• 한국정밀공학회지
• /
• 제25권11호
• /
• pp.73-82
• /
• 2008

A dynamic model of reducer for generating facility of electric pourer having bevel gear pair and planetary gear train is developed by lumped method. The model accounts for the shaft and bearing flexibilities, gyroscopic effects and the force couplings among the transverse and torsion motions due to gearing. Vibration/noise analysis as well as strength of bevel gear pair and planetary gear train are considered. Exciting forces of high reducer for generating facility of electric power areconsidered as the mass unbalance of the rotors, misalignment and a function of gear transmission error. A Campbell diagram, in which the excitation sources caused by the mass unbalance of the rotors, misalignment and the transmitted errors of the gearing are considered, shows that, at the operating speed, there are not critical speed.

• 한국안전학회지
• /
• 제10권2호
• /
• pp.77-83
• /
• 1995

An electrostatic reducer of a multi-pole high DC voltage applied type and a high frequency square wave voltage applied type have been studied to eliminate effectively and safely electrostatic charge on a dummy charged material. As a fundamental experiments, measurement were made on the decay time as a function of distance between electrostatic reducer and charged body, skewed angle of electrostatic reducer installed and wind speed of generated ions(＋ or －) by electrostatic reducer with high DC voltage and high frequency square wave voltage. Based oil the results above, a appropriate installation and method were produced as a trial for factory.

• 동력기계공학회지
• /
• 제15권4호
• /
• pp.48-53
• /
• 2011

Upon reviewing recent trends for robots, it can be seen that robots are gradually being miniaturized. However, most commercially available speed reducers have limitations in terms of structure and vibration when applied to small robots. In this respect, a tooth profile manufactured using thin plates was designed using balls and data analyzed related to numerical and FEM analysis. The speed reducer was manufactured to check their performance. The manufactured thin plate type speed reducer imposes less compressive stress on its tooth profile and balls, which can greatly increase feasibility.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.479-483
• /
• 1987

The reducers are widely used to reduce output speed and to amplify driving torque of actuator for industrial robots and many industrial units. But the vibration of robot, which is affected by the reducer, becomes a problem for robot which has to move a driven part with high accuracy. This paper compares experimentally the vibration characteristics of the reducer for industrial robot.

• 한국지능시스템학회논문지
• /
• 제16권3호
• /
• pp.315-320
• /
• 2006

산업 현장에서는 많은 종류의 감속기들이 사용되고 있다. 그 중 로봇에서는 사이클로이드(cycloid) 치형 혹은 인벌루트(involute) 치형을 가진 고정밀도의 감속기를 사용한다. 그 이유는 로봇 시스템에서는 위치 제어를 하는데 있어서 고정밀의 감속기를 사용하는 것이 필수적이기 때문이다. 본 논문에서는 기본적으로는 삼각형 치형을 가지고 있지만 새로운 직선치형을 갖는 로봇 감속기(RSR)를 제안한다. 제안한 감속기는 유한요소 해석법을 이용한 강도, 응력, 강성 테스트에서 좋은 결과를 얻을 수 있었으며, 편심계수를 변화시켜 최적의 치형 운동을 얻을 수 있도록 설계하여 응력이 적게 걸리고 소음을 낮출 수 있도록 하였다.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.181-186
• /
• 2006

In this paper, a noncontact type torque meter using silicone rubber to measure the exact torque value and reduce a vibration and a noise, was developed. When planetary gear speed reducer runs, torque, RPM etc.. of motor change according to load or speed change. So, it needs a device to detect load's change or to diagnose the state of thewhole drive department by monitoring these result values. The noncontact type torque meter using silicone rubber that we're trying to develop this time is low-cost and can measure RPM and torque value simply. Also, it caculate a power using this value and indicate them on screen.

• 드라이브 ㆍ 컨트롤
• /
• 제13권1호
• /
• pp.10-17
• /
• 2016

e-4WD(Electric-4WD) system is a 4WD(4-Wheel Drive) System that can transform a car into a Hybrid System. e-4WD consists of a Motor, Inverter, Speed reducer and Clutch. The Motor, Speed reducer and Clutch are installed on the rear sub-frame as a chassis module type. The inverter is installed separately. Compared to a mechanical 4WD, the e-4WD system has many advantages. For example, the reduced number of drivetrain components makes better use of the space. Driving with a motor only at low speed improves fuel economy and reduces exhaust gas. Engine downsizing is available because the motor assists the engine. The performance of a conventional HEV(Hybrid Electric Vehicle) system can also be maintained. This paper proposes the specifications of components and the control logic for an e-4WD System. And the effect of the e-4WD system is proven using a test vehicle equipped with components under various test conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.540-543
• /
• 2002

Conventional robot manipulators actuated by motors with the speed reducer such as the harmonic drive have weakness in the load capacity, since the speed reducer does not have enough strength. To overcome this, we proposed and constructed a new type of the robot actuator which is four-bar-link mechanism driven by the ball screw. We developed a new type of a revolute-jointed robot manipulator composed of four axes. The base axis is actuated with conventional speed reducer, but the others are actuated by the proposed actuators. We analyzed the mechanism of the actuators of the robot joints, and developed the dynamics model. The dynamics are expressed in the joint coordinates, and then they are mapped into the sliding coordinates of the ball screw. The structure specifications of the manipulator shown.

• 동력기계공학회지
• /
• 제15권5호
• /
• pp.61-66
• /
• 2011

Recently, the speed reducer which is applied to robot has conducted a steady development on developments in the field of robotics. Among them, Harmonic drive is a high-stiffness, precision-controlled speed reducer and has high precision, compact, light in weight and high-reduction-ratio characteristics. The feature of flexspline of Harmonic Drive are two types. One is Cup type, the other is Silk Hat type. Silk Hat type is used in case of lighter and more compact in spatial because Silk Hat Type is hollow. According to the shape of silk hat, diaphragm is fractured because stress is concentrated. In this paper, the various shapes of silk hat are suggested to improve the durability of silk hat. And in the case of each shape, a study on stress and deformation using the FEM tool was carried out on flexspline.

• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.539-546
• /
• 2004

Conventional robot manipulators actuated by motors with the speed reducer such as the harmonic drive have weakness in the load capacity, since the speed reducer does not have enough strength. To overcome this, a new type of the robot actuator based on the four-bar-link mechanism driven by the ball screw was proposed and constructed. Also, a new type of a revolute-jointed robot manipulator composed of the developed actuators was developed. The base axis is actuated by the motor with the conventional speed reducer, but the other axes are actuated by the proposed actuators. The kinematics and dynamics of the robot were analyzed, and the performance test of the robot was made. Through the test results, the performance of superior load capacity versus the robot weight is shown.