• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.904-907
• /
• 2002

In this study, the plasma-assisted $CO_2$ conversion characteristics were investigated in the streamer corona discharge and silent discharge reactors with dielectric of $Al_2O_3$, to improve the conversion efficiency $CO_2$. Some discharge characteristics of $CO_2$ as parameters of gap spacing and applied voltage frequency, in both corona and silent discharge reactor were also obtained. The maximum $CO_2$ conversion rate was 10.1 [%] under the 5.2 [W] of discharge power and 250 [Hz] of applied voltage frequency.

• 태양에너지
• /
• 제1권1호
• /
• pp.30-36
• /
• 1981

Pool Boiling heat transfer from controlled arrays of artificial nucleation sites was studied experimentally. Distilled water were boiled from artificial sites of uniform size, shape and spacing, drilled in superfinished copper horizontal surfaces at site density of 16, 25, 36, 49, 64, 81, 100 per $2.25cm^2$. The results confirm the boiling heat transfer from artificial sites can be improved by increasing the site density N/A or temperature difference ${\Delta}T$ or both. Following experimental correlation were developed for predicting the heat transfer rate from the heating surface which has artificial sites. $$q/A = C(T_s - T_{sat})^{1.811}(N/A)^{0.41}$$

• 대한전자공학회논문지
• /
• 제26권11호
• /
• pp.1637-1643
• /
• 1989

In this study, phosphosilicate glass(PSG) film was deposited by the oxidation of phosphine (PH3) and silane(SiH4) in nitrogen ambient with a conventional conveyerized Atmospheric Pressure Chemical Vapor Deposition(APCVD)system and phosphorus concentration is measured by using FT-IR technique. The flow characteirstics and etch rate variations ofthe films, depending on phosphorus concentrations, are investigated. Special emphasis is focused on the yield variations of NMOS-based 256K DRAM with 1.2\ulcorner metallization spacing with increasing phosphorus concentrations. As a result, the data indicates that the fairly good yield can be obtained within the range of between 8 and 10wt% phosphorus concentration, which result in a slope of flow within 45\ulcorner10\ulcorner The analysi of failure mechanism is also accompanied.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.381-384
• /
• 2001

The combined stirring method to uniform distribution of particle is consisted of two strring force both electro-magnetic stirring generated from induction heating and mechanical stirring with graphite stirrer. PMMC billets were fabricated with the volume fractions ranged from 0% to 20% and particle sizes ranged from 14$\mu\textrm{m}$ to 25$\mu\textrm{m}$. It is important to control the size of primary ${\alpha}$-AI solid particles because it could become the cause of the particle pushing or capture phenomena from the fact that secondary dendrite arm spacing size depends on the cooling rate during the solidification in hypoeutectic AI-Si alloy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.629-630
• /
• 2006

• 대한기계학회논문집A
• /
• 제27권12호
• /
• pp.2055-2060
• /
• 2003

Striation is a typical pattern observed on the fatigue fracture surface and the spacing is known to correspond to a macroscopic fatigue crack growth rate, and many models for the predict in the formation of such striation have been proposed. However, these theories and methods can't be applied under random loading spectrum. In this study, the fatigue tests were carried out on aluminum alloy under random loading spectrum. The fatigue fracture surfaces were observed in the scanning electron microscope (SEM) and great quantities of SEM micrographs were synthesized and saved in computer system. The space and morphology of several large-scale striations, which are expected to from at the relatively greater load range in loading block, were observed. The crack length for each loading blocks was decided in consideration of regularity and repetition of those striations. It is shown that the applicability of fractographic methods on the fatigue fracture surface under random loading spectrum.

• 한국작물학회지
• /
• 제23권3호
• /
• pp.66-72
• /
• 1978

Cultural practices favoring the crops are one of the excellent weed control measures in upland crops. The primary cultural method for weed-management may include planting of weed-competitive cultivars, proper planting time and spacing, optimum rate and placement of fertilizer, crop rotation, mulching, and timely tillage. However, cultural method must be applied as a part of the program along with all other available means for controlling weeds since this method alone is not adequate. The efficient and economical weed control can only be achieved by combinating cultural, mechanical method that supplement each other into a weed management system. Intelligent selection of weed control, however, presuppose knowledge of the life history and growth requirements of the weed and its interaction with the environment.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.176-178
• /
• 2004

Gas tungsten arc welds on Al-4 wt% Cu alloys were investigated to determine effects of gravitational orientation on the weld solidification behavior. Outward convection flows in the parallel-down weld might be inhibited because of its reverse direction with respect to the gravity vector. This resulted in abnormal 'S' shape of the trailing s-1 interface and the solidification rate (Vs), which was receded toward the weld pool center. Significant influence of gravitational orientation resulted in the variation on the weld pool shape associated with convection flows, which in turn affected solidification orientation/morphology and the primary dendrite spacing(λ$_1$).

• Journal of information and communication convergence engineering
• /
• 제7권3호
• /
• pp.258-262
• /
• 2009

A Practical application of environmental monitoring system based on wireless sensor node network with the core of embedded system STR711FR2 microprocessor is presented in the paper. The adaptable and classifiable wireless sensor node network is used to achieve the data acquisition and multi-hop wireless communication of parameters of the monitoring base station environment including repeaters. The structure of the system is proposed and the hardware architecture of the system is designed, and the system operating procedures is proposed. As a result of field test, designed hardware platform operated with 50kbps bit rate and 5MHz channel spacing at 2040Hz. The wireless monitoring system can be managed and swiftly retreated without support of base station environmental monitoring.

• 대한전기학회논문지
• /
• 제38권8호
• /
• pp.650-657
• /
• 1989

The conversion efficiency of an ozone generator can be significantly improved by modifying the discharge electrode of a helical strip line rod-to-cylinder type ozone generator to a pyramid-project-embossed rod, and by using a pulse corona discharge. Parametric studies have been carried out to obtain optimum values of peak pulse voltage, pulse forming capacitance, feeder cable and ozone generator capacitance, interelectrode spacing and corona tip density of ozone generator, and feed air flow rate and temperature. The generated ozone concentration was very dependent upon the value of pulse forming capacitance, feeder cable and ozone generator capacitance, and corona tip density. Maximum conversion efficiency was obtained with a pulse forming capacitance of about 500pF, 75pF matched feeder cable and ozone generator, and a corona tip density of 16mm. When operated at optimum values, ozone yield of 79, 99, 80 g/KWh for the different interelectrode type ozone generators tested were obtained, which are approximately 30% higher than that of an industrial ozone generator.