• Journal of Hydrospace Technology
• /
• v.2 no.1
• /
• pp.18-26
• /
• 1996

It is normal practice to consider bending wave modes only, when one applies SEA (Statistical Energy Analysis) to ship structures because of complexities in SEA modeling and evaluation of coupling loss factors for inplane modes. According to the result of Tratch[1], the inplane wave modes becomes important for the analysis of a foundation structure as the distance from the source and receiver increases. In this paper, the effect of inplane wave modes on structure-borne noise propagation in ship structures is presented. It is shown that the inplane wave could increase the noise level more than 10 dB compared with the results without inplane wave modes at high frequency bands for compartments far from the source location.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.1
• /
• pp.133-141
• /
• 1994

In this paper, experiences obtained during the development of MASS(Noise Analysis of Ship-board using SEA) are described. The results are summarized as follows. (1) The modelling techniques for ship structure and cabins are suggested. (2) Structureborne and airborne noise for a real ship were measured at sea trial and predicted by NASS. The differences between the two values are acceptably small for the cabins located on higher decks, although problems related with modelling of lower decks and evaluation of radiation efficiency were found.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.04a
• /
• pp.545-550
• /
• 1997

It is well known that Statistical Energy Analysis(SEA) is one of very attractive analytical methods to solve shipboard noise problems. With reasonable successes, many applications of SEA to shipboard noise prediction have been reported. However when one wishes to obtain theoretical predictions by using SEA in practical systems, he will find difficulty in modeling of source systems, that is, foundations where to place main engine, generator, compressor, and so on. Also, he will find that it is hard to determine the amount of power flow from machinery to structures. In this paper, SEA of a simple foundation model was carried out using the estimated amount of power flow from source; the estimated mobility method. The comparison between the estimated and measured results is presented. That comparison shows a method to get structure-borne noise power from the combination of machinery and foundation. This prediction method gave a good results for a air-compressor mounted on a model foundation. The method is expected to give a reasonable power output in practical problems.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.5
• /
• pp.1-8
• /
• 2013

Wind resource data of short-term period has to be corrected a long-term period by using MCP method that Is a statistical method to predict the long-term wind resource at target site data with a reference site data. Because the field measurement for wind assessment is limited to a short period by various constraints. In this study, 2 different MCP methods such as Linear regression and Matrix method were chosen to compare the predictive accuracy between the methods. Finally long-term wind speed, wind power density and capacity factor at the target site for 20 years were estimated for the variability of wind and wind energy. As a result, for 20 years annual average wind speed, Yellow sea off shore wind farm was estimated to have 4.29% for coefficient of variation, CV, and -9.57%~9.53% for range of variation, RV. It was predicted that the annual wind speed at Yellow sea offshore wind farm varied within ${\pm}10%$.

• Steel and Composite Structures
• /
• v.45 no.1
• /
• pp.119-131
• /
• 2022

Due to the complexity of the structure and the limits of classical SEA, a combined SEA approach is employed, with angle-dependent SEA in the low- and mid-frequency ranges and advanced SEA (ASEA) considering indirect coupling in the high-frequency range. As an important component of the steel box girder, the dynamic response of an L-junction periodic ribbed plate is calculated first by the combined SEA and validated by the impact hammer test and finite element method (FEM). Results show that the indirect coupling due to the periodicity of stiffened plate is significant at high frequencies and may cause the error to reach 38.4 dB. Hence, the incident bending wave angle cannot be ignored in comparison to classical SEA. The combined SEA is then extended to investigate the vibration properties of the steel box girder. The bending wave transmission study is likewise carried out to gain further physical insight into indirect coupling. By comparison with FEM and classical SEA, this approach yields good accuracy for calculating the dynamic responses of the steel box girder made of periodic ribbed plates in a wide frequency range. Furthermore, the influences of some important parameters are discussed, and suggestions for vibration and noise control are provided.

• The Journal of the Acoustical Society of Korea
• /
• v.32 no.5
• /
• pp.402-407
• /
• 2013

In this paper, an analysis of sound propagation between two rooms with different mediums is discussed. Statistical energy analysis (SEA) is used to consider energy equilibrium among subsystems associated with the sound pressure levels in two rooms and the vibration level of the wall between rooms. Effect of the sound radiation from the structure-borne noise of the wall on sound pressure level of the receiving room is investigated. For a numerical example, sound propagation between engine room and water tank joined by a steel plate whose size is $8.4{\times}4$ m, is considered. It is found that when the critical frequency of the plate is above the frequency range of interest, the sound pressure level in the water tank is dominated by sound transmission through the plate, while sound radiation from the structure-borne noise of the plate is negligible except low frequency range below 63 Hz.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.2
• /
• pp.32-39
• /
• 1999

In this paper, the characteristics of the ray tracing method (RTM) based on the cylindrical wave are discussed for the high frequency vibration analysis of two-dimensional structures. A ray tube describing the emanating cylindrical wave is used to derive the governing equation for incident reflected, and transmitted ray tubes which satisfies the condition at the coupled boundary. The suggested ray model is applied to panel array structures, and the predicted results for 2-panel, 3-panel, and 4-panel array structures are compared to those by Statistical energy analysis (SEA) and Wave intensity analysis(WIA). More enhanced prediction was obtained compared to the SEA, and similar prediction performance was observed to the WIA. Additionally, the RTM has a novel feature that it can estimate the spatially smoothed distribution of vibration energy and vibration intensity. It is expected that the present RTM can be used as one of the useful tools for the high frequency vibration analysis of two-dimensional coupled structures.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.738-741
• /
• 2003

In general, the essential requirement for cruisers or car ferries is the reduction in noise to ensure high quality and comfort. Recently, the Ro-Ro Passengers Ferry (ROPAX) was built in Hyundai Heavy Industries. In order to minimize the noise levels, careful attention have to De paid by the special committee of experts from the initial design stage to the sea trial. Proper countermeasures, considering the characteristics of sources and receiver spaces, were applied from the noise prediction and various experiment results. Finally, this ship was successfully delivered with excellent noise properties. This paper describes the procedure of noise analysis, the countermeasures of noise control, and the measurement results of the sea trial. Onboard noise analysis had been carried out by statistical energy analysis program and outdoor noise prediction program based on ISO9614. The prediction results are in good agreements with the measurement results. The technology to minimize the noise levels for cruisers or car ferries has been established throughout the construction of this ship.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.211-214
• /
• 2004

이륙과 음속 통과시 랜덤진동형태의 음향/진동환경에 노출되는 위성체의 음향/진동시험은 시제품을 완성한 후에 슨1행되므로 않은 시행착오를 겪거나, 과다한 안전계수를 사용하여 불필요한 무게증가 등의 문제점을 가지고 있다. 이러한 문제점을 극복하기 위하여 통계적 에너지 해석법 (Statistical Energy Analysis)을 이용한 선행 해석이 필요하다. 본 연구에서는 KOMPSAT-1 (Korea Multi-Purpose Satellite-1) 위성체의 SDM (Structural Dynamic Model)에 대하여 SEA 해석을 수행하였다. 감쇠 손실 인자 (Damping Loss Ffactor)는 단판을 분리하여, 연성 손실 인자(Coupling Loss Factor)는 SDM모델 하부의 두 샌드위치 패널을 분리하여 실험적으로 산정하였다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.79-83
• /
• 2005

SEA is a useful tool to predict noise and vibration response in high frequency region but has a weak point not to be able to express modal behavior in low frequency region. For a structure with middle subsystem having relatively higher modal density than excited subsystem and receiving subsystem, we studied the possibility that the modal behavior of receiving subsystem can express by considering finite mobility of excited subsystem. For a simply three-coupled beams which is chosen for feasibility study, the response of receiving beam was investigated with varying the length & area moment of inertia of middle beam. In case that the middle beam has relatively higher modal density than exciting beam, the application to finite mobility of excited beam led to express modal behavior of receiving beam relatively well.