• 한국해양공학회지
• /
• 제1권1호
• /
• pp.104-110
• /
• 1987

Fatigue tests by axial loading (R = 0.05) were carried out to investigate fatigue crack growth characteristics of small surface cracks in 2 1/4 Cr-1 Mo steel at room temperature by using flat specimens with a small artificial pit. All the data of the fatigue crack growth rate obtained in the present test are determined as a function of the stress intensity factor range about a semi-elliptical crack, so that the application of linear fracture mechanics to the surface fatigue crack growth and to the fatigue crack growth into depth, and all the data obtained from tests were discussed in comparison with the data of Type 304 stainless steel and two type of mild steel under the same test conditions. The obtained results are as follows: 1)When the cycle ratios are same, surface fatigue crack length and its depth are almost same and fall within a narrow scatter band in spite of different stress levels. 2)Relations of the surface fatigue crack growth rate (da/dN) and fatigue crack growth rate into depth (db/dN) to its stress intensity factor range ($\Delta K_{Ia}, \Delta K_{Ib}$) can be plotted as a straight line at log-log diagram without dependence of stress level and coincide with the data of part-through crack in various steels.

• 한국공작기계학회논문집
• /
• 제11권6호
• /
• pp.111-117
• /
• 2002

The high quality and a nearly stoichometric growth of $Cd_{1-y} Zn_y$/Te(y＝0.04) epilayers have been successfully grown on GaAs substrate by hot wall epitaxy (HWE) by optimizing the growth condition including the preheating treatment and Cd reservoir temperature. The relationship between quality and thickness was examined and best value of FWHM from X-ray rocking curve of 121 arcsec are obtained. Also, emission peaks related to the recombination of free excitons such as the ground state and the first excited state were observed in the PL spectrum at 4.2K. The ($A^0$, X) emission related to Cd vacancy and deep level emission was not measured. These results indicated that the grown CZT/GaAs epilayer was high qualify and purity.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 춘계학술대회 논문집
• /
• pp.263-268
• /
• 1999

With HAZ of A 106 Gr B steel weldment, fatigue test in air, electrochemical polarization test and corrosion fatigue test in 3.5wt.% NaCl solution were performed changing load ratio. Obtained results are as follows. 1) K$\sub$op/ was independent of K$\sub$max/ and load ratio in fatigue crack growth. 2) In variation of load ratio, the scatter band of crack growth curve was reduced by half considering crack closure 3) In the result of electrochemical polarization test, current density was increased abruptly when potential was larger than corrosion potential. 4) Fatigue crack growth rate in corrosive environment was markly higher than the rate in air because of corrosion characteristics of the material and anodization of inner surface crack.

• Food Science and Biotechnology
• /
• 제17권6호
• /
• pp.1352-1356
• /
• 2008

Bootstrap method, a computer-intensive statistical technique to estimate the distribution of a statistic was applied to deal with uncertainty and variability of the experimental data in stochastic prediction modeling of microbial growth on a chill-stored food. Three different bootstrapping methods for the curve-fitting to the microbial count data were compared in determining the parameters of Baranyi and Roberts growth model: nonlinear regression to static version function with resampling residuals onto all the experimental microbial count data; static version regression onto mean counts at sampling times; dynamic version fitting of differential equations onto the bootstrapped mean counts. All the methods outputted almost same mean values of the parameters with difference in their distribution. Parameter search according to the dynamic form of differential equations resulted in the largest distribution of the model parameters but produced the confidence interval of the predicted microbial count close to those of nonlinear regression of static equation.

• 한국결정성장학회지
• /
• 제15권6호
• /
• pp.239-243
• /
• 2005

The effect of pH and particle size on the dispersion stability of ultra-fine $BaTiO_3$ suspensions in aqueous medium have been investigated by means of zeta potential, sediment experiments, and powder properties (particle analysis, specific surface area) etc. Zeta potential as a function of pH for two particles of different size increases from -75 to +10 mV with decreasing pH from 8.5 to 1.4. The curve of zeta potential for small particle (150 nm) has slow slope than that of large particle (900nm), giving IEP (isoelectric point) value of pH=1.6 for small particle and pH=1.9 for large particle respectively, which means that it is more difficult to control zeta potential with pH fur small particle than large particle. The dispersion stability of $BaTiO_3$ particles in aqueous medium was found to be strongly related with the agglomeration of colloidal suspensions with time through the sedimentation behaviors of colloidal particles with time and pH value.

• 한국해양공학회지
• /
• 제15권3호
• /
• pp.75-80
• /
• 2001

The elastic plastic fracture toughness of this material is evaluated by the an unloading compliance method according to the ASTM E813-97 and E1152-97 method on the smooth and side groove 1CT specimens. The effect of smooth and side groove is studied on the material tearing modulus and characterizes the crack tip field under the plane stress and strain. SG-365 steel is observed that J-R curve and Tmat value decrease as 0%, 20%, 30%, and 40%. The 40% side grooved specimen is very useful in estimation of the $J_IC$. Because it is much easier than the smooth specimen to the onset of the ductile tearing by the R curve method. Besides. it improves the accuracy of toughness values, decreases the scattering the them and tunneling and shear lip by the side groove. Applicability of tearing modulus($T_J$ proposed by paris et al as instability panameter for this material is investigated.

• 센서학회지
• /
• 제8권6호
• /
• pp.476-480
• /
• 1999

PLD 법을 이용하여 PbSe 박막을 p-Si(100) 기판 위에 성장시켰다. 성장온도에 따른 박막의 결정구조를 조사하기 위하여 기판온도를 RT${\sim}400^{\circ}C$로 변화시키면서 박막을 제작하였다. 여러 기판온도에서 제작한 PbSe 박막의 XRD 패턴과 PbSe(200) rocking curve의 반치폭(FWHM)을 분석한 결과, 성장온도 $200^{\circ}C$에서 제작한 박막이 가장 양호한 결정성을 나타냈다. 또한 AFM으로 관찰한 PbSe 박막의 표면형태도 $200^{\circ}C$에서 성장시킨 박막의 표면입자들이 가장 규칙적인 배열을 보였다. Hall 측정결과, PbSe 박막은 n-type 반도체임을 알 수 있었고, 전류-전압 특성 곡선은 전형적인 p-n junction 현상을 나타냈다. 또한 n-type 반도체인 PbSe 박막의 전기전도도는 일반적인 반도체의 값보다 약간 큰 것으로 확인되었다.

• 한국결정성장학회지
• /
• 제23권6호
• /
• pp.279-282
• /
• 2013

최근 관심이 높아지고 있는 GaN, SiC 단결정과 함께 자외선 LED 및 전력 반도체 용 기판 소재로서 응용성이 높은 질화갈륨(AlN, Aluminum Nitride) 단결정을 성장하였다. 아직 상용화된 AlN 기판은 없지만, 단결정 성장에 대한 연구가 이루어지고 있다. 본 연구에서는 국내 최초로 AlN 단결정의 성장 결과 직경 약 8 mm의 결정을 성장하였다. 성장된 단결정은 광학현미경으로 관찰하였으며, DCXRD를 통하여 결정성을 평가한 결과를 보고하고자 한다.

• Nuclear Engineering and Technology
• /
• 제51권7호
• /
• pp.1805-1815
• /
• 2019

While nickel-based alloys have been widely used for power plants due to corrosion resistance and good mechanical properties, during the last couple of decades, failures of nuclear components increased gradually. One of main degradation mechanisms was primary water stress corrosion cracking at dissimilar metal welds of piping and reactor head penetrations. In this context, precise estimation of welding effects became an important issue for ensuring reliability of them. The present study deals with a series of finite element analyses and crack growth rate evaluation of Alloys 690/152. Firstly, variation of residual stresses and equivalent plastic strains was simulated taking into account welding of a cylindrical block. Subsequently, extraction and pre-cracking of compact tension (CT) specimens were considered from different locations of the block. Finally, crack growth curves of the alloys and heat affected zone were developed based on analyses results combined with experimental data in references. Characteristics of crack growth behaviors were also discussed in relation to mechanical and fracture parameters.

• 한국결정성장학회지
• /
• 제26권3호
• /
• pp.89-94
• /
• 2016

본 연구에서는 HVPE(Hydride Vapor Phase Epitaxy)를 이용하여 각각 다른 V/III ratio를 가지는 multi-step의 성장 시간 변화에 따라 r-plane 사파이어 위에 성장되는 a-plane GaN 에피층의 결정성에 대하여 연구하였다. 또한 이번 연구의 결과를 선행 연구에서 single-step으로 r-plane 사파이어 위에 성장시킨 a-GaN 에피층의 결과와 비교하였다. Multi-step으로 r-plane 사파이어 위에 a-plane GaN 에피층을 성장시켰을 때, source HCl의 유량과 성장 시간이 증가함에 따라 a-plane GaN 에피층에 대한 rocking curve의 FWHM(Full Width at Half Maximum) 값이 감소하였다. 높은 source HCl의 유량을 갖는 first step과 second step의 성장 시간과 source HCl의 유량이 증가할수록 a-plane GaN 에피층 내부의 void가 감소하였다. 결과적으로 first step과 second step의 성장 시간이 가장 긴 조건에서 성장된 a-plane GaN 에피층이 가장 낮은 FWHM 값인 584 arcsec을 가지며, azimuth angle의 의존도가 가장 적은 것으로 확인되었다.