• Journal of Technologic Dentistry
• /
• v.40 no.4
• /
• pp.209-215
• /
• 2018

Purpose: The purpose of this study was to evaluate the clinical acceptability of the marginal and internal gap of Co-Cr metal copings fabricated with stereolithography (SLA). Methods: Titanium master dies were milled after scanning of the prepared tooth (n=30). For group I, Co-Cr metal copings were made from conventional lost-wax technique(LWT, n=10). For group II, the master dies were scanned and designed with CAD system. Then, metal copings were milled with Co-Cr(SUB, n=10). For group III(ADD, n=10), the scanning and design procedures were same as group II and burn-out resins were fabricated with SLA device. The marginal and internal discrepancies were measured under an optical microscope(100x) on ten reference points and were statistically analyzed with one-way ANOVA(${\alpha}=.05$). Results: The mean total discrepancies were $53.76{\pm}12.42{\mu}m$ in the LWT group and $69.82{\pm}15.48{\mu}m$ in the ADD group. The SUB group showed the largest total mean value $110.33{\pm}13.77{\mu}m$. There was statistically significant difference between the SUB and the other groups(P<0.05). Conclusion : Co-Cr metal copings fabricated with SLA technology showed clinically acceptable value on marginal and internal gap and there was no statistically significant difference between conventional lost-wax technique and SLA.

• Journal of dental hygiene science
• /
• v.22 no.4
• /
• pp.249-255
• /
• 2022

Background: Sexual dimorphism is important for sex determination in the field of forensics. However, sexual dimorphism is commonly assessed using cone beam computed tomography (CBCT) rather than three-dimensional (3D) modeling software; therefore, studies using a more accurate measurement approach are necessary. This study assessed the sexual dimorphism of the MS using a 3D modeling program to obtain information that could contribute to the fields of surgery and forensics. Methods: The CBCT data of 60 patients (age, 20~29 y; 30 males and 30 females) admitted to the Department of Orthodontics at the Dankook University School of Dentistry were provided in Digital Imaging and Communications in Medicine (DICOM) format. The left MS and right MS were modeled based on the DICOM files using the Mimics (version 22; Materialise, Leuven, Belgium) 3D program and converted to stereolithography (STL) files used to measure the width, length, and height of the MS, infraorbital foramen (IOF), right MS, and left MS. The average of three repeated measurements was calculated, and a reliability test was performed to ensure data reliability (Cronbach's α=0.618). A canonical discriminant analysis was performed using a standard approach (left: Box's M=0.096; right: Box's M=0.115). Results: Males had greater values for all parameters (MS width, MS length, MS height, IOF, right MS, left MS) than females. The discriminant analysis identified six independent variables (MS width, MS height, MS length, IOF, right MS, left MS) that could identify sex. The left MS and right MS correctly identified the sex of 81.7% and 71.7% of the patients, respectively, with the left MS having higher accuracy. Conclusion: This study confirmed that, for Korean individuals, the left MS has a better ability to identify sex than the right MS. These results may contribute to sex identification in the fields of surgery and forensics.

• International Journal of Precision Engineering and Manufacturing
• /
• v.9 no.3
• /
• pp.51-54
• /
• 2008

A novel stereolithography method using evanescent light has been proposed as a means to realize 100-nanometer resolution. An in-process measurement system with high accuracy has been introduced to the nanostereolithography apparatus. Specifically, an optical microscopic system was developed to monitor the exposure process and a confocal positioning system was established to improve the longitudinal positioning accuracy in the layer-by-layer process. A high-power objective lens, a tube lens, and a charge coupled device (CCD) were included in the optical microscopic system, whereas a laser, a high-power objective lens, a piezoelectric (PZT) stage, a condenser lens, a pinhole, and a photomultiplier (PMT) made up the confocal microscopic system. Two verification experiments were conducted, and the results indicated that the optical microscopic system had a horizontal resolution of 200 nm and that the confocal positioning system provided a depth resolution of 30.8 nm. These results indicate that nanostereolithography can be successfully performed with this system.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1415-1418
• /
• 2008

Scaffold fabrication for regenerating functional human tissues has an important role in tissue engineering, and there has been much progress in research on scaffold fabrication. However, current methods are limited by the mechanical properties of existing biodegradable materials and the irregular structures that they produce. Recently, Solid freeform fabrication (SFF) technology was remarked by fabricating 3D free-form micro-structures. Among SFF technologies, we tried to fabricate scaffolds using micro-stereolithography which contain the highest resolution of all SFF technologies and precision deposition system which can use various biomaterials. And we developed the CAD/CAM system to automate the process of scaffold fabrication and fabricate the patient customized scaffolds. These results showed the unlimited possibilities of our SFF technologies in tissue engineering.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.8 s.197
• /
• pp.138-143
• /
• 2007

Microstereolithography technology is similar to the conventional stereolithography process and enables to fabricate a complex 3D microstructure. This is divided into scanning and projection type according to aiming at precision and fabrication speed. The scanning MSL fabricates each layer using position control of laser spot on the resin surface, whereas the projection MSL fabricates one layer with one exposure using a mask. In the projection MSL, DMD used to generate dynamic pattern consists of $1024{\times}768$ micromirrors which have $13.68{\mu}m$ per side. The fabrication range and resolution are determined by the field of view of the DMD and the magnification of the projection lens. If using the projection lens with high power, very fine microstructures can be fabricated. In this paper, the projection MSL system adapted to a large surface for array-type fabrication is presented. This system covers the meso range, which is defined as the intermediate range between micro and macro, with a resolution of a few ${\mu}m$. The fabrication of array-type microstructures has been demonstrated to verify the performance of implemented system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.595-598
• /
• 2002

Laser scanners are getting used more and more in reverse engineering and inspection. For CNC-driven laser scanners, it is important to automate the scanning operations to improve the accuracy of capture point data and to reduce scanning time in industry. However, there are few research works on laser scan planning system. In addition, it is difficult to directly analyze multi-patched freeform models. In this paper, we propose an STL (Stereolithography) mesh based laser scan planning system for complex freeform surfaces. The scan planning system consists of three steps and it is assumed that the CAD model of the part exists. Firstly, the surface model is approximated into STL meshes. From the mesh model, normal vector of each node point is estimated. Second, scan directions and regions are determined through the region growing method. Also, scan paths are generated by calculating the minimum-bounding rectangle of points that can be scanned in each scan direction. Finally, the generated scan directions and paths are validated by checking optical constraints and the collision between the laser probe and the part to be scanned.

• Journal of radiological science and technology
• /
• v.40 no.3
• /
• pp.433-441
• /
• 2017

The 3D printing selective laser sintering (SLS) and stereo lithography apparatus (SLA) method used for bone model production has good precision and resolution, but the printers are expensive and need professional knowledge for operation. The program that converts computed tomography digital imaging and communications in medicine (DICOM) file into STL (stereolithography) file is also expensive so requesting 3D printing companies takes a lot of time and cost, which is why they are not generally utilized in surgery. To produce bone models of fractured patients, the use of 3D imaging conversion program and 3D printing system should be convenient, and the cost of device and operation should be low. Besides, they should be able to produce big size bone models for application to surgery. Therefore, by using an fused deposition modeling (FDM) method 3D printer that uses thermoplastic materials such as DICOM Viewer OsiriX and plastic wires, this study developed 3D printing system for Fracture surgery Patients customized bone model production for many clinics to use for surgery of fracture patients by universalizing with no limit in printing sizes and low maintenance and production cost. It is expected to be widely applied to the overall areas of orthopedics' education, research and clinic. It is also expected to be conveniently used in not only university hospitals but also regular general hospitals.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.9 s.174
• /
• pp.194-201
• /
• 2005

Recently, as Rapid Prototyping is attracting people's attention, many peoples are actively participating in the research on STL format. The STL files are transformed to be input for RP after modeling in CAD system. When the shape, however, needs to be changed or edited, it is impossible without the original data. So, if the original data is lost, new modeling is required. Therefore, this study suggests a way to edit the shape in STL format and to make the Boolean operation possible between the original and edited shapes. In addition, the reliability was confirmed after going over the errors of the edited data.

• CDE review
• /
• v.2 no.2
• /
• pp.12-16
• /
• 1996

Rapid Prototyping(RP)이란 짧은 시간 내에 CAD 그래픽 데이터로부터 3차원 형상의 시제품을 만들어 내는 기술을 일컬으며, 1986년 3D Systems라는 회사에 의하여 상용화된 SLA(Stereolithography Apparatus)방식을 선두로 하여 지난 10년간 급속히 발전을 해왔다. 원하는 형상의 부품을 만들 때 기존의 machining은 원자재에서 재료를 깎아내면서 만드는 반면에, RP는 재료를 한 층씩 차례로 쌓아서 부품을 만드는 가산적인 공정 특징을 가지고 있다. 액체, 고체, 심지어 기체 상태의 재료까지 다양한 재료를 사용하고 있으며 또한 여러가지 적층방법으로 부품을 제작하고 있다. 성공적인 RP기술의 창출에는 RP기계제작에 직접 관계되는 기술뿐만 아니라, 재료 기술, RP제작에 적합한 CAD데이터 생성기술, 후처리 및 가공기술 등이 모두 관건이 된다. 여기서는 RP기술의 주요 파트 제작방법과 RP에 쓰이는 재료, RP의 용도 및 그 한계성 등에 대하여 생각하여 보았다. RP기술은 3차원 CAD 모델이 없으면 실현이 불가능하다. 3차원(3D)화는 제품을 설계하고 만드는 대부분의 회사가 경쟁력을 갖기 위하여 싫든 좋든 이루어야 하는 목표 중의 하나라고 할 수 있는데, RP기술 도입은 이러한 3차원화를 단축시키는 촉매제의 역할을 할 수 있다고 생각한다. RP기술이 부분적으로 정확도의 문제와 제작 가능한 재료의 종류 및 성능에 제한이 있지만, 현재로서도 여러 응용분야에 성공적으로 이용되고 있으며 향후에는 더욱 그 응용 범위를 넓혀갈 것으로 전망된다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1994.10a
• /
• pp.884-889
• /
• 1994

In this work, rapid prototyping and three dimensional finite element analysis are simltaneously applied to design metal forming processes. Rapid prototyping is a new prototyping technology which producess three dimensional part models directly from CAD data and has been extensively applied to various manufacturing processes. There are many types of rapid prototyping systems due to their building principles and materials. In this work, Stereolithography Apparatus (SLA) which is the most widely-used rapid prototyping system is introduced to manufacture the die set. To prepare STL file generally, mesh data which are in describing the die surface in finite element analysis are translated so that rapid prototyping and finite element analysis are effectively connected. The die sets are manufactured using SLA prototypes, and matal forming experiments are carried out using them. Comparing experiments results with analyses, the processes can be predicted and designed successfully.