• Journal of Powder Materials
• /
• v.17 no.1
• /
• pp.52-58
• /
• 2010

Bulk nanostructured metallic materials are generally synthesized by bottom-up processing which starts from powders for assembling bulk materials. In this study, the bottom-up powder metallurgy and High Pressure Torsion (HPT) approaches were combined to achieve both full density and grain refinement at the same time. After the HPT process at 473K, the disk samples reached a steady state condition when the microstructure and properties no longer evolve, and equilibrium boundaries with high angle grain boundaries (HAGBs) were dominant. The well dispersed alumina particles played important role of obstacles to dislocation glide and to grain growth, and thus, reduced the grain size at elevated temperature. The small grain size with HAGBs resulted in high strength and good ductility.

• International Journal of Automotive Technology
• /
• v.6 no.5
• /
• pp.445-451
• /
• 2005

Most of the pollutants from passenger cars are emitted during the cold-transient phase of the FTP-75 test. In order to reduce the exhaust emissions during the cold-transient period, it is essential to warm up the catalyst as fast as possible after the engine starts, and the Unburned Exhaust Gas Ignition (UEGI) technology was developed through our previous studies to help close-coupled catalytic converters (CCC) reach the light-off temperature within a few seconds after cold-start. The UEGI system operates by igniting the unburned exhaust mixture by glow plugs installed upstream of the catalyst. The flame generates a high amount of heat, and if the heat is concentrated on a specific area of monolith surface, then thermal crack or failure of the monolith could occur. Therefore, it is very important to monitor the temperature distribution in the CCC during the UEGI operation, so the local temperatures in the monolith were measured using thermocouples. Experimental results showed that the temperature of CCC rises faster with the UEGI technology, and the CCC reaches the light-off temperature earlier than the baseline case. Under the conditions tested, the light-off time of the baseline case was 62 seconds, compared with 33 seconds for the UEGI case. The peak temperature is well under the thermal melting condition, and temperature distribution is not so severe as to consider thermal stress. It is noted that the UEGI technology is an effective method to warm up the catalyst with a small amount of thermal stress during the cold start period.

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.2
• /
• pp.147-155
• /
• 2002

In this paper, the regular rotational gaits of the quadruped crawling robot are studied. It is assumed that the proposed regular rotational gaits starts from one of six support patterns in a translational gaits and end up with one of six support patterns in a translational gaits. Noting that six support patterns in a regular translational gait belong to two different groups with respect to regular rotational gait, the static stability margin and the maximum rotational displacement during one rotational stride period for the two representative support patterns are investigated. It is expected that the proposed regular rotational gaits will enhance the omni-directional characteristics of the quadruped crawling robot.

• Journal of computational fluids engineering
• /
• v.13 no.4
• /
• pp.50-57
• /
• 2008

The prediction of hydrate pellet decomposition characteristics is required to design the regasification process of GTS (gas to solid) technology, which is considered as an economic alternative for LNG technology to transport natural gas produced from small and stranded gas wells. Mathematical model based on the conservation principles, the phase equilibrium relation, equation of gas state and phase change kinetics was set up and numerical solution procedure employing volume averaged fixed grid formulation and extended enthalpy method are implemented. Initially, porous methane hydrate pellet is at uniform temperature and pressure within hydrate stable region. The pressure starts to decrease with a fixed rate down to the final pressure and is kept constant afterwards while the bounding surface of pellet is heated by convection. The predicted convective heat and mass transfer accompanied by the decomposed gas flow through hydrate/ice solid matrix is reported focused on the comparison of spherical and cylindrical pellets having the same effective radius.

• Journal of Korean Institute of Industrial Engineers
• /
• v.20 no.4
• /
• pp.181-192
• /
• 1994

In an order-oriented production system such as mold manufacturing, the production starts with an order acceptance, and the production planning is set up according to the accepted order information. Such a work can be done through a dynamic process management system which can reflect shop floor situation dynamically. In this paper, so called the Quick order acceptance evaluation system that can investigate order confirmation quickly, is discussed. When an order is asked, this system must consider the time constraint to determine whether to accept or not, and must be reliable when the determined results are used in the shop floor. For this system, firstly, we simplified the machines by grouping based on their operation capabilities, secondly, we conducted load analysis to calculate available capacities during given periods using heuristic method instead of mathematical algorithm, thirdly, expert can input his experienced knowledge into the system interactively when simulation results don't meet the required due dates. As a case study, we applied this system to an injection mold manufacturing factory.

• Journal of The Korean Astronomical Society
• /
• v.43 no.4
• /
• pp.135-139
• /
• 2010

We present the result of our investigation on the impact of the low Solar abundance of Asplund and collaborators (2004) on the derived ages for the oldest star clusters based on isochrone fittings. We have constructed new stellar models and corresponding isochrones using this new solar mixture with a proper Solar calibration. We have found that the use of the Asplund et al. (2004) metallicity causes the typical ages for old globular clusters in the Milky Way to be increased roughly by 10%. Although this may appear small, it has a significant impact on the interpretation for the formation epoch of Milky Way globular clusters. The Asplund et al. (2004) abundance may not necessarily threaten the current concordance cosmology but would suggest that Milky Way globular clusters formed before the reionization epoch and before the main galaxy body starts to build up. This is in contrast to the current understanding on the galaxy formation.

• Journal for History of Mathematics
• /
• v.26 no.2_3
• /
• pp.177-195
• /
• 2013

This study is the analysis of the concepts and the characteristics of the mathematics section of the College Scholastic Ability Test. The study starts with division of the history of the College Scholastic Ability Test into four periods. These are Introduction Period(school year 1994-1996), Adjustment Period(school year 1997-2004), Development Period(school year 2005-2011) and Conversion Period(up to present since school year 2012). The periodical division of the Mathematics section is considered as identical with that of the College Scholastic Ability Test. So we investigate the characteristics of the Mathematics section through the periodical classification. This study also proposes some tasks for the future Mathematics section of the College Scholastic Ability Test.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.1358-1365
• /
• 2010

A case study deals with Squeezing behavior under tunneling. Squeezing stands for large time-dependent convergence during tunnel excavation. Squeezing can occur in both rock and soil as long as the particular combination of induced stresses and material properties pushes some zone around the tunnel beyond the limiting shear stress at which creep starts. Under squeezing rock conditions, If the support installation is delayed the rock mass moves into the tunnel and a stress redistribution takes place around it. On the contrary, if deformation is restrained, squeezing will lead to long-term load build-up of rock support. This paper shows analysis case mutually with monitoring and numerical analysis result of squeezing behavior of Pinglin tunnel in Taiwan.

• Korean Institute of Interior Design Journal
• /
• no.25
• /
• pp.61-67
• /
• 2000

The goals and meanings of this papers are set up to analyse the trend of Design immerged in 21st century with studying Fusion culture which is related with Digital concept that is the most spot-lighted in 21st century and summarizing the effects of this tendency given to Design. We are experiencing Digital Revolution which leads us from Analog Society to Digital society. Also, this means that New Millenium starts with characteristics of [End of Century]. I focus on the concept of Fusion-design, in the view of Art-Nouveau and Post-Modernism which came over the end of 19th century and the beginning of 20th century. Furthermore, I define the Fusion-design of Digital era and find the way that design of 21st century develops.

• Korean Institute of Interior Design Journal
• /
• v.13 no.3
• /
• pp.69-75
• /
• 2004

Since 1990s, several rising western architects have been moving their theoretical background from the modern paradigm to new science and philosophy. Architectural spaces are based on the philosophy and science of their own age and the architectural theories made by them. And specially, it seems that topological spaces are different to theoretical backgrounds from idealized spaces of modern architecture. From these backgrounds, this study was performed to search for the spacial relationship and characteristics shown in the recently folding architecture and the results of this study that starts this purpose are as follows. First, the architecture that introduced by the theory of topology has appeared as the circulation forms like as Mobius band or Klein bottle, and was made the space fused with structure pursuing liquid properties of matter. As follows, second, the concept of topological space made the division of traditional concept of floor, wall, ceiling disappeared and had built up the space by continual transformation. Third, about the relationship between two spaces in topological space, the two spaces were happened by transformation of these and they have always continuity and the same quality.