• Transactions on Electrical and Electronic Materials
• /
• v.4 no.6
• /
• pp.13-16
• /
• 2003

Mn-doped $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin film phosphors have been grown using a pulsed laser deposition technique under various growth conditions. The structural characterization carr~ed out on a series of $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) films grown on MgO(l00) substrates usmg Zn-rich ceramic targets. Oxygen pressure was varied from 50 to 200 mTorr and Zn/Ga ratio was the function of oxygen pressure. XRD patterns showed that the lattice constants of the $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin film decrease with the substitution of sulfur and selenium for the oxygen in the $ZnGa_2O_4$. Measurements of photoluminescence (PL) properties of $ZnGa_{2}O_{4}$:$Mn^{2+}$ (M=S, Se) thin films have indicated that MgO(100) is one of the most promised substrates for the growth of high quality $ZnGa_2O_{4-x}M_{x}$:$Mn^{2+}$ (M=S, Se) thin films. In particular, the incorporation of Sulfur or Selenium into $ZnGa_2O_4$ lattice could induce a remarkable increase in the intensity of PL. The increasing of green emission intensity was observed with $ZnGa_2O_{3.925}Se_{0.075}:$Mn^{2+}$ and $ZnGa_2O_{3.925}S_{0.05}$:$Mn^{2+}$ films, whose brightness was increased by a factor of 3.1 and 1.4 in comparison with that of $ZnGa_{2}O_{4}$:$Mn^{2+}$ films, respectively. These phosphors may promise for application to the flat panel displays.

• Korean Journal of Materials Research
• /
• v.30 no.5
• /
• pp.262-266
• /
• 2020

In this paper, we investigated the effect of the passivation stack with Al₂O₃, hydrogenated silicon nitride (SiN_x:H) stack and Al₂O₃, silicon oxynitride (SiON_x) stack in the n type bifacial solar cell on monocrystalline silicon. SiNx:H and SiON_x films were deposited by plasma enhanced chemical vapor deposition on the Al₂O₃ thin film deposited by thermal atomic layer deposition. We focus on passivation properties of the two stack structure after laser ablation process in order to improve bifaciality of the cell. Our results showed SiN_x:H with Al₂O₃ stack is 10 mV higher in implied open circuit voltage and 60 ㎲ higher in minority carrier lifetime than SiON_x with Al₂O₃ stack at Ni silicide formation temperature for 1.8% open area ratio. This can be explained by hydrogen passivation at the Al₂O₃/Si interface and Al₂O₃ layer of laser damaged area during annealing.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.06a
• /
• pp.115-127
• /
• 1999

The charged clusters or particles, which contain hundreds to thousands of atoms or even more, are suggested to form in the gas phase in the thin film processes such as CVD, thermal evaporation, laser ablation, and flame deposition. All of these processes are also used in the gas phase synthesis of the nanoparticles. Ion-induced or photo-induced nucleation is the main mechanism for the formation of these nanoclusters or nanoparticles inthe gas phase. Charged clusters can make a dense film because of its self-organizing characteristics while neutral ones make a porous skeletal structure because of its Brownian coagulation. The charged cluster model can successfully explain the unusual phenomenon of simultaneous deposition and etching taking place in diamond and silicon CVD processes. It also provides a new interpretation on the selective deposition on a conducting material in the CVDd process. The epitaxial sticking of the charged clusters on the growing surface is gettign difficult as the cluster size increases, resulting in the nanostructure such as cauliflowr or granular structures.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.3
• /
• pp.289-294
• /
• 1999

The charged clusters or particles, which contain hundreds to thousands of atoms or even more, are suggested to from in the gas phase in the thin film processes such as CVD, thermal evaporation, laser ablation, and flame deposition. All of these processes are also phase synthesis of the nanoparticels. Ion-induced or photo-induced nucleation is the main mechanism for the formation of these nanoclusters or nanoparticles in the gas phase. Charge clusters can make a dense film because of its self-organizing characteristics while neutral ones make a porous skeletal structure because of its Brownian coagulation. The charged cluster model can successfully explain the unusual phenomenon of simultaneous deposition and etching taking place in diamond and silicon CVD processes. It also provides a new interpretation on the selective deposition on a conducting material in the CVD process. The epitaxial sticking of the charged clusters on the growing surface is getting difficult as the cluster size increases, resulting in the nanostructure such as cauliflower or granular structures.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.4
• /
• pp.24-31
• /
• 2005

A plused laser ablation deposition(PLAD) technique has been used for producing fine particle as well as thin film at relatively low substrate temperatures. However, in order to manufacture and evaluate such materials in detail, motions of plume particles generated by laser ablation have to be understood and interactions between the particles by ablation and gas plasma have to be clarified. Therefore this paper was focused on the understanding of plume motion in laser ablation assisted by hi plasmas at 100[mTorr]. One-dimensional hybrid model consisting of fluid and particle models was developed and three kinds of plume particles which are carbon atom(C), $ion(C^+)$ and electron were considered in the calculation of particle method. It was obtained that ablated $C^+$ was electrically captured in Ar plasmas by strong electric field(E). The difference between motions of the ablated electrons and $C^+$ made E strong and the collisional processes active. The energies of plume particles were investigated on a substrate surface. In addition the plume motion in Ar gas was also calculated and discussed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.1
• /
• pp.58-63
• /
• 2005

PTFE (polytetrafluoroethylene) thin films were prepared from the pellets of the graphite doped PTFE via pulsed laser ablation with 1064 nm Nd:YAG laser. The graphite powder converts the absorbed photon energy into thermal energy which is transmitted to nearby PTFE. The PTFE is decomposed by thermal process. The deposited films were transparent and crystalline. SEM (scanning electron microscopy) and AFM (atomic force microscopy) analyses indicated that the film surface morphology changed to fibrous structure with increasing thickness. The fluorine to carbon ratios of the film were 1.7 and molecular axis was parallel with (100) Si-wafer substrate. These results obtained by XPS (X-ray photoelectron spectroscopy), FTIR (fourier transform infrared spectroscopy) and XRD (X-ray diffraction).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.2
• /
• pp.133-137
• /
• 1998

$(Pb_{0.72}La_{0.28})Ti_{0.93}O_3(PLT(28))$ thin films were fabricated by pulsed laser deposition. PLT films deposited on $Pt/Ti/SiO_2/Si$ at $600^{\circ}C$ had a preferred orientation in (111) plane and at $550^{\circ}C$ had a (100) preferred orientation. We found that (111) preferred oriented films had well grown normal to substrate surface. This PLT(28) thin films of $1{\mu}m$ thickness had dielectric properties of ${\varepsilon}_r$=1300, dielectric $loss{\fallingdotseq}0.03 $. and had charge storage density of 10 [${\mu}C/cm^2$] and leakage current density of less than $10^{-6}[A/cm^2]$ at 100[kV/cm]. These results indicated that the PLT(28) thin films fabricated by pulsed laser deposition are suitable for DRAM capacitor application.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.105-112
• /
• 2018

This paper proposes a method for fabricating heatable glass using the conduction characteristics of metal thin films deposited on the surface of Low-e(Low emissivity) glass. The heating value of Low-e glass depends on the Joule heat caused by Low-e glass sheet resistance. Hence, its prediction and design are possible by measuring the sheet resistance of the material. In this study, silver electrodes were placed at 50 mm intervals on a soft Low-e glass sample with a low emissivity layer of 11 nm. This study measured the sheet resistance using a 4-point probe, predicted the power consumption and heating value of the Low-e glass, and confirmed the heating performance through fabrication and experience. There are two conventional methods for manufacturing heatable glass. One is a method of inserting nichrome heating wire into normal glass, and the other is a method of depositing a conductive transparent thin film on normal glass. The method of inserting nichrome heating wire is excellent in terms of the heating performance, but it damages the transparency of the glass. The method for depositing a conductive transparent thin film is good in terms of transparency, but its practicality is low because of its complicated process. This paper proposes a method for manufacturing heatable glass with the desired heating performance using Low-e glass, which is used mainly to improve the insulation performance of a building. That is by emitting a laser beam to the conductive metal film coated on the entire surface of the Low-e glass. The proposed method is superior in terms of transparency to the conventional method of inserting nichrome heating wire, and the manufacturing process is simpler than the method of depositing a conductive transparent thin film. In addition, the heat characteristics were compared according to the patterning of the surface thin film of the Low-e glass by an emitting laser and the laser output conditions suitable for Low-e glass.

• Korean Journal of Materials Research
• /
• v.4 no.4
• /
• pp.401-405
• /
• 1994

The chemical composition and electrical properties were investigated for epitaxially crystallized $(Ba_{0.5}Sr_{0.5})Tio_3$ (BST) films deposited on Pt and $YBa_Cu_3O_{7-x}$(YBCO) electrodes by laser ablation technique. The crystalline quality of the heteroepitaxial BST films deposited on Pt bottom electrode was found to be better than that of BST film on YBCO electrode by the RBS analysis. Films deposited at $600^{\circ}C$ on Pt electrode showed a dielectric constant of 320 and a dissipation factor of 0.023 at 100kHz. Leakage current density of BST films on Pt electrode was smaller than that on YBCO bottom electrode. Their leakage current density was about 0.8$\mu \; A/ \textrm{cm}^2$ at an applied electric field of 0.15MV/cm.

• ETRI Journal
• /
• v.37 no.6
• /
• pp.1135-1142
• /
• 2015

Multilayered ZnO-$SnO_2$ heterostructure thin films consisting of ZnO and $SnO_2$ layers are produced by alternating the pulsed laser ablation of ZnO and $SnO_2$ targets, and their structural and field-effect electronic transport properties are investigated as a function of the thickness of the ZnO and $SnO_2$ layers. The performance parameters of amorphous multilayered ZnO-$SnO_2$ heterostructure thin-film transistors (TFTs) are highly dependent on the thickness of the ZnO and $SnO_2$ layers. A highest electron mobility of $43cm^2/V{\cdot}s$, a low subthreshold swing of a 0.22 V/dec, a threshold voltage of 1 V, and a high drain current on-to-off ratio of $10^{10}$ are obtained for the amorphous multilayered ZnO(1.5nm)-$SnO_2$(1.5 nm) heterostructure TFTs, which is adequate for the operation of next-generation microelectronic devices. These results are presumed to be due to the unique electronic structure of amorphous multilayered ZnO-$SnO_2$ heterostructure film consisting of ZnO, $SnO_2$, and ZnO-$SnO_2$ interface layers.