• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.482-489
• /
• 2020

본 연구의 목적은 소비자 및 현장의 니즈에 부합하면서 다이캐스팅으로 생산할 수 있는 커플링 부품을 개발하고자 하였으며, 유동 및 응고해석을 기반으로 다이캐스팅 금형 설계, 제작, 및 사출조건 최적화 도출을 실시하였고 사출된 제품의 측정 및 평가를 수행하였다. 유동해석을 통하여 캐비티 내부가 100 % 충진되기 위한 적정한 사출조건은 용탕의 온도 670 ℃, 사출속도 1.164 m/s, 충진압력 6.324~18.77 MPa로 분석되었다. 또한, 응고율이 69.47 %일 때 4개의 캐비티 모두에서 100 %에 근접하는 응고가 발생됨을 알 수 있었으며, 이를 기초로 시사출 조건설정 등에 응용하였으며 그 결과 사이클 타임은 약 6.5초로 도출되었다. 다이캐스팅으로 시사출된 제품의 표면 및 내부의 품질 검사를 수행한 결과 성형불량 및 기공 등의 결함은 전혀 발견되지 않았으며, 주요 개소의 치수를 측정한 결과 모든 항목에서 허용하는 공차 이내의 값을 보였다. 또한, 게이트로부터 약 45 mm 이격된 곳의 평균 경도값은 97.7(Hv)로 나타나는 등 전체적으로 양호한 치수 및 품질의 부품을 제작할 수 있었다.

• 자원환경지질
• /
• 제56권3호
• /
• pp.311-330
• /
• 2023

CO₂ 배출량 증가로 인한 지구온난화 심화에 대한 주요 대책으로 CO₂를 포집하여 지중에 저장하는 이산화탄소 포집·저장(Carbon capture storage, CCS) 기술이 주목받고 있다. 최근 현무암의 거대한 체적, 높은 반응성, 풍부한 양이온 함량 등의 특성이 CO₂ 포획 및 저장 기작에 유리하게 작용한다는 사실이 부각되면서, 현무암층을 대상으로 하는 CO₂ 지중저장이 다양한 분야에서 연구되고 있다. 본 연구에서는 CO₂ 지중저장 기작, 현무암의 특성과 더불어 국외 연구 사례들을 조사 및 분석하여, 현무암 CO₂ 지중저장에 대한 타당성을 검토하였다. 조사한 사례들은 수행 방법을 기준으로 실험, 모델링, 현장 실증 연구로 분류하였다. 연구 사례별 실험 조건의 경우 온도는 20 ~ 250 ℃, 압력은 0.1 ~ 30 MPa, 암석-유체 간 반응 시간은 수 시간에서 4년까지 넓은 범위에서 진행되었다. 모델링 연구에서는 현무암 CO₂ 지중저장 후보지와 유사한 모델을 구축하여 CO₂-유체 주입 전∙후 유체역학적 및 지화학적 요인들에 대한 변화를 살펴본 사례가 다수였다. 검토 결과, 현무암은 잠재 CO₂ 저장용량이 크고, CO₂ 광물화 반응이 빠르기 때문에 현무암 CO₂ 지중저장시 온도와 압력 및 지질구조와 같은 환경적인 제약이 적다. 현장 실증 사례인 CarbFix project, Wallula project가 성공적으로 수행되어 실증 수행가능성 또한 높게 평가되고 있다. 그러나 현무암 대상 CO₂ 지중저장에서 신중히 고려해야 할 점도 존재한다. 광물화 기작이 현무암의 조성, 주입 지역의 특성 등 여러 요인에 따라 결과가 상이하게 나타나고, 탄산염과 규산염 광물 등의 침전으로 인해 관정 주입성(injectivity) 저하가 발생할 수 있다. CO₂ 주입 시 저장층 내 압력 증가가 발생할 수 있으며 암석-CO₂-유체 반응 과정에서 지중환경 오염의 위험성도 존재한다. 유체에 CO₂를 용해시켜 주입하기 때문에 기존 방식과 다른 지중 모니터링 기술 또한 요구된다. 따라서, 현무암에서의 CO₂ 지중저장을 안정적이고 효율적으로 수행하기 위해서는 적합한 대상 지역을 선별하고, 해당 지역에 대한 여러 자료를 구축하여 이를 기반으로 한 다양한 실험, 모델링, 현장 실증 등의 체계적인 연구 수행이 필요하다.

• 한국수처리학회지
• /
• 제26권6호
• /
• pp.99-107
• /
• 2018

This research has developed a high temperature steam cleaning technology using a ceramic membrane with durability against temperature and pressure conditions. In steam cleaning, steam of $120^{\circ}C$ is injected into the ceramic membrane to induce pyrolysis by the endothermic reaction to remove fouling from the membrane. The water quality of raw water was adjusted to turbidity 10, 25 NTU and DOC 2.5 mg/L, and the membrane was uniformly fouled by constant pressure operation at 100, 200, and 300 kPa. Physical backwashing was performed with water and air at a pressure of 500 kPa and steam at $120^{\circ}C$ was injected for 0 to 5 minutes. As the turbidity concentration and the operating pressure increased, the flux decreased by 0.7 to 14.4%. It is confirmed that 10.7 to 53.8% recovery is possible than physical cleaning at the injection of steam for 3 minutes, so it is considered that the steam cleaning of the ceramic membrane is effective. Compared with CEB after NaOCl (300 mg/L) filtration at 25 NTU and 300 kPa of turbidity, the steam cleaning result for 3 minutes was similar to 46.7% of CEB for 3 hours. It has been confirmed that steam cleaning is suitable for a ceramic membrane having excellent heat resistance against high temperature. It was considered to have better cleaning efficiency as compared with general physical backwashing.

• 한국CDE학회논문집
• /
• 제13권2호
• /
• pp.139-152
• /
• 2008

In order to survive worldwide competition, today's industries are experiencing strong pressure to introduce higher quality products with lower cost and shorter lead-time. Therefore, the role of design in the process of product development is increasing in significance. In this research, two methods for improving the design capability are proposed: construction of design environment and design automation using 3D CAD system. The designers and design process are the core of product design using 3D CAD system. In order to maximize the design performance, construction of the design environment including selection of a suitable system, designer training for best use of the system, establishment of an efficient design process, and stabilization of the environment are required. A method is suggested to construct design environment by systematizing the contents of the projects and consulting experiences carried out for various categories of business such as electronic devices, motorcycles, electricity parts, sanitary wares, injection molds, and die casing molds. Design automation helps reduce tedious and time-consuming jobs, simplify complicated and error-prone modeling and drawing works to shorten the lead time and improve the product quality. To develop a design automation system, understanding the process and the related knowledge on design are very important before implementing the system using API provided by 3D CAD system. In this research, an eight-step procedure is proposed for the development of a design automation system. These eight steps are analysis of needs, determination of specification, verification of specification using 3D CAD system, inspection of related API functions, programming, field test, application in practice, and maintenance. A case study in which five design automation systems in the design of turbine generators using the proposed method is introduced in detail. These systems play important roles in the generation of various output items including 3D models, drafts, material information, and NC data. The case study shows how effectively the design time is reduced and the quality improved using those systems.

• 한국동물위생학회지
• /
• 제44권4호
• /
• pp.227-237
• /
• 2021

Artificial insemination of Korean native cattle (KNC) is the predominant method for breed improvement. However, industrialization of embryo production and transfer is necessary to utilize the genetic potential of KNC. The aim of this study was to examine associations between KNC donor cows and ovum pick-up (OPU) conditions, in-vivo oocyte recovery, and embryo development. Oocyte recovery and blastocyst development rates were higher at 50 and 60 mmHg OPU vacuum pressure than at 40 mmHg, which was, however, not significant. Regarding follicle growth, injection of 500 ㎍ GnRH 36 hours before OPU significantly increased the number of OPU oocytes from an average of 4.6 to 7.6 (P<0.05); no significant difference in embryo development rates was observed. Significant differences were observed in the numbers of OPU oocytes, embryo development rates, and transplantable blastocysts per individual among nine KNC donors (P<0.05). Furthermore, although there was no difference in OPU oocyte recovery intervals in approximately 2~8 weeks, the number of recovered oocytes significantly decreased at the 12-week interval (P<0.05); there was no difference in embryo development rates. The number of oocytes and embryonic development rates only tended to decrease until the seventh OPU session, but decreased significantly until the eighth session (P<0.05). The average pregnancy rate after transfer of OPU-derived in-vitro embryos into recipient cows was 41.8%. To improve the efficiency of OPU egg recovery and in-vitro embryo production, considering KNC donor characteristics, vacuum pressure of 60 mmHg, GnRH pretreatment to induce follicle growth, and effective OPU egg recovery up to seven times at intervals of 2~4 weeks appears to be most suitable. This study may facilitate the industrialization of KNC embryo production and transfer using high-quality cows.

• Bulletin of the Korean Chemical Society
• /
• 제33권2호
• /
• pp.553-558
• /
• 2012

A simple new method was developed for the determination of betaine in Fructus Lycii using hydrophilic interaction liquid chromatography with evaporative light scattering detection (HILIC-ELSD). Good chromatographic separation and reasonable betaine retention was achieved on a Kinetex HILIC column ($2.1{\times}100mm$, $2.6{\mu}m$) packed with fused-core particle. The mobile phase consisted of (A) acetonitrile and (B) 10 mM ammonium formate (pH 3.0)/acetonitrile (90/10, v/v). It was used with gradient elution at a flow rate of 0.7 mL/min. The column temperature was set at $27.5^{\circ}C$ and the injection volume was $10{\mu}L$. The ELSD drift tube temperature was $50^{\circ}C$ and the nebulizing gas (nitrogen) pressure was 3.0 bar. Stachydrine, a zwitterionic compound, was used as an internal standard. Calibration curve over $10-250{\mu}g/mL$ showed good linearity ($R^2$ > 0.9992) and betaine in the 70% methanol extract of Fructus Lycii was well separated from other peaks. Intraand inter-day precision ranged from 1.1 to 3.0% and from 2.4 to 5.3%, respectively, while intra- and inter-day accuracy ranged from 100.0 to 107.0% and from 94.3 to 103.9%, respectively. The limit of quantification (LOQ) was $10{\mu}g/mL$ and the recoveries were in the range of 98.2-102.7%. The developed HILIC-ELSD method was successfully applied to quantitatively determine the amount of betaine in fourteen Fructus Lycii samples from different locations, demonstrating that this method is simple, rapid, and suitable for the quality control of Fructus Lycii.

• 청정기술
• /
• 제26권1호
• /
• pp.13-21
• /
• 2020

지하역사 내 대기오염물질은 외부에서 유입되거나 또는 지하철 내부의 승객 승·하차 시 발생하는 등 여러 가지 요인에 의해 복합적으로 발생한다. 최근 연구 결과에 따르면, 지하역사 내 터널 및 지하철역에서 발생하는 대부분의 대기오염물질은 열차풍에 의해 발생되는 것과 같이 내부적 요인에 많은 영향을 많이 받는 것으로 알려져 있다. 이러한 대기오염물질을 제어하기 위해서는 지하철역사 내에 전기집진장치와 같은 집진시설이 필요하며, 집진장치에 의해 제거된 미세먼지를 보다 효율적으로 관리하기 위해서는 집진장치 내부에 지속적인 세척이 필수적이다. 따라서 본 연구에서는 지하역사에 설치할 전기집진장치 내부 집진판에 쌓인 미세먼지를 세척하기 위한 나노버블세척 장치를 개발하였고 나노버블수의 먼지세척효율을 평가하고자 하였다. 실험 결과, 분사압 증가에 따라 세척 효율이 일정하게 증가하였고 나노버블수로 세척할 경우 수돗물로 세척한 경우보다 부착먼지 제거효율이 130.8% 더 증가하였다. 세척횟수 증가에 따라 최대 제거효율은 수돗물에 비해 143.1% 높았지만 적합한 세척횟수는 3회 미만인 것으로 나타났다. 또한 나노버블수 체류시간 변화에 따른 세척효율 실험결과, 나노버블수의 최대 체류시간은 5분 이내로 유지됨을 확인하였다.

• 대한간호
• /
• 제29권2호
• /
• pp.48-65
• /
• 1990

The government has adopted a policy to introduce Home Health Care Program, and has established a three stage plan to implement it. The three stage plan is : First, to amend Article 54 (Nurses for Different Types of Services) of the Regulations for Implementing the Law of Medical Services; Second, to tryout the new system through pilot projects established in public hospitals and clinics; and third, to implement at all hospitals and equivalent medical institutions. In accordance with the plan, the Regulation has been amend and it was promulgated on January 9,1990, thus establishing a legal ground for implementing the policy. Subsequently, however, the Medical Association raised its objection to the policy, causing a delay in moving into the second stage of the plan. Under these circumstances, a study was conducted by collecting and evaluating the opinions of physicians, nurses, non-medical personnel and patients on the need and expected result from the home health care for the purpose of help facilitating the implementation of the new system. As a result of this study, it was revealed that: 1. Except the physicians, absolute majority of all other three groups - nurses, non-medical personnel and patients -gave positive answers to all 11 items related to the need for establishing a program for Home Health Care. Among the physicians, the opinions on the need for the new services were different depending on their field of specialty, and those who have been treating long term patients were more positive in supporting the new system. 2. The respondents in all four groups held very positive view for the effectiveness and the expected result of the program. The composite total of scores for all of 17 items, however, re-veals that the physicians were least positive for the- effectiveness of the new system. The people in all four groups held high expectation on the system on the ground that: it will help continued medical care after the discharge from hospitals; that it will alleviate physical and economic burden of patient's family; that it will offer nursing services at home for the patients who are suffering from chronic disease, for those early discharge from hospital, or those who are without family members to look after the patients at home. 3. Opinions were different between patients( who will receive services) and nurses (who will provide services) on the types of services home visiting nurses should offer. The patients wanted "education on how to take care patients at home", "making arrangement to be admitted into hospital when need arises", "IV injection", "checking blood pressure", and "administering medications." On the other hand, nurses believed that they can offer all 16 types of services except "Controlling pain of patients", 4. For the question of "what types of patients are suitable for Home Health Care Program; " the physicians, the nurses and non-medical personnel all gave high score on the cases of "patients of chronic disease", "patients of old age", "terminal cases", and the "patients who require long-term stay in hospital". 5. On the question of who should control Home Health Care Program, only physicians proposed that it should be done through hospitals, while remaining three groups recommended that it should be done through public institutions such as public health center. 6. On the question of home health care fee, the respondents in all four groups believed that the most desireable way is to charge a fixed amount of visiting fee plus treatment service fee and cost of material. 7. In the case when the Home Health Care Program is to be operated through hospitals, it is recommended that a new section be created in the out-patient department for an exclusive handling of the services, instead of assigning it to an existing section. 8. For the qualification of the nurses for-home visiting, the majority of respondents recommended that they should be "registered nurses who have had clinical experiences and who have attended training courses for home health care". 9. On the question of if the program should be implemented; 74.0% of physicians, 87.5% of non-medical personnel, and 93.0% of nurses surveyed expressed positive support. 10. Among the respondents, 74.5% of -physicians, 81.3% of non-medical personnel and 90.9% of nurses said that they would refer patients' to home health care. 11. To the question addressed to patients if they would take advantage of home health care; 82.7% said they would if the fee is applicable to the Health Insurance, and 86.9% said they would follow advises of physicians in case they were decided for early discharge from hospitals. 12. While 93.5% of nurses surveyed had heard about the Home Health Care Program, only 38.6% of physicians surveyed, 50.9% of non-medical personnel, and 35.7% of patients surveyed had heard about the program. In view of above findings, the following measures are deemed prerequisite for an effective implementation of Home Health Care Program. 1. The fee for home health care to be included in the public health insurance. 2. Clearly define the types and scope of services to be offered in the Home Health Care Program. 3. Develop special programs for training nurses who will be assigned to the Home Health Care Program. 4. Train those nurses by consigning them at hospitals and educational institutions. 5. Government conducts publicity campaign toward the public and the hospitals so that the hospitals support the program and patients take advantage of them. 6. Systematic and effective publicity and educational programs for home heath care must be developed and exercises for the people of medical professions in hospitals as well as patients and their families. 7. Establish and operate pilot projects for home health care, to evaluate and refine their programs.