteristics of the electronic throttle system. The control performance is investigated through a set of simulation results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.113-119
• /
• 2005

The passenger car drivers want in general to feel good driveability, but they sometimes feel uncomfortable by shock and jerk phenomenon when they push or release acceleration pedal with clutch engaged. In this paper, the shock and jerk characteristics are studied on the vehicles of the throttle-by-wire system. With this system, the throttle is not directly controlled by drivers but via a microprocessor. So the control logic of the throttle is very important on tip-in and tip-out driveability. Experiments were carried out on two vehicles which show different control characteristics. The torque control logics were analyzed by measuring cylinder pressures. The results show that special torque control logic is needed at tip-in/out state for good driveability.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.602-607
• /
• 2004

Accurate and quick positioning of the throttle valve in driving situation is required to implement the Traction Control System(TCS). Also, unlike a conventional throttle valve which is connected to the accelerator directly by a wire, an Electronic Throttle Valve(ETV) is driven by a DC motor and can move dependently upon the accurate position of the accelerator. In the research, the Electronic Throttle Body(ETB) and Controller for TCS application was developed. In order to drive the DC motor, the developed controller was built and interfaced to the ECU and ETB. The PID position control algorism and developed systems are designed to realize the robust tracking control of the ETV. Actual vehicle tests with these systems and PID position control algorithm. Finally, the performance of the proposed those are evaluated with the experimental studies.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.116.1-116
• /
• 2001

In the near future, drive-by-wire systems will replace mechanical systems of vehicles. Since there would be no mechanical redundancy in the x-by-wire subsystem, it needs to improve the reliability of the system using fault diagnosis of sensors and actuators. This paper proposes a Kalman filter based fault diagnosis method for the vehicle with the drive-by-wire system, which includes steer-by-wire, brake-by-wire and throttle-by-wire systems. We will show that the proposed method is successful in fault detection and isolation for single sensor/actuator faults of the vehicle system.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.1-12
• /
• 1997

In an SI engine, the characteristics of the air flow is important not only for the design of the intake system geometry but also for the accurate measurement of the induction air mass. In this study, an air flow rate measurement using the ultrasonic flow meter and hot wire flow meter was conducted at the upstream of the intake port and the throttle. At the upstream of the intake port, the pulsating flow into the cylinder affected by the pressure wave was detected directly with the flow meters instead of pressure sensors. At the upstream of the throttle, the reverse flow phenomena were showed by comparing the flow pattern measured by the hot wire air flow meter and the ultrasonic air flow meter. The results of this study can be used for the analysis of the tuning effect in the intake manifold and estimation of the error in real time measurement for the air flow rate.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.151-157
• /
• 2006

The passenger car drivers want in general to feel good driveability, but they sometimes feel uncomfortable by shock and jerk phenomena when they push or release acceleration pedal with clutch on state. In this paper, the shock and jerk characteristics are studied on the vehicles controlled by the throttle-by-wire system. Experiments and simulations were carried out on two vehicles which show different control characteristics. The engine torque control characteristics was analyzed by measuring cylinder pressure. Various specification factors of the vehicles and the torque control logic of the engines were simulated through experimental data basis. The result shows the spring effect of the trans-axle in the drive-train is one of the most important factors of the shock-jerk phenomena and the engine torque control method is also responsible for the reducing the shock-jerk amplitude. In this paper a new control logic of the engine torque is suggested for the better driveablility on the tip-in/out event.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2081-2089
• /
• 1997

Accurate positioning of the throttle valve of a gasoline engine is required to implement various systems such as traction control system(TCS), cruise control system and drive-by-wire system. In this research, position control system has been developed for the throttle actuator system that uses one throttle actuation for small volume and DC servo motor for fast response. In order to drive the DC motor, PWM signal generator and PWM amplifier were built and interfaced to the motor and controller. Also, time delay control(TDC) law has been used as a basic control algorithm. A method of varying the reference model of the TDC according to the size of change in target throttle angle is proposed here. The simulation and experimental results show that both overshoot prevention and fast response are achieved by the TDC technique with this variable reference model.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.637-638
• /
• 2008

최근 하이브리드 전기자동차의 관심이 높아짐에 따라 전기적 신호의 연결로 구동 시스템을 구성하는 X-by-wire기술 연구가 활발하게 이루어지고, 있다. 그 중 Drive시스템을 관장하는 Throttle-by-Wire 기술의 일환으로 ETC(Electronic Throttle Control)장치에 대한 연구가 진해되고 있으며, 일부 제품이 출시되고 있다. ETC 구성요소 중 가장 핵심인 모터 설계를 위해 본 논문에서는 우수한 성능을 가지는 BLDC 모터를 선택하고, 기초 설계를 통해 그 형상을 설계하였으며, 보다 더 높은 효율과 출력 토크를 얻기 위해 회전자 영구자석의 재질과 형상을 변화시키며 효율과 출력 토크에 미치는 영향을 살펴보았다.