• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.6
• /
• pp.727-736
• /
• 2021

Road tunnel lengths are increasing. Some 1,300 tunnels with 1,102 km in length had been increased till 2019 from 2010. There are 64 tunnels over 3,000 m in length, with their total length adding up to 276.7 km. Safety facilities in the event of a tunnel fire are critical so as to prevent large-scale casualties. Standards for installing disaster prevention facilities are being proposed based on the guidelines of the Ministry of Land, Infrastructure and Transport, but they may be limited to deep underground tunnels. This study was undertaken to provide guidelines for the spacing of evacuation connection passages and the widths of evacuation connection doors. Evacuation with various spacing and widths was simulated in regards to evacuation time, which is the measure of safety, using the evacuation analysis simulation software EXODUS Ver.6.3 and the fire/smoke analysis software SMARTFIRE Ver.4.1. Evacuation connection gates with widths of 0.9 m and 1.2 m, and spacings of 150 m to 250 m, were set to every 20 m. In addition, longitudinal slopes of 6 % and 0 % were considered. It was determined to be safe when the evacuation completion time was shorter than the delay diffusion time. According to the simulation results, all occupants could complete evacuation before smoke spread regardless of the width of the evacuation connection door when the longitudinal slope was 6 % and the interval of evacuation connection passage was 150 m. When the evacuation connection passage spacing was 200 m and the evacuation connection gate width was 1.2 m, all occupants could evacuate when the longitudinal slope was 0 %. Due to difference in evacuation speed according to the longitudinal slope, the evacuation time with a 6 % slope was 114 seconds shorter (with the 190 m connection passage) than with a 0 % slope. A shorter spacing of evacuation connection passages may reduce the evacuation time, but this is difficult to implement in practice because of economic and structural limitations. If the width of the evacuation junction is 1.2 m, occupants could evacuate faster than with a 0.9 m width. When the width of a connection door is 1.2 m with appropriate connection passage spacing, it might provide a means to increase economic efficiency and resolve structural limitations while securing evacuation safety.

• Knowledge Management Research
• /
• v.22 no.4
• /
• pp.103-118
• /
• 2021

Gross Domestic Product(GDP) is affected by the economic power of each industry. Therefore, using statistical data related to the food and drug industry, we tried to determine the proportion of GDP and analyzed the impact of the food, medical & drug industry on the domestic economy through comparison with other industries. The food, medical & drug industry has a wide range of industries among domestic industries and is closely related to the lives of the people. In addition, human lifespan is increasing, and recently, due to the spread of an infectious disease called COVID-19, the bio sector belonging to the food, medical & drug industry is in the spotlight. Attention is needed to the industry as the competitiveness of the food, medical & drug industry is expected to increase. The Ministry of Food and Drug Safety provides statistics on the food, medical & drug industry, but does not provide a systematic share of GDP. Since it is difficult to determine how influential the industry is compared to other industries, this study attempts to obtain the share of GDP in the food, medical & drug industry and compare it with other industries. In the process of obtaining GDP in the food, medical & drug industry sector, there was a difficulty in that the figures in statistical data were not unified by time point. In order to overcome the limitations, statistical data as a standard are determined. The GDP of the Food, Medical & Drug Industry was estimated using total added value, production, sales, and added value by industry. Compared to other industries, the Food, Medical & Drug Industry's GDP ranked second after the GDP of the manufacturing industry. As a result, it suggests that the food, medical & drug industry has a great influence on the national economic power among domestic industries.

• Food Science and Industry
• /
• v.55 no.2
• /
• pp.188-202
• /
• 2022

In the insect industry, as the scope of application of insects is expanded from pet insects and natural enemies to feed, edible and medicinal insects, the demand for quality control of insect raw materials is increasing, and interest in securing the safety of insect products is increasing. In the process of expanding the industrial scale, controlling the temperature and humidity and air quality in the insect breeding room and preventing the spread of pathogens and other pollutants are important success factors. It requires a controlled environment under the operating system. European commercial insect breeding facilities have attracted considerable investor interest, and insect companies are building large-scale production facilities, which became possible after the EU approved the use of insect protein as feedstock for fish farming in July 2017. Other fields, such as food and medicine, have also accelerated the application of cutting-edge technology. In the future, the global insect industry will purchase eggs or small larvae from suppliers and a system that focuses on the larval fattening, i.e., production raw material, until the insects mature, and a system that handles the entire production process from egg laying, harvesting, and initial pre-treatment of larvae., increasingly subdivided into large-scale production systems that cover all stages of insect larvae production and further processing steps such as milling, fat removal and protein or fat fractionation. In Korea, research and development of insect smart factory farms using artificial intelligence and ICT is accelerating, so insects can be used as carbon-free materials in secondary industries such as natural plastics or natural molding materials as well as existing feed and food. A Korean-style customized breeding system for shortening the breeding period or enhancing functionality is expected to be developed soon.

• Journal of the Daesoon Academy of Sciences
• /
• v.39
• /
• pp.69-97
• /
• 2021

'Déconstruction' is a system of thought that induces the emergent property that characterizes contemporary philosophy. The tradition of ancient Greek philosophy evolved over and over again, giving rise to the Renaissance and Enlightenment. It seemed to have reached its end under the historical perspective of modernity. However, contemporary philosophy wanted to see more possibilities through the deconstruction of modern philosophy. If modern philosophy dreams of a strange cohabitation between God and man with the humanistic completion of Plato's philosophy, modern philosophy rejects even that through deconstruction. Although Plato's classical metaphysics is a stable system centered around the absolute, it is ultimately based on God and religion. Under that system, human autonomy is only the autonomy bestowed by God. Contemporary philosophy is one of the results of efforts that try to begin philosophy from the original human voice through deconstruction. Instead of epistemology dependent on metaphysics, they wanted to establish epistemology from human existence and realize the best good that would set humans free through deconstruction. As such, it is no mistake to say that deconstruction is also an extension of the modern topic of human freedom. Deconstruction and human freedom act as one body in that the two cannot be separated from each other. Oddly enough, Daesoon Thought, which seems to have religious faith and traditional conservatism as main characteristics, has an emergent property that encompasses modern and contemporary times. The period of Korea, when Kang Jeungsan was active and founded Daesoon Thought, has an important meaning for those who have a keen view of history. Such individuals likely think that they have found a valuable treasure. This is because that period was a time when ideological activities were conducted due to an intense desire to discover the meaning of human freedom and envision a new world without copying the ways of the West. Instead they looked to face internal problems and raise people's awareness through subjectivity. In other words, the subtle ideas created by Korea's self-sustaining liberalism often take the form of what is commonly called new religions in modern times. Among these new religions, Daesoon Thought, as a Chamdonghak (true Eastern Learning), aims to spread a particular modern value beyond modern times through the concept of Haewon (the resolution of grievances) that was proclaimed by Jeungsan. The Haewon espoused in Daesoon Thought is in line with the disbandment of modern philosophy in that it contains modernity beyond modern times. First, Haewon means to resolve the fundamental resentment of human existence, which arose from Danju's grievance. Secondly, Haewon in Daesoon Thought encompasses the Haewon of the Three Realms of Heaven, Earth, and Humanity centers on a Haewon-esque style of existence called Injon (Human Nobility). Haewon in Daesoon Thought can be understood in the same context as Derrida's philosophy of Deconstruction. Modern deconstruction attempts to expose the invisible structures and bonds within human society and attempt to destroy them. In a similar way, Haewon endeavors to resolve the conflicts among the Three Realms by releasing the bonds of fundamental oppression that hinder the Three Realms of Heaven, Earth, and Humanity.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.50 no.2
• /
• pp.41-63
• /
• 2022

The purpose of this study is to secure objective and precise data through ecosystem monitoring, to reveal ecological characteristics through comparison and analysis with past survey data, and to accumulate basic data for diagnosing the current situation and predicting changes in the ecosystem. The target site is the 'Quercus mongolica forest on the Buksa-myeon of Namsan', which was designated as an Ecological Landscape Conservation Area (ELCA) of Seoul in July 2006. The research contents are analysis of soil environment change (1986~2016), change of actual vegetation (1978~2016), and change of plant community structure (1994~2016). A total of 8 fixed surveys (400~1,200m²) were established in 1994 and 2000. Analysis items are importance value, species and population, and Shannon's species diversity. The soil environment of Namsan is acidic (pH 4.40 in 2016), which is expected to have a negative impact on tree growth and vegetation structure due to its low capacity for exchangeable cations. Quercus mongolica forest in Namsan is mainly distributed on the northern slopes. The actual vegetation area changed from 49.4% in 1978 → 80.7% in 1986 → 82.4% in 2000 → 88.3% in 2005 → 88.3% in 2009 → 70.3% in 2016. In 2016, the forest decreased by 18% compared to 2009. While there was increased growth of Quercus mongolica in the tree layer from 2009 to 2016, the overall decline in vegetation area was due to logging and fumigation management following the spread of oak wilt in 2012. As for the changes in the plant community structure, Quercus mongolica of the tree layer was damaged by oak wilt, and the potential vegetation that can form the next generation was ambiguous. In the subtree layer, the force of urbanization tree species such as Styrax japonicus, Sorbus alnifolia, and Acer palmatum. was maintained or increased. In the shrub layer, the number of trees and species increased significantly due to the open tree crown, and accordingly, the species diversity of Shannon for woody plants also increased. In Quercus mongolica forest of Namsan, various ecological changes are occurring due to the effects of urban environments such as air pollution and acid rain, the limitation of Quercus mongolica pure forest due to oak wilt, and the introduction of exotic species, thus, it is necessary to establish a management plan through continuous monitoring.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.47 no.4
• /
• pp.361-368
• /
• 2021

The objective of this study was to establish technology for removing bacteria with human- and eco-friendly material. Staphylococcus aureus as an important component for balanced equilibrium among microbiomes, was cultured under various concentrations of phosphate. Experimental observation relating to physical properties was performed in an addition of phosphate buffer. Statistically minimum value of size and hardness using atomic force microscope was observed on the matured biofilm at 5 mM concentration of phosphate. As a result of absorbance for the biofilm tagged with dye, concentration of biofilm was reduced with phophate, too. To identify whether this reduction by phosphate at the 5 mM is caused by counter ion or not, sodium chloride was treated to the biofilm under the same condition. To elucidate components of the biofilm counting analysis of the biofilm using time-of-flight secondary ion mass spectrometry was employed. The secondary ions from the biofilm revealed that alteration of physical properties is consistent to the change of extracellular polymeric substrate (EPS) for the biofilm. Viscoelastic characterization of the biofilm using a controlled shear stress rheometer, where internal change of physical properties could be detected, exhibited a static viscosity and a reduction of elastic modulus at the 5 mM concentration of phosphate. Accordingly, bacteria at the 5 mM concentration of phosphate are attributed to removing the EPS through a reduction of elastic modulus for bacteria. We suggest that the reduction of concentration of biofilm induces dispersion which assists to easily spread its dormitory. In conclusion, it is elucidated that an addition of phosphate causes removal of EPS, and that causes a function of antibiotic.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.2
• /
• pp.168-184
• /
• 2022

This paper examined the construction techniques of the earthen fortifications in the Hanseong Period of Baekje Kingdom, which has been researched most frequently among the Three Kingdoms. The construction processes of the Earthen Fortifications were reviewed and dividing into 'selection of location and construction of the base', 'construction of the wall', and 'finish, extension and repair'. The results show that various techniques were mobilized for building these earthen fortifications. Techniques which were adequate for the topography were utilized for reinforcing the base, and several other techniques were used for constructing the wall. In particular, techniques for wall construction may be clearly divided into those of the fill(盛土) and panchuk(版築) techniques. The fill method has been assumed since the 2000s to have been more efficient than the panchuk technique. This method never uses the structure of the panchuk technique and is characterized by a complex soil layer line, an alternate fill, use of 'earth mound(土堤)'/'clay clod(土塊)', and junctions of oval fill units. The fill method allows us to understand active technological sharing and application among the embankment structures in the period of the Three Kingdoms. The panchuk technique is used to construct a wall using a stamped earthen structure. This technique is divided into types B1 and B2 according to the height, scale, and extension method of the structure. Type B1 precedes B2, which was introduced in the late Hanseong Period. Staring with the Pungnap Earthen Fortification in Seoul, the panchuk technique seems to have spread throughout South Korea. The techniques of the fill and panchuk techniques coexisted at the time when they appeared, but panchuk earthen fortifications gradually dominated. Both techniques have completely different methods for the soil layers, and they have opposite orders of construction. Accordingly, it is assumed that both have different technical systems. The construction techniques of the earthen fortifications began from the Hanseong Period of Baekje Kingdom and were handed down and developed until the Woongjin-Sabi Periods. In the process, it seems that there existed active interactions with other nations. Recently, since studies of the earthen fortifications have been increasing mainly in the southern areas, it is expected that comparative analysis with neighboring countries will be done intensively.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.2
• /
• pp.66-79
• /
• 2022

In the mid-Kofun period, the technology employed in the southern part of the Korean Peninsula had reached the Japanese archipelago, and a Japanese-style unglazed earthenware called Sueki was produced. During the early period of the spread of technology, regional elements from all over the Korean Peninsula remained strong, with production on the Japanese archipelago carried out only in very limited regions. After that, production in all parts of the archipelago began gradually. The Sueki culture was introduced to the Japanese archipelago with the technology of the Korean Peninsula; however, many excavations have been reported in the Korean Peninsula(these excavations are even called Suekitype). Many of these excavations were conducted in Jeolla-do, Yeongnam, and the Yeongsan River basin. As revealed in previous studies, however, many imitations were excavated around Jeolla-do, while Sueki of the Japanese archipelago were excavated from tombs in the Yeongnam area. The excavation period was generally from the late 5^th century to the early 6^th century(especially from the TK23 to MT15 stage), which is fundamentally different from that of Jeolla-do. Regarding the locations where Sueki were excavated, the majority were found in the tombs of local authorities. They were rarely excavated from the tombs of the royal people. Furthermore, there is no evidence of special meaning given to funeral ceremonies or Sueki in the Japanese archipelago form; therefore, most of them are thought to have been treated the same as unglazed earthenware. Considering the tombs as a whole, influential people(groups, families, and forces) were not only connected to certain areas of the Gaya region but also had complex and larger relationships. In other words, the Sueki excavated from the Yeongnam area may reflect the rise and fall of the forces in each Gaya region and the changes of the Yeongnam period. The role of negotiation and exchange can be seen not only from the fact that influential people in the central government of the Gaya region were involved but also from the existence of areas(groups, families, forces) discovered in the Gaya region indicating mutual relationships.

• Korean Journal of Plant Resources
• /
• v.35 no.2
• /
• pp.201-241
• /
• 2022

This study was investigated distributed the vascular flora of around Haemyeong Mt., located in Seokmodo, Incheon, and compared invasive alien plants in the surrounding forest 14 areas. This study carried out to be established a monitoring system for the remarkable plants etc. and used as basic data for biodiversity enhancement and conservation. The survey was conducted 19 times from April 2019 to October 2020. A total of 107 families, 382 genera, 616 species, 15 sub-species, 55 varieties, 8 formas, and 694 taxa were classified in the flora around Haemyeong Mt. areas. 17 taxa for Korea endemic plants. 12 taxa were classified for rare plants, and a total of 79 taxa were identified for floristic target species I~V. Halophytes consisted of 37 taxa. The invasive alien plants were classified as 66 taxa, and also there has been 126 taxa of them in Seokmodo and surrounding 14 forests. Plants that appeared in all 14 areas out of 126 taxa were classified as 7 taxa, such as Erigeron annuus. However, 48 taxa appeared only once in some areas, but it seems inevitable that they will spread in the future. Therefore, it is necessary to prepare a long-term conservation plan for native plants.

• Korean Journal of Heritage: History & Science
• /
• v.55 no.1
• /
• pp.51-61
• /
• 2022

Earthenware horn cups with horse head decorations were excavated from Tomb No. 7 of Bokcheon-dong, Dongraegu, Busan Metropolitan City. Made of earth in the shape of a horn, these cups are considered to have been used to drink alcohol or beverage. Large numbers of earthenware horn cups of various shapes were excavated from tombs located in the old territories of Silla and Gaya. A pair of earthenware horn cups were excavated from Tomb No. 7, and the two cups are almost identical in overall shapes and manufacturing techniques despite different sizes. Conservation treatment was carried out for the bigger one of the two horn cups this time. There are two cracks toward the horse head decorations around the mouth with missing parts observed. The chest of the horse touches the ground with one side decorating the horse head and the other side facing the conical mouth of the horn cup. It is in the U shape, striking a balance based on two legs attached behind. The surface of the horn cup was made with a potter's wheel, and the connection to the horse head has traces of cutting and trimming. The horse head is expressed realistically with its features including the ears, eyes, nose, and mouth well apprehended and its color is grey This study intended to investigate manufacturing techniques of the artifact by examining its internal structure through the condition survey in a non-destructive way. CT imaging was used to figure out its manufacturing techniques and to diagnose its condition, and accordingly the scientific conservation treatment was conducted to stabilize the artifact. The precise diagnosis on conservation condition found that there are two chips in the spout with their cracks extended. One of the chips is connected with separation added to the crack. The material which has been used for connection in the past was collected for the infrared spectroscopic analysis, which was identified to be nitrocellulose resin for the connection. Therefore, this conservation treatment focused on removing the old material and preventing the spread of cracks. Before conservation treatment, the condition survey and scientific examination for the artifact were carried out to secure data about the earthenware horn cup with horse head decorations(Treasure). Based on them, effective plans for its conservation treatment was sought for and then existing adhesive was safely removed, and restoration material was selected to take into account its reversibility. In addition, the conservation treatment according to optimal methodologies was conducted through the consultation meeting with experts.