• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.3
• /
• pp.355-364
• /
• 2013

Respect to the input AC voltage and output DC voltage, conventional three-phase PWM rectifier is classified as the voltage type rectifier with boost capability and the current type rectifier voltage with buck capability. Conventional PWM rectifier can not at the same time the boost and buck capability and its bridge is weak in the shoot- through state. These problems can be solved by Z-source PWM rectifier which has all characteristic of voltage and current type PWM rectifier. By shoot-through duty ratio control, the Z-source PWM rectifier can buck and boost at the same time, also, there is no need to consider the dead time. This paper proposes the input AC voltage sensorless control method of a three-phase Z-source PWM rectifier in order to accomplish the unity input power factor and output DC voltage control. The proposed method is estimated the input AC voltage by using input AC current and output DC voltage, hence, the sensor for the input AC voltage detection is no needed. comparison of the estimated and detected input AC voltage, estimated phase angle of the input voltage, the output DC voltage response for reference value, unity power factor, FFT(Fast Fourier Transform) of the estimated voltage and efficiency are verified by PSIM simulation.

• Journal of the Ergonomics Society of Korea
• /
• v.17 no.3
• /
• pp.61-70
• /
• 1998

The purpose of this paper is to evaluate the input methods of the numeric keypads that are widely used in various types of consumer and industrial electronic products. Three methods to enter numerals using keypads were compared: (1) Machine Intelligence, (2) + 100 key, and (3) Enter key input methods. Experiments were conducted to compare these three input methods for the channel selection of TV. Experimental prototypes which simulate TV user interfaces were developed using $RAPID^{TM}$ for usability testings. In the experiment, data on subject performance such as completion time, operational errors, and user interaction were collected through auto-logging method and video recording. After each test session, subjective preference was also asked using a questionnaire. In order to analyze the type of operation errors and the error causation, operation sequences were analyzed from the collected data. The Enter key input method showed better performance than other input methods. Based on these results. we can conclude that the input method using numeric keypads should be compatible with generic number counting(to input ch 7, it would be better to input 7 directly than to input 07 or 007) and should switch the channel as quickly as possible. This conclusion can be applied to the design of user interfaces which require numeral inputs.

• Structural Engineering and Mechanics
• /
• v.51 no.2
• /
• pp.315-331
• /
• 2014

The present study investigated the effect of the correlation of the measured road roughness profiles corresponding to the left and right wheels of a vehicle on the vibration of a vehicle-bridge coupling system. Four sets of road roughness profiles were measured by a laser road-testing vehicle. A correlation analysis was carried out on the four roughness samples, and two samples with the strongest correlation and weakest correlation were selected for the power spectral density, autocorrelation and cross-correlation analyses. The scenario of a three-axle truck moving across a rigid-frame arch bridge was used as an example. The two selected road roughness profiles were used as inputs to the vehicle-bridge coupling system. Three different input modes were adopted in the numerical analysis: (1) using the measured road roughness profile of the left wheel for the input of both wheels in the numerical simulation; (2) using the measured road roughness profile of the right wheel for both wheels; and (3) using the measured road roughness profiles corresponding to left and right wheels for the input corresponding to the vehicle's left and right wheels, respectively. The influence of the three input modes on the vibration of the vehicle-bridge system was analyzed and compared in detail. The results show that the correlation of the road roughness profiles corresponding to left and right wheels and the selected roughness input mode both have a significant influence on the vibration of the vehicle-bridge coupling system.

• Journal of the Korea Safety Management & Science
• /
• v.11 no.1
• /
• pp.121-130
• /
• 2009

This paper considers a six sigma project for reducing the cost copper of the cable materials in a electric wire company. The project follows a disciplined process of five macro phases: define, measure, analyze, improve, and control (DMAIC). A process map is used to identify process input variables. Three key process input variables are selected by using an input variables are selected by using an input variable evaluation table: large cable, plating, and a twisted pair. DOE is utilized for finding the optimal process conditions of the three key process input variables. The implementing result of this six sigma project is enable for reducing of the 2.8% copper materials.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.925-935
• /
• 2016

This paper proposes a new interleaved double-input three-level Boost (DITLB) converter, which is composed of two boost converters indirectly in series. Thus, a high voltage gain, together with a low component stress and a small input current ripple due to the interleaved control scheme, is achieved. The operating principle of the DITLB converter under the individual supplying power (ISP) and simultaneous supplying power (SSP) mode is analyzed. In addition, closed-loop control strategies composed of a voltage-current loop and a voltage-balance loop, have been researched to make the converter operate steadily and to alleviate the neutral-point imbalance issue. Experimental results verify correctness and feasibility of the proposed topology and control strategies.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1990.04a
• /
• pp.272-288
• /
• 1990

The uncertainty quantification process in probabilistic Risk Assessment usually involves a specification of the uncertainty in the input data and the propagation of this uncertainty to the final risk results. The distributional sensitivity analysis is to study the impact of the various assumptions made during the quantification of input parameter uncertainties on the final output uncertainty. The uncertainty importance of input parameters, in this case, should reflect the degree of changes in the whole output distribution and not just in a point estimate value. A measure of the uncertainty importance is proposed in the present paper. The measure is called the distributional sensitivity measure(DSM) and explicitly derived from the definition of the Kullback's discrimination information. The DSM is applied to three typical discrimination information. The DSM is applied to three typical cases of input distributional changes: 1) Uncertainty is completely eliminated, 2) Uncertainty range is increased by a factor of 10, and 3) Type of distribution is changed. For all three cases of application, the DSM-based importance ranking agrees very well with the observed changes of output distribution while other statistical parameters are shown to be insensitive.

• 제어로봇시스템학회:학술대회논문집
• /
• 1992.10a
• /
• pp.171-175
• /
• 1992

In this paper, we derive the optimal input-constrained control law which minimizes predictive control objective function subject to input constraints. In order to obtain the closed form of control law, three suboptimal methods are proposed and evaluated by simulation.

• Research in Community and Public Health Nursing
• /
• v.15 no.1
• /
• pp.29-35
• /
• 2004

Purpose: The purpose of this study was to investigate the computer input frequency of blood glucose self testing in type2 diabetic patients, for three months. Method: 39 participants were recruited from the endocrinology outpatient department of a tertiary care hospital in an urban city. The computer input frequencies were measured by patients' log in and input of http://www.biodang.com. Glycosylated haemoglobin was determined by a high performance liquid chromatography technique and fasting blood glucose was analyzed by the glucose oxidase method. Diabetes knowledge was measured by a 19 item diabetes knowledge test. Results: The computer input frequency of before breakfast blood glucose was 33.5 for three months. The total blood glucose input frequency tended to be lower in female, aged patients, middle school graduates, those who have no spouse and job, those who have no insulin treatment, obese subjects, and hyperglycemia patients, than in their counterparts. The diabetic knowledge was positively correlated with the computer input frequency of blood glucose self testing. Conclusion: An educational program should be developed to increase the computer input frequency of blood glucose self testing in type2 diabetic patients.

• Journal of Convergence for Information Technology
• /
• v.9 no.9
• /
• pp.38-43
• /
• 2019

In this paper, a method of inputting one analog input and two digital switch inputs by using one analog port of microcontroller embedded in IoT device was proposed. In this method, the upper limit and the lower limit of the input voltage range of the analog input port are determined, and the analog input voltage is input to this interval. The digital switches are configured to exceed the boundaries of the upper and lower limits, respectively. To verify the performance of the proposed method, an experimental circuit was constructed and tested using a microcontroller. As a result, all three inputs can be sensed using a single analog port, thus confirming that the three required input ports are reduced to one input port, ie, 33%.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.2
• /
• pp.142-149
• /
• 2009

This paper investigates operating characteristics of three-phase matrix converter with unity input power factor by direct duty-ratio pulse-width modulation in the case of balanced and unbalanced load. It can be found from the system analysis that (1) The control algorithm for unity power factor is not related to the variables of load sides but the input voltages, (2) With the balanced three-phase load except for the pure reactive load, the unity input power factor can be achieved, (3) In the case of the unbalanced linear load, the equivalent input characteristics of the matrix converter can be seen like the nonlinear resister, (4) When the input frequency and the output frequency have the specific relationship, each input phases have the same sharing of the average power. The feasibility and validity of the analysis were verified by simulation and experimental results.