• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.9
• /
• pp.1060-1067
• /
• 1988

In this paper, we have investigated the effects of rapid thermal process on the electrical and structural properties of silicon films. It was shown that required times and temperature for the successful activation of dopants (Boron, Phosphorus:5E15atoms/cm\ulcorner were above 1000\ulcorner, 10sec, respectively. The typical resistivities of films deposited below 600\ulcorner were in the range of 1.0 E-3ohm-cm which was 20-30% lower than that of initially polycrystalline silicon depositd above 600\ulcorner. After rapid thermal process at high temperature above 1000\ulcorner, the films did not reveal any change in resistivity due to the dopant segregation, and better electrical conductivity could be obtained by increasing the process time. The grain growth by RTA treatment was more salient in the case of the doped amorphous than that of initially polycrystalline. The surface of the films also preserved the higher structural perfection and surface smoothness.

• Fire Science and Engineering
• /
• v.27 no.4
• /
• pp.7-12
• /
• 2013

Recently, the risk of fire outbreak is going up because of newly developed combustible materials are intended to apply more. Especially the steel framed structure can lose its load-bearing capacity when it is exposed to higher temperature condition such as a fire. So the pre-evaluation of fire resistance of the structure is very essential that the mechanical properties of yield strength and elastic modulus and thermal properties such as conductivity and linear expansion be required. To get the databases for SM 400 or welding structural steels at high temperature, various temperature conditions were used for deriving the yield strength, elastic modulus, linear expansion, and conductivity and the results were compared to those of SS 400, ordinary structural steel, respectively.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.05a
• /
• pp.118-119
• /
• 1993

Aluminium titanate (Al$_2$TiO$_{5}$) as structural ceramics is known as a low thermal exansion, a low thermal conductivity, a low Young's modulus, and excellent thermal shock resistant material. These properities allow for the testing as an insulating material in engines for portliner, piston bottom an turbo charger. However, those composites has low mechanical strength due to the presence of microcracks developed by the large difference in thermal expansion coefficients along crystallographic directions exceed the internal strength of material and its tendency to decompose into $Al_2$O$_3$ and TiO$_2$ at temperature below 130$0^{\circ}C$ limit however the application of aluminium titanate.e.

• Journal of Korea Foundry Society
• /
• v.44 no.1
• /
• pp.3-8
• /
• 2024

Reducing industrial waste and improving the atmospheric environment recently have emerged as important tasks for the casting industry. Various types of artificial sand that can replace natural sand have been developed and used to solve problems that arise with the use of conventional foundry sand and to improve the foundry environment. However, only limited physical properties provided by overseas suppliers are known and in-depth comparative analyses with existing natural sand are lacking. For the design of the casting process, a wide range of thermal properties must be secured not only at room temperature but also at high temperatures. In addition, it is important to compare and analyze the differences in thermal properties between existing natural and artificial sand because changes in thermal properties require changes in the design of the casting method. In this study, the thermal behavior of the mold was analyzed through a thermal expansion test of mold blocks for natural and artificial sand., To this end, a thermal property test to evaluate thermal conductivity was performed by determining a temperature range. The results of the experiment, revealed that the thermal conductivity was 5-40% higher in artificial sand than in natural sand, and the coefficient of thermal expansion was about 15% lower for artificial sand. However, there was not a significant difference in specific heat regardless of the composition.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.11
• /
• pp.1600-1604
• /
• 2017

Mo-Cu alloys have been widely used for heat sink materials, vacuum technology, automobile and many other applications due to their excellent physical and electronic properties. Especially, Mo-Cu composites with 5~20 wt% copper are widely used for the heavy duty service contacts due to their excellent properties like low coefficient of thermal expansion, wear resistance, high temperature strength and prominent electrical and thermal conductivity. In most of the applications, high dense Mo-Cu materials with homogeneous microstructure are required for high performance, which has led in turn to attempts to prepare ultra-fine and well-dispersed Mo-Cu powders in different ways, such as spray drying and reduction process, electroless plating technique, mechanical alloying process and gelatification-reduction process. However, most of these methods were accomplished at high temperature (typically degree), resulting in undesirable growth of large Cu phases; furthermore, these methods usually require complicated experimental facilities and procedure. In this study, Mo-Cu alloying were prepared by planetary ball milling (PBM) and spark plasma sintering (SPS) and the effect of Cu with contents of 5~20 wt% on the microstructure and properties of Mo-Cu alloy has been investigated.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.9 no.1
• /
• pp.51-54
• /
• 2009

Transparent Cuprous oxide film was deposited by rapid thermal oxidation (RTO) of Cu at $500^{\circ}C$/45s condition on textured single-crystal n-Si substrate to form $Cu_2O$/n-Si heterojunction photodiode. The Hall effect measurements for the $Cu_2O$ films showed a p-type conductivity. The photovoltaic and electrical properties of the junction at room temperature were investigated without any post-deposition annealing. I-V characteristics revealed that the junction has good rectifying properties. The C-V data showed abrupt junction and a built-in potential of 1 V. The photodiode showed good stability and high responsivity in the visible at three regions; 525 nm, 625-700 nm, and 750nm denoted as regions A, B, and C, respectively.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.571-580
• /
• 2020

In this study, an experimental study on storage media for thermal energy storage system was conducted. For thermal energy storage medium, concrete has excellent thermal and mechanical properties and also has various advantages due to its low cost. In addition, the ultra-high strength concrete reinforced by steel fibers exhibits excellent durability against exposure to high temperatures due to its high toughness and high strength characteristics. Moreover, the high thermal conductivity of steel fibers has an advantageous effect on heat storage and heat dissipation. Therefore, to investigate the temperature distribution characteristics of ultra-high-strength concrete, concrete blocks were fabricated and a heating test was performed by applying high-temperature thermal cycles. The heat transfer pipe was buried in the center of the concrete block for heat transfer by heat fluid flow. In order to explore the temperature distribution characteristics according to different shapes of the heat transfer pipe, a round pipe and a longitudinal fin pipe were used. The temperature distribution at the differnent thermal cycles were analyzed, and the thermal energy and the cumulated thermal energy over time were calculated and analyzed for comparison based on test results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.304-304
• /
• 2006

Ternary tellurite glassy systems ($Li_2O-V_2O_5-TeO_2$) have been synthesised using Vanadium oxide as a network former and Lithium oxide as network modifier. The addition of a metal oxide makes them electric or mixed electric-ionic conductors, which are of potential interest as cathode materials for solid-state batteries. This glass-ceramics crystallized from the $Li_2O-V_2O_5-TeO_2$ system are particularly interesting, because they exhibit high conductivity (up to $5.63{\times}10^{-5}$ S/cm) at room temperature the glass samples were prepared by quenching the melt on the copper plate and the glass-ceramics were heat-treated at crystallizing temperature determined from differential thermal analysis (DTA). The electric DC conductivity result have been analyzed in terms of a small polaron-hopping model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.334-335
• /
• 2005

Ternary tellurite glassy systems ($Li_2O-V_2O_5-P_2O_5$) have been synthesised using Vanadium oxide as a network former and Lithium oxide as network modifier. The addition of a metal? oxide makes them electric or mixed electric-ionic conductors, which are of potential interest as cathode' materials for solid-state batteries. This glass-ceramics crystallized from the $Li_2O-V_2O_5-P_2O_5$ system are particularly interesting, because they exhibit high conductivity (up to $5.95\times10^{-4}$ S/cm) at room temperature. the glass samples were prepared by quenching the melt on the copper plate and the glass-ceramics were heat-treated at crystallizing temperature determined from differential thermal analysis (DTA). The electric D.C conductivity result have been analyzed in terms of a small polaron-hopping model.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.842-844
• /
• 2004

Ternary tellurite glassy systems $(CuO-V_2O_5-TeO_2)$ have been synthesised using tellurium oxide as a network former and copper oxide as network modifier. The addition of a transition-matal oxide makes them electric or mixed electric-ionic conductors, which are of potential interest as cathode materials for solid-state batteries. This glass-ceramics crystallized from the $CuO-V_2O_5-TeO_2$ system are particularly interesting, because they exhibit high conductivity ( up to $6.03{\times}10^{-3}S/cm$) at room temperature. the glass samples were prepared by quenching the melt on the copper plate and the glass-ceramics were heat-treated at crystallizing temperature determined from differential thermal analysis (DTA). The electric D.C conductivity result have been analyzed in terms of a small polaron-hopping model.