• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.18 no.2
• /
• pp.10-21
• /
• 2022

A water source heat pump (WSHP) system is regarded as an energy-efficiency heating and cooling supply system for buildings due to its high energy efficiency and low greenhouse gas emissions. Recently, water sources such as river water, lake water, and raw water are attracting attention as heat sources for a heat pump system in Korea. This paper analyzed the applicability of a river water source heat pump system (RSHP). The river water temperature level was compared with the outdoor air and ground temperature levels to present applicability. In addition, the cooling and heating performance were compared through a simulation approach for the RSHP and a ground source heat pump (GSHP) applied to a large-scale office building. To compare the temperature level, the actual data were applied to the river water and the outdoor air, while the simulation results were applied to the ground circulation water. The results showed that the change in river water temperature throughout the year was similar to the change in outdoor air temperature. However, unlike the outdoor air temperature, the difference between the hourly and daily average river water temperatures was not large. The temperature level of river water was lower during the heating season and somewhat higher during the cooling season than that of the ground circulation water. Finally, the performance of the RSHP system was 13.4% lower than that of the GSHP system on an annual-based.

• Journal of the Korean Society of Costume
• /
• v.53 no.6
• /
• pp.75-86
• /
• 2003

The purpose of the study is to identify consumers' use of information source, store image, and demographic characteristics by their lifestyle types. and to establish a strategy for marketing and customer satisfaction management in order to response actively to the change of consumer behavior and to survive in this boundless competition. Out of the adult females who visited any discount store from October 3 to October 13. 2001. 300 women who would understand the purpose of the survey and respond it. were given with the questionnaire. Finally, 245 questionnaires were returned and analyzed. The data were processed in factor analysis. group analysis. deviation analysis. Duncan. and cross analysis. with SPSS WIN 10.0. The results are as follows: 1. Life style were categorized into 4 groups: social service pursuing group, fashion change pursuing group. convenience pursuing group, cultural life pursuing group. 2. There were some differences in discount store consumers's use of information source about the cosmetics according to lifestyle types. 3. There were some differences in discount store consumers's store image about the cosmetics according to lifestyle types. 4. There were some differences in discount store consumers's demographic characteristics about the cosmetics according to lifestyle types.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.8
• /
• pp.668-674
• /
• 2004

The possibility of global noise reduction by the sound power control through selection of distribution and impedance of absorptive materials is discussed. It is necessary to investigate the relation between the global sound energy in the field and the total sound power radiated by sources. In the previous work,$^{(1.2)}$ the authors presented a useful design method to change boundary condition that can be useful to reduce noise in acoustically small enclosures. Changing boundary condition Is related to not only enclosure’s geometrical shape but also acoustical treatment on walls for example, attaching of impedance patches (ex: absorptive material). In many practical situations, we often meet situation to change acoustical treatment on walls. The possibility of total acoustic potential energy(globa1 noise) reduction by acoustic source power control is examined in an acoustically small cavity Using acoustic energy balance equation, the relation between global noise control performance and absorptive material’s arrangement/impedance is deduced. Numerical simulation is performed to interpret its physical meaning in terms of absorbent’s distribution and impedance.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.1028-1031
• /
• 2004

Last target of architectural acoustics is that people wish to convey voice effectively from the space adaptively in use purpose in building. But, to how exactly through space sound source that wish to deliver from indoor can be passed does quantification sound estimation method is proposing various kinds physical parameter to estimate degree of voice definition (Speech articulation) and reverberation. Result that evaluate sound source about MLS signal and Impluse signal by pistol in this treatise could know that converge in MLS and measurement error extent about reverberation time(RT) of sound benevolent person. And value is thought there is problem showing change irregularly about sound benevolent person of D50, C80 etc. Finally, in case is spread sound field in difference of sound pressure level, when measure about change of sound pressure level, sound benevolent person could know that there is no different effect.

• Korean Journal of Optics and Photonics
• /
• v.14 no.4
• /
• pp.449-453
• /
• 2003

In a broadband erbium-doped fiber source for fiber optic gyroscope, a pump-polarization scrambling scheme is used to suppress the polarization dependence of the source mean wavelength. The degree of polarization of the pump is reduced to 1.4% by applying proper modulation depth to the polarization modulator where 10 m-long single-mode fiber is wound on a cylindrical PZT. In the case of using the pump-polarization scrambler as well as the output depolarizer, the mean-wavelength variations due to the random change of polarization are measured to be less than our measurement limit of 5 ppm.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.889-894
• /
• 2007

We investigated the quench velocity of superconducting fault current limiter (SFCL) dependent on the source voltage. $YBa_2Cu_3O_7$ (YBCO) thin film was used as the current limiting element for SFCL. The analysis on the quench velocity of SFCL is essential to determine the capacity of circuit breaker (CB) or coordinate with CB. Generally, the quench velocity of SFCL is related with the short-circuit current. To change the short-circuit current, in this paper, the amplitude of the power source voltage is adjusted. Through the fault current limiting experiments, the quench velocity of SFCL was confirmed to increase fast as the source voltage increased. On the other hand, the peak limited current was shown to increase with steady rate of increase.

• Electrical & Electronic Materials
• /
• v.8 no.5
• /
• pp.626-632
• /
• 1995

In this paper, The effect of the impedances in SNOSFET's memory devices has been developed. The effect of source and drain impedances measured by means of two bias resistances - field effect bias resistance by inner region, external bias resistance. The effect of the impedances by source and drain resistance shows the dependence of the function of voltages applied to the gate. It shows the differences of change in source drain voltage by means of low conductance state and high conductance state. It shows the delay of threshold voltages. The delay time of low conductance state and high conductance state by the impedances effect shows 3[.mu.sec] and 1[.mu.sec] respectively.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.13-14
• /
• 2008

A high rate magnetron sputtering source (HRMSS) was employed to deposit thick copper films. The HRMSS was manufactured by changing the magnet size, arrangement, and field intensity. For the preparation of thick copper films, the copper sputtering conditions using HRMSS were characterized based on the deposition parameters such as discharge characteristics, I-V characteristics of the source, and change of deposition rate. The deposition rate of copper turned out to be more than 5 times than that of conventional magnetron sputtering source. Thick copper films having thickness of more than $20{\mu}m$ were prepared by using HRMSS. The morphology and orientation of the films were investigated by scanning electron microscopy and x-ray diffraction.

• Journal of the Korea Furniture Society
• /
• v.28 no.3
• /
• pp.156-168
• /
• 2017

The digital information society that developed along with the 21st century is the 'Open-source Making Movement' which produces collective intelligence through open-source sharing and digital manufacturing tools, which is called 'Makers Movement'. The purpose of this paper is to analyze the case of Makers Movement in furniture design through 'IKEA Hacking' which arose simultaneously with the Makers Movement, and to study and present the prospect and direction of furniture design in the change of manufacturing industry. In this study, four design features were compared with IKEA hacking cases along with the establishment of 'community' which is a feature of Makers Movement. Four characteristics are first customized design, second derivative design through open source, third long -Tail effect design, and fourth, design using digital manufacturing tools. The prospect and direction of furniture design through this study are as follows: first, democratization of furniture design manufacturing, second job creation, third, coexistence of large and small enterprises, fourth promotion of various new technologies, and fifth, discovery of various furniture designers through 'Open System Organization'.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.242-242
• /
• 2009

Fabrication of Anodic aluminum oxide under DC vias condition has been studied. When bias and time of anodic aluminum oxide process change, the hole distance and diameter size change. Comparison of fabricated AAO between AC vias and DC vias condition has been studied in this experiment. The first and second anodization of one aluminum is done by using DC and AC power supplier. And first and second anodization of another aluminum is done by DC power supplier. The size of the aluminum is $1cm{\times}3cm$, and second anodic aluminum oxide process takes about 45min. It is found that the hexagonal shape appears on the surface of the AAO. AC power source can fabricate aao which have a nano hole array. We can see that the hole on the surface of the AC vias has a better rounded hole than DC vias AAO. we need more data so we can get characteristic about AC power generated AAO.