• 한국정보통신설비학회:학술대회논문집
• /
• 한국정보통신설비학회 2007년도 학술대회
• /
• pp.436-439
• /
• 2007

This paper describes the optimization of PGS(Patterned Ground Shield) of 5.5 turns rectangular spiral inductor using Taguchi's method. PGS is decrease method of parasite component by silicon substrate among dielectric loss reduction method. By using the taguchi's method, each parameter is fixed upon that PGS high poison(A), slot spacing(B), strip width(C) and overlap turn number(D) of PGS design parameter. Then we verified that percentage contribution and design sensitivity analysis of each parameter and level by signal to noise ratio of larger-the-better type. We consider percentage contribution and design sensitivity of each parameter and level, and then verify that model of optimization for PGS is lower inductance decreasing ratio and higher Q-factor increasing ratio by EM simulation.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 하계종합학술대회논문집
• /
• pp.367-370
• /
• 1998

A hybrid-integrated SAW(surface acoustic wave) douplexer including transmitter(Tx) filter, receiver(Rx) filter an dantenna terminal has been studied. The prototype duplxer was designed for CDMA system application in the 800 MHz-band. Ladder type SAW filters consisting of one port SAW resonators wer integrated on epoxy substrate to demonstrate the feasiblity of antenna duplexer. In order to perform the duplexing function, a strip line for impedance transformaton with length of .gamma./4 was inserted at rx path. The fabricted duplexer has an insertion loss of 3.0 dB at Tx path and 3.7 dB at Rx path. The attenuation has more than 40dB.

• 한국항해학회지
• /
• 제3권2호
• /
• pp.1-19
• /
• 1979

The advanced researches of the ship's motion in the seaway can predict the heaving, pitching and slamming of ship's motion. The researches as of today are that of displacement type such as a small typical fishing boat and U, UV and V bow ship forms under low speed. In recent day, the study of behaviours of high speed planning boat in the regular waves has been carried out by Bessho [5]. The calculation about behaviours of a high speed vessel in the longitudinal regular waves is calculated by Ordinary Strip Method in this paper. The data of the results were discussed and compared with Bessho's results. The conclusions deduced from this study are as follow, (1) The acceleration of motion calculated by the O.S.M. is similar with Bessho's data for the Fn 0.5 (2) The amplitudes of the behaviours of motions take peak at 1.0<λ/L<1.4.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 가을 학술발표회 논문집
• /
• pp.87-94
• /
• 2000

This paper concerns the distribution of earth pressures on a cantilever wall with unattached reinforcements in the backfill. This type of walls is different from the existing reinforced earth walls in that unattached reinforcements are placed in the backfill of rigid retaining wall such as gravity wall and cantilever wall, instead of connecting reinforcements to the wall segments. Two large-scale prototype tests have been carried out with a 4m high cantilever wall; one with unreinforced backfill, the other with unattached strips in the backfill. The reinforcing effect of unattached strips are discussed based on the earth pressure distribution measured in two large-scale prototype tests. Also, the comparison between measured and predicted earth pressure on a wall with unattached strips are discussed herein to confirm the validity of analytical prediction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.342-342
• /
• 2010

This paper mainly focuses and describes four-armed dual-band rectangular type patch antenna using teflon of 0.54 mm thickness substrate for the application in personal wireless communications at about 2 GHz and 2.5 GHz frequency ranges. The dual-band patch antenna is obtained by embedding one centered and two pairs of rectangular patches on single body above the substrate. Details of the proposed antenna design are presented and discussed as a novel design with remarkable value of return loss (S11) of -28.68 dB and it is the most suitable for WiMAX applications as well.

• 한국초등과학교육학회지:초등과학교육
• /
• 제17권1호
• /
• pp.105-112
• /
• 1998

It is well known that making electric motors is very difficult in chapter 2, "Electric Current and Magnetic Field", natural science textbook 6-1 in primary school. In the present paper, we propose a new and successful method for making them. The most important point is that iron cores are not used in making electromagnets. This resolves the problem that both poles of electromagnet can be attracted by any pole of permanent magnet because of iron core in the electromagnet. The thick enamel wire is used as arms of armature so that they can support the electromagnet stably and we can reliably strip off the skin of the enamel wires, completely for one end and half for the other end of the enamel wires coming from the electromagnet. In addition, we suggest the ring-type support made of aluminum foil and the M-shaped support made of thick enamel wire that can substitute for the M-shaped copper wire support for armature. armature.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(2)
• /
• pp.181-184
• /
• 2001

A coplanar waveguide(CPW) on a dielectric substrate consists of a center strip conductor with semi-infinite ground planes on either side. This type of waveguide offers several advantages over microstrip line. It facilitates easy shunt as well as series mounting of active and passive devices. It eliminates the need for wraparound and via holes, and it has a low radiation loss. These, as well as several other advantages, make CPW ideally suited for microwave integrated circuit applications. However, very little information is available in the literature on models for CPW discontinuities. This lack of sufficient discontinuity models for CPW has limited the application of CPW in microwave circuit design. We presented for the characteristics of coplanar waveguide open end capacitance and series gap capacitance. Measurements by utilizing the resonance method were made and the experimental data confirmed the validity of theories. The relationships between the CPW capacitances and the physical dimensions were studied.

• 전자공학회논문지D
• /
• 제35D권7호
• /
• pp.109-116
• /
• 1998

In this work was produced and analyzed a z-cut Ti:LiNbO$_{3}$ optical waveguide which applies for various optical devices.A waveguide channel with a thickness 8 .mu.m and a length 66,000.mu.m and a mach-zehnder interferometer type waveguide were fabricated at a diffusion temperature 1050.deg. C for 6-8hours in a wet $O_{2}$ environment. The resulting Ti:LiNbO$_{3}$ optical waveguide was measured to have a Ti-strip thickness of 950.angs. and low loss. Surfaces and cross-sections of a fabricated waveguide were analysed. The mode pattern anaysis revealed that the waveguide showed a single mode at a 1550nm wavelength. The effective dimension of the waveguide was calculated by measuring a gaussian profile; Wx=10.95.mu. and Wy=9.14.mu.m. a propagation loss, of 0.50dB/cm for a TM mode and 0.45dB/cm for a TE mode, was low enough to be accepatable for optical devices.

• 대한조선학회논문집
• /
• 제34권2호
• /
• pp.75-84
• /
• 1997

본 연구에서는 스펙트럼 해석법에 기초한 새로운 개념의 정밀한 선체구조 피로강도평가 시스템을 개발하였으며 membrane 방식 LNG 운반선을 대상으로 하여 수치계산을 수행함으로써 그 효용성을 검증하였다. 선체에 작용하는 파랑하중을 스트립 이론으로 직접계산하고 3차원 정밀 구조해석과 영향계수 개념을 바탕으로 Miner 법칙에 의한 누적손상도를 계산하여 설계기준과 비교, 검토하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1999년도 제3회 압연심포지엄 논문집 압연기술의 미래개척 (Exploitation of Future Rolling Technologies)
• /
• pp.3-9
• /
• 1999

The recent technical trend in hot rolling of steel can be described as process and product technologies which have been progressed with modern mill equipment and computers. Precise gauge and width control can be achieved by up-to-date control methods such as AGC and AWC systems. Roll benders and various shape control systems enabled high quality flatness and crown control. Mills can produce higher tensile materials by new process based on process metallurgy. The use of high speed steel rolls and on line roll grinders make the schedule free rolling easier which results in cost saving. Process itself goes toward continuous and simple flow type which has lower operation. Endless rolling and strip casting are examples of the trend. Materials with higher tensile strength and various functions have been developed in last years to meet the customer's needs and this trend will continue.