• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.43-47
• /
• 1996

$RuO_2$ thin films deposited directly on Si substrate by RF magnetron sputtering method using $RuO_2$ target have been investigated. Special interest was focused on the effect of process parameter on the surface roughness of $RuO_2$ films. Crystallization behavior and electrical properties of the films deposited at $300^{\circ}C$ were superior to those deposited at room temperature. Metallic Ru phase was formed in pure Ar and this phase had resulted poor adhesion after post annealing process in oxidizing ambient. Microstructural analysis reveals that the size of the $RuO_2$ crystallites gets smaller and the surface becomes smoother as the $O_2$ partial pressure or film thickness decreases. Irrespective of the $O_2/Ar$ ratio, resistivity of $RuO_2$ films ranged in $50~70 {\mu}{\Omega}-cm$. As the film thickness decreases, there is a thickness where the resistivity rises abruptly. Such an onset thickness turned out to be dependent n the $O_2$/Ar ratio.

• International Journal of High-Rise Buildings
• /
• v.9 no.4
• /
• pp.361-368
• /
• 2020

The authors developed a new type of steel slit shear wall (SSSW) having the function of structural condition assessment through visually inspecting the out-of-plane deformation of the designed tapered links subjected to lateral deformation. To facilitate its practical application, this paper studies how to design dimensions of the tapered links. Two parameters, the width-to-thickness ratio of the tapered links and steel yield stress, were studied. The performance of structural condition assessment was affected by both parameters with the width-to-thickness ratio being the controlling one. Through both numerical and experimental study, the designed width-to-thickness ratio of tapered links for different levels of structural condition assessment was established considering the effect of different steel grades used. In practice, the dimensions of tapered links can be determined following the design equation provided. Finally, a design procedure for the proposed SSSW system is provided.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.10
• /
• pp.2305-2309
• /
• 2010

In this paper, the variations of threshold voltage characteristics for ratio of channel length and thickness have been alanyzed for DG(Double Gate)MOSFET having top gate and bottom gate. Since the DGMOSFET has two gates, it has advantages that contollability of gate for current is nearly twice and SCE(Short Channel Effects) shrinks in nano devices. The channel length and thickness in MOSFET determines device size and extensively influences on SCEs. The threshold voltage roll-off, one of the SCEs, is large with decreasing channel length. The threshold voltage roll-off and drain induced barrier lowing have been analyzed with various ratio of channel length and thickness for DGMOSFET in this study.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.765-767
• /
• 2010

In this paper, the variations of threshold voltage characteristics for ratio of channel length and thickness have been alanyzed for DG(Double Gate)MOSFET having top gate and bottom gate. Since the DGMOSFET has two gates, it has advantages that contollability of gate for current is nearly twice and SCE(Short Channel Effects) shrinks in nano devices. The channel length and thickness in MOSFET determines device size and extensively influences on SCEs. The threshold voltage roll-off, one of the SCEs, is large with decreasing channel length. The threshold voltage roll-off has been analyzed with various ratio of channel length and thickness for DGMOSFET in this study.

• Journal of Crop Science and Biotechnology
• /
• v.11 no.2
• /
• pp.151-156
• /
• 2008

The objective of this study is to identify main-effect QTLs, epistatic QTLs, and the interactions between QTL and the environment associated with grain appearances of brown rice. A genetic linkage map was created with 172 DNA markers spanning 12 rice chromosomes based on 120 DH lines, which derived from a cross between 'Samgang'(Tongil) and 'Nagdong'(Japonica). One thousandgrain weight, length, width, length-to-width ratio, and thickness were evaluated regarding the DH population. Twenty independent QTLs and fourteen epistatic QTLs were identified in using CIM by two programs, known as WinQTLcart2.5 and QTLMAPPER. The QTLs of qgw9.1 in an interval of RM434-RM242 on chromosome 9 and qgw11.1 at a peak marker of RM287 on chromosome 11 for one thousand-grain weight, qgwi2.2 for grain width at a peak marker of RM450, qlw2.1 for length-to-width ratio flanked by RM492 and RM324, and qgt2.1 for thickness flanked by 2009 and RM492 on chromosome 2 were detected over two years, which can be considered as stable QTLs. The epistatic effect might be an important component for genetic basis of one thousand-grain weight and width. The main-effect QTLs of grain width and length to width ratio were easily influenced by environments.

• Steel and Composite Structures
• /
• v.20 no.6
• /
• pp.1391-1409
• /
• 2016

Masonry infill has a significant effect on stiffness contribution, strength and ductility of masonry-infilled frames. These effects may cause damage of weak floor, torsional damage or short-column failure in structures. This article presents experiments of 1/2.5-scale steel reinforced recycled aggregates concrete (SRRC) frames. Three specimens, with different infill rates consisted of recycled concrete hollow bricks (RCB), were subjected to static cyclic loads. Test phenomena, hysteretic curves and stiffness degradation of the composite structure were analyzed. Furthermore, effects of axial load ratio, aspect ratio, infill thickness and steel ratio on the share of horizontal force supported by the frame and the infill were obtained in the numerical example.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.5
• /
• pp.992-997
• /
• 2016

This paper analyzes the deviation of tunneling current for the ratio of top and bottom gate oxide thickness of short channel asymmetric double gate(DG) MOSFET. The ratio of tunneling current for off current significantly increases if channel length reduces to 5 nm. This short channel effect occurs for asymmetric DGMOSFET having different top and bottom gate oxide structure. The ratio of tunneling current in off current with parameters of channel length and thickness, doping concentration, and top/bottom gate voltages is calculated in this study, and the influence of tunneling current to occur in short channel is investigated. The analytical potential distribution is obtained using Poisson equation and tunneling current using WKB(Wentzel-Kramers-Brillouin). As a result, tunneling current is greatly changed for the ratio of top and bottom gate oxide thickness in short channel asymmetric DGMOSFET, specially according to channel length, channel thickness, doping concentration, and top/bottom gate voltages.

• Korean Journal of Metals and Materials
• /
• v.50 no.3
• /
• pp.212-217
• /
• 2012

This study was carried out to investigate the effect of the hot forging ratio on the microstructure and mechanical properties of ultra high carbon steel. The microstructure of ultra high carbon steel with 1.5%wt.C consisted of a proeutectoid cementite network and acicular microstructure in pearlite matrix. With increasing hot forging ratio, the volume and thickness of the network and acicular proeutectoid cementite decreased. Lamella spacing and the thickness of eutectoid cementite decreased with increasing hot forging raito, and were broken up into particle shapes, which then became spheroidized. When the forging ratio was over 65%, the network and acicula shape of the as-cast state disappeared. With increasing hot forging ratio, hardness, tensile strength, elongation and impact value were not changed up to 50%, and then rapidly increased with the increase of the forging ratio.

• Structural Engineering and Mechanics
• /
• v.64 no.5
• /
• pp.591-610
• /
• 2017

This paper is concerned with the static analysis of variable thickness of two directional functionally graded porous materials (FGPM) circular plate resting on a gradient hybrid foundation (Horvath-Colasanti type) with friction force and subjected to compound mechanical loads (e.g., transverse, in-plane shear traction and concentrated force at the center of the plate).The governing state equations are derived in terms of displacements based on the 3D theory of elasticity, assuming the elastic coefficients of the plate material except the Poisson's ratio varying continuously throughout the thickness and radial directions according to an exponential function. These equations are solved semi-analytically by employing the state space method (SSM) and one-dimensional differential quadrature (DQ) rule to obtain the displacements and stress components of the FGPM plate. The effect of concentrated force at the center of the plate is approximated with the shear force, uniformly distributed over the inner boundary of a FGPM annular plate. In addition to verification study and convergence analysis, numerical results are displayed to show the effect of material heterogeneity indices, foundation stiffness coefficients, foundation gradient indices, loads ratio, thickness to radius ratio, compressibility, porosity and friction coefficient of the foundation on the static behavior of the plate. Finally, the responses of FG and FG porous material circular plates to compound mechanical loads are compared.

• Journal of the Korean Magnetics Society
• /
• v.16 no.3
• /
• pp.173-177
• /
• 2006

We have investigated the magnetoresistance (MR) effect of the spin valve structures composed of perpendicularly magnetized Pd/Co multilayers, with changing the space layer (Pd or Cu) thickness, the stacking number of the Pd/Co multilayers, and the Co insertion-layer thickness. The Cu space layer showed larger MR ratio than the Pd space layer. The Co insertion-layer between Cu layer and pinned layer enhanced the MR ratio about three times. The maximum MR ratio of 7.4 % was established in the sample with the Co insertion-layer thickness of 0.62 and 1.01 nm.