• Journal of Korean Society on Water Environment
• /
• v.28 no.3
• /
• pp.426-435
• /
• 2012

The variation of stream flow is the one of the most important factors which influence on that of water quality in the unit watershed. The target water quality goal is established and permissible load is allotted in the base of the standard flow condition along with its water quality for the management of Total Maximum Daily Loads (TMDLs). A standard flow selected could cause problems in the load allotment if it was not properly arranged. This study reviewed the acquisition of water quality data, the self-variation and the retainability in water quality on the specific flow conditions. This study also proposed the median and the adjusted average flow condition out of general flow conditions as alternative standard flow conditions. It is considered that the alternatives can make the water quality data easily acquired and the water quality representativeness more enhanced on the standard flow conditions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.4
• /
• pp.233-240
• /
• 2022

The smart weapon system is a new weapon system of the future battlefield environment as a miniature guided weapon that performs precision strike missions through terminal phase guidance. However, it has small coverage to guide due to its low maneuverability because the smart weapon is controlled by using actuator of piezoelectric drive type due to the structural limitations. In this paper, we propose a firing data calculation algorithm under non-standard conditions to increase the effectiveness of the smart weapon. The proposed algorithm calculates firing data under non-standard conditions by calibrating firing data under standard conditions using information acquired in battlefield environments. The performance of the proposed algorithm is verified by numerical simulations under various conditions.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.05a
• /
• pp.235-238
• /
• 2009

This research surveys actual conditions on lighting environments of the elderly's houses. from the results of survey on actual conditions of lighting in the elderly's houses, they don't meet standard of illumination suggested by KS A 3011, and, standard of ovarall illumination is satisfied in general, but illumination in a side of work or other activities is lower than the standard and it has failed to suggest standard that is considering user's characteristics, visual characteristics going with their ages and so forth, it is thought to urgently prepare standard which considers visual characteristics of the elderly and their ages.

• Management & Information Systems Review
• /
• v.14
• /
• pp.117-132
• /
• 2004

The purpose of this study is to propose empirically the improvement measures of labor conditions of the contingent worker. Since early 1980s, the labour market in Korea has given rise to a rapid growth in contingent worker. Last year, the number has shot over 7 million mark, with the ratio standing above the 50%. This study analyses the improvement measures of labor conditions of the contingent worker. This study present five major improvement measures of labor conditions of the contingent worker. First, It's establish of the relations between organizational flexibility of the labour market and the contingent worker. Second, It's needs to realize wages level of the contingent worker. Third, the contingent worker convert standard workforce step by step. Fourth, it's make no discrimination of the between contingent worker and standard workforce. Fifthly, the government place restrictions of the contingent worker rates.

• International Journal of High-Rise Buildings
• /
• v.11 no.4
• /
• pp.331-346
• /
• 2022

Reproducing the horizontally homogeneous atmospheric boundary layer in computational wind engineering is essential for predicting the wind loads on structures. One of the important issues is to use fully developed inflow conditions, which will lead to the consistence problem between inflow condition and internal roughness. Thus, by analyzing the previous results of computational fluid dynamic modeling turbulent horizontally homogeneous atmospheric boundary layer, we modify the past hypotheses, detailly derive a new type of inflow condition for standard k-ε turbulence model. A group of remedial approaches including formulation for wall shear stress and fixing the values of turbulent kinetic energy and turbulent dissipation rate in first wall adjacent layer cells, are also derived to realize the consistence of inflow condition and internal roughness. By combing the approaches with four different sets of inflow conditions, the well-maintained atmospheric boundary layer flow verifies the feasibility and capability of the proposed inflow conditions and remedial approaches.

• Journal of radiological science and technology
• /
• v.41 no.6
• /
• pp.603-610
• /
• 2018

This study examined the following: accuracy of the exposure conditions in the inverter device and three-phase device; output waveform over the exposure conditions; and average and standard deviation of the output waveform. After assessing whether the dose corresponding to the theoretical dose was presented, the following conclusions were obtained: 1. The accuracy of the tube voltage(kVp) and tube current(mA) exposure time(sec) was within the tolerable level prescribed in Korea's Safety Management Standards. In the error, Inverter device was large the tube voltage and exposure time, the three-phase device was large the tube current. 2. In terms of the output waveform of the exposure conditions and the average and standard deviation of the output waveform, the higher tube voltage and larger tube current resulted in greater standard deviation in pulsation. Moreover, the standard deviation of pulsation was shown to be greater in the inverter device than the three-phase device; there was also greater standard deviation in the inverter device considering the exposure time. 3. Regarding the exposure conditions over the output dose, all linearity showed the coefficient of variation which had an allowable limit of error within 0.05. Although the output dose ratio for the inverter device was 1.00~1.10 times no difference that of the three-phase device, there was almost no difference in dose ratio between the tube currents.

• Korean Journal of Social Welfare Studies
• /
• v.40 no.3
• /
• pp.243-265
• /
• 2009

Using the children supplements of Korea Welfare Panel Study(first wave), this study examined that the correlation and differences between income-poverty(minimum cost of living)and housing- poverty(sub-standard housing) and analyzed the effects of living in sub-standard housing conditions on children's school achievement. The findings of the study are as follows. First, there is low correlation between income-poverty and housing-poverty. Second. there is differences of household characteristics between only housing-poverty household and only income-poverty household or income and housing poverty household. Third, living in sub-standard housing conditions has statistically significant negative effect on school achievement even after controlling for income-poverty, sex, self-esteem, adaptation to school life, family type, mother's education, private education cost, rearing behavior. The findings of this study suggest that more active housing policy approach is needed to support development of children living in sub-standard housing conditions. Based on this research, we present needed policies in the conclusion.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.845-850
• /
• 2003

Noise caused by water installations may lead to annoyance in adjacent rooms, for example in dwellings. hospitals and hotels. This part of standard describes a method of measurement allowing comparable results to be obtained in laboratory measurements. The test conditions described herein constitute the standard reference conditions essential for comparisons between laboratories.

• Journal of the Korea Institute of Building Construction
• /
• v.8 no.1
• /
• pp.37-42
• /
• 2008

As use of construction equipment has been increasing continuingly, the proportion of equipment expense to the total construction cost has become higher. However, there is a difference between the equipment expenses section in 'Poom-Sam' and practical data, because 'Poom-sam' does not consider non-working days due to weather conditions, legal holidays and management conditions. Therefore, 'Poom-Sam' does not present a reasonable standard for estimating construction equipment expenses. In this study, to estimate realistic construction equipment operating hours, firstly, construction equipment was classified according to work, and weather conditions, in which each work could not be executed, were established. Then, weather data on Seoul and Busan($2004{\sim}2006$) and legal holidays were analyzed to suggest annual standard operating hours. The annual standard operating hours of earthmoving & excavating, compaction, and drilling equipment was estimated to be 1,430 hours, and lifting equipment, concrete paving equipment, asphalt paving equipment, concrete equipment, and crushing & conveying equipment were estimated to be 2,124 hours, 1,156hours, 1,188hours, 1,688hours, and 2,152hours respectively.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.3
• /
• pp.302-308
• /
• 2021

Developers generally use test standards suggested by military standards such as MIL-STD-810G when performing vibration tests in the materiel development. However, according to MIL-STD-810G, it is recommended to test by tailoring the test standard suitable for the developed materiel, and it is specified to apply the suggested test standard only when there is difficulty in tailoring. In addition, the test standards presented by MIL-STD-810G are standards created under operating conditions different from the actual operating environment of each developed materiel, so the test according to this standard may be excessive or understated. Therefore, the developer must create an appropriate vibration test standard for the developed materiel as similar to the operating conditions as possible. In this paper, the procedure for creating the functional test standard and durability test standard suitable for the operating environment of the equipment to be mounted on the propeller aircraft under development is described, and the created standard is introduced.