• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.8
• /
• pp.1144-1151
• /
• 2009

Refrigeration systems can be incorporated with non-adiabatic capillary tubes to improve their efficiency. The non-adiabatic capillary tube is constructed by joining the capillary tube with suction pipe to allow heat transfer between them, which is called capillary tube-suction line heat exchanger(SLHX). There are various joining methods and they may influence the characteristics of the refrigeration cycle. The present work aims to analyze the effect of widely-used two joining methods on the refrigeration cycle. The results show that soldered SLHX has much less thermal resistance than tapered SLHX but slightly outperforms in terms of coefficient of performance(COP) and cooling capacity. The soldered SLHX increased COP and cooling capacity of a refrigerator by 5.09% and 14.77% while the tapered SLHX did by 5.05% and 14.75%, respectively.

• Applied Chemistry for Engineering
• /
• v.21 no.4
• /
• pp.440-444
• /
• 2010

$SnO_2$ powders were prepared from the calcination of stannic acids precipitated from the aqueous solution of $SnCl_4$ with ammonium nitrate as a precipitator at $90^{\circ}C$. For the comparison of properties, the stannic acids were prepared from the homogeneous precipitation method using urea as a precipitator at the same temperature. The stannic acid from ammonium nitrate at a thermal gravity analysis showed the weight loss until $700^{\circ}C$ and the percentage of total weight loss was 16.5%. The crystallization of stannic acid into $SnO_2$ finished in the calcination at $600^{\circ}C$ for 2 h. The crystallite size of $SnO_2$ increased with the increase of calcination temperature and initial concentration of $SnCl_4$ solution. In case of the same calcination condition, $SnO_2$ prepared from homogeneous precipitation using urea had a relatively smaller crystallite size rather than $SnO_2$ prepared from ammonium nitrate.

• Journal of Energy Engineering
• /
• v.22 no.4
• /
• pp.399-405
• /
• 2013

The gas motion inside the engine cylinder plays a very important role in determining the thermal efficiency of an internal combustion engine. A precise information of in-cylinder three dimensional complex gas motion is crucial in optimizing engine design. Homogeneous charge compression ignition (HCCI) engine is a combustion concept, which is a hybrid between Otto and Diesel engine. The turbulent diffusion leads to increased rates of momentum, heat and mass transfer. The in-cylinder turbulence flow was found to affect the present HCCI combustion mainly through its influence on the wall heat transfer. This study investigates the effect of piston geometry shape on the turbulent flow characteristics of in-cylinder from the numerical analysis using the LES model and the results obtained can offer guidelines of the combustion geometries for better combustion process and engine performance.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.5
• /
• pp.319-326
• /
• 2012

Han-green building is one of the modernized Korean traditional buildings developed by Korea Forest Research Institute. This building was developed to increase the competitiveness of Korean traditional building using state-of-art technologies; hence Han-green building has the inherent characteristics of traditional building such as exposed wood frame in wall. Because of discontinuity in wall by the exposed wood frame, there is a concern on heat-air leaking in terms of energy performance. In this study, air-tightness of Han-green building was evaluated to investigate the influence of gaps between frames and in-fill walls. Blower door test was carried out to evaluate the air-tightness, and air-change rate (ACH50) was evaluated by averaging four set of pressurization and depressurization test. The air-change rate of Han-green house was 5.91 $h^{-1}$. To improve energy performance of Han-green house, thermal infrared images of Han-green house were taken in winter with heating to find out where the heat loss occurred. It was found that the building lost more heat through gaps between frames and in-fill walls rather than through other parts of this building. After covering all the gaps by taping, the blower door test was performed again, and the air-change rate was improved to 5.25 $h^{-1}$. From this analysis, it was concluded that the heated air can leak through the gaps between frames and walls. Therefore, when one designs the post and beam building with exposed frame, the detail design between frame and wall needs to be carefully dealt. However, Han-green building showed relatively high air-tightness comparing with other country research results.

• Clean Technology
• /
• v.7 no.1
• /
• pp.81-88
• /
• 2001

Limestone has been used as absorbent in the FGD(Flue Gas Desulfurization) system, the DeSOx system of thermal power plant. This study investigated the desulfurization characteristics of the two different limestones, 325mesh and 200mesh particle size. Experimental analysis showed that the dissolving rate of limestone became much slower as the particle size increased. But the desulfurization efficiency depended on the L/G(liquid/gas) ratio and slurry pH regardless of the limestone particle size. The quality of gypsum produced in the FGD process increased as the limestone particle size or the slurry pH decreased. To reduce the cost of absorbent, the mixed limestone which were composed of 200 and 325mesh limestone with 5 different ratios were tested.

• Journal of the Korean Chemical Society
• /
• v.29 no.5
• /
• pp.543-551
• /
• 1985

A new class of polyhydrazones has been synthesized by the solution polycondensation from equimolecular amounts of aromatic dialdehydes such as para, meta, ortho-phthal aldehyde, 5,5'-methylene-bis-salicyl aldehyde (PPTA, MPTA, OPTA, MBSA) and dihydrazides, 5,5'-methylene-bis-salicylic dihydrazide (MBSDH), terephthalic dihydrazide (TDH), sebacic dihydrazide (SDH) in DMF-$CH_3COOH$ solution. The solubility characteristics, spectral, and thermal properties of the synthesized polyhydrazones and their metal chelates were also studied. These polyhydrazones and their metal chelates except the polyhydrazone prepared from OPTA-MBSDH were generally insoluble in common organic solvents. The thermogravimetric analysis of polyhydrazones showed 10% weight losses at 250∼350$^{\circ}$C and residual weight at 500$^{\circ}$C were 32.5∼62.5%. The decomposition temperature of higher relatively, and the metal chelates decrease in the following orders; Zn(II)-IIa > Ni(II)-IIa > Co(II)-IIa > Cu(II)-IIa.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.2
• /
• pp.212-216
• /
• 1999

SiC(3C) photodiodes (PDs) were fabricated on p-type Si(111) substrates using chemical vapor deposition (CVD) technique by pyrolyzing tetramethylsilane (TMS) with $H_{2}$ carrier gas. Electrical properties of SiC(3C) were investigated by Hall measurement and current-voltage (I-V) characteristics. SiC(3C) layers exhibited n-type conductivity. Ohmic contact was formed by thermal evaporation Al metal through a shadow-mask. The optical gain $(G_{op})$ of the SiC(3C)/Si PD was measured as a function of the incident wavelength. For the analysis of the photovoltaic detection of the Sic(3C) n/p PD, the spectral response (SR) has calculated by using the electrical parameters of the SiC(3C) layer and the geometric structure of the PD. The peak response calculated for properly chosen parameters was about 0.75 near 550 nm. We expect a good photoresponse in the SiC(3C) heterostructure for the wavelength range of 400~600 nm. The SiC(3C) photodiode can detect blue and near ultraviolet (UV) radiation.

• Fashion & Textile Research Journal
• /
• v.22 no.3
• /
• pp.386-398
• /
• 2020

This study compared dip-coating and in situ polymerization methods for the development of nanofiber-based E-textile using polypyrrole. Nanofiber webs were fabricated by electrospinning an aqueous poly (vinyl alcohol) (PVA) solution. Subsequently, the PVA nanofiber web underwent thermal treatment to improve water resistance. Dip-coating and in situ polymerization methods were used to deposit polypyrrole on the surfaces of the nanofiber web. An FE-SEM analysis was also conducted to examine specimen surface characteristics along with EDS and FT-IR that analyzed the chemical bonding between polypyrrole and specimens. The line resistance and sheet resistance of the treated specimens were measured. Finally, an electrocardiogram (ECG) was measured with textile sensors made of the polypyrrole-deposited PVA nanofiber webs. The polypyrrole-deposited PVA nanofiber webs fabricated by dip-coating dissolved in the dip-coating solution and indicated damage to the nanofibers. However, in the case of in situ polymerization, polypyrrole nanoparticles were deposited on the surface and inter-web structure of the PVA nanofiber web. The resistance measurements indicated that polypyrrole-deposited PVA nanofiber webs fabricated by in situ polymerization with an average sheet resistance of 5.3 k(Ω/□). Polypyrrole-deposited PVA nanofiber webs fabricated by dip-coating showed an average sheet resistance of 57.3 k(Ω/□). Polypyrrole-deposited PVA nanofibers fabricated by in situ polymerization showed a lower line and sheet resistance; in addition, they detected the electrical activity of the heart during ECG measurements. The electrodes made from polypyrrole-deposited PVA nanofiber webs by in situ polymerization showed the best performance for sensing ECG signals among the evaluated specimens.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.11
• /
• pp.697-704
• /
• 2016

Coal modified by acid treatment was investigated to analyze the correlation between the cell performance and electrochemical parameters in a direct carbon fuel cell (DCFC). The fuels were subjected to thermogravimetry analysis, gas adsorption test, and X-ray photoelectron spectroscopy to investigate the fuel properties and surface characteristics. After the treatment of raw coal, the thermal reactivity of the treated fuels increased, and the specific surface area decreased, though the mean pore diameters of three fuels were similar. The coal treated by $HNO_3$ showed the highest ratio of oxygen to carbon, and also an increase in the surface oxygen groups on the fuel surface. Through comparison between the fuel surface properties and electrochemical performance, it was confirmed that the surface oxygen groups have an influence on the improvement in the DCFC performance.

• Journal of the Korean housing association
• /
• v.27 no.6
• /
• pp.31-43
• /
• 2016

The purpose of this paper is to gather information and opinions to better guide the direction for implementing improvements of the senior centers' indoor environments located in Jeonju residential areas, by surveying the users about the level of satisfaction and analyzing the result in relation to the current situation. Senior centers located in Jeonju residential areas were operating the facilities with low financial support from the local autonomous entity. According to the results of the survey, most of the users tend to use the facilities between 12p.m. to 6p.m., and the majority have lunch at the senior centers. Most of the senior centers already have cooking facilities, without a dining room, except one place, and even the facilities they have are very poor. In a thermal environment area, the temperature is mostly above in summer or below in winter the appropriate temperature, especially the temperature of the restroom of all senior centers are below $20^{\circ}C$ in winter. The density of carbon dioxide is above average in most indoor areas. However, the users' level of facilities' satisfaction was positive. To improve the seniors' quality of life, the local autonomous entity has to start regular check-ups and repair of the poor indoor environment and facilities, with more financial support and active supervision by senior center the management.