• Journal of the Korean Ceramic Society
• /
• v.45 no.12
• /
• pp.827-831
• /
• 2008

Spark plasma sintering (SPS) of AlN ceramics were carried out with ${Y_2}{O_3}$ as sintering additive at a sintering temperature $1,550{\sim}1,700^{\circ}C$. The effect of ${Y_2}{O_3}$ addition on sintering behavior and thermal conductivity of AlN ceramics was studied. ${Y_2}{O_3}$ added AlN showed higher densification rate than pure AlN noticeably, but the formation of yttrium aluminates phases by the solid-state reaction of ${Y_2}{O_3}$ and ${Al_2}{O_3}$ existed on AlN surface could delay the densification during the sintering process. The thermal conductivity of AlN specimens was promoted by the addition of ${Y_2}{O_3}$ up to 3 wt% in spite of the formation of YAG secondary phase in AlN grain boundaries because ${Y_2}{O_3}$ addition could reduced the oxygen contents in AlN lattice which is primary factor of thermal conductivity. However, the thermal conductivity rather decreased over 3 wt% addition because an immoderate formation of YAG phases in grain boundary could decrease thermal conductivity by a phonon scattering surpassing the contribution of ${Y_2}{O_3}$ addition.

• Korean Journal of Materials Research
• /
• v.30 no.2
• /
• pp.61-67
• /
• 2020

BiFeO₃ with perovskite structure is a well-known material that has both ferroelectric and antiferromagnetic properties called multiferroics. However, leaky electrical properties and difficulty of controlling stoichiometry due to Bi volatility and difficulty of obtaining high relative density due to high dependency on the ceramic process are issues for BiFeO₃ applications. In this work we investigated the sintering behavior of samples with different stoichiometries and sintering conditions. To understand the optimum sintering conditions, nonstoichiometric Bi_1±xFeO_3±δ ceramics and Ti-doped Bi_1.03Fe_1-4x/3Ti_xO₃ ceramics were synthesized by a conventional solid-state route. Dense single phase BiFeO₃ ceramics were successfully fabricated using a two-step sintering and quenching process. The effects of Bi volatility on microstructure were determined by Bi-excess and Ti doping. Bi-excess increased grain size, and Ti doping increased sintering temperature and decreased grain size. It should be noted that Ti-doping suppressed Bi volatility and stabilized the BiFeO₃ phase.

• The Korean Journal of Ceramics
• /
• v.5 no.3
• /
• pp.217-223
• /
• 1999

Proten-conductive $SrZr_{0.95} Y_{0.05} O_{2.975}$ powder was prepared by citrate gel method its characteristics and sinterability were investigated. Amorphous gel could be obtained from a citric acid solution that $SrCO_3$ and metal nitrates were dissolved. The initial decomposition of the gel proceeded up to $250^{\circ}C$, followed by combustion of its decomposition products in the temperature range from $250^{\circ}C$ to $500^{\circ}C$. A well-crystallized perovskite phase with a stoichiometric composition after calcination at $1000^{\circ}C$. Sintering green compacts of this powder for 6 h showed a considerable densification to start at $1200^{\circ}C$ and resulted in 86.8% and 96.5% relative densities at $1400^{\circ}C$ and $1600^{\circ}C$, respectively. Whereas, the powder compacts prepared by solid state reaction had much lower relative densities, 73% at $1400^{\circ}C$ and 92% at $1600^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.6
• /
• pp.536-540
• /
• 2007

The Ce-doped YAG(Yttrium Aluminum Garnet, $Y_3Al_5O_{12}$) phosphor powders were synthesized by combustion method. The luminescence, formation process and structure of phosphor powders were investigated by means of XRD, SEM and PL. The XRD patterns show that YAG Phase can form through sintering at $1000^{\circ}C$ for 2 h. This temperature is much lower than that required to synthesize YAG phase via the conventional solid state reaction method. There were no intermediate Phases such as YAP(Yttrium Aluminum Perovskite, $YAlO_3$) and YAM(Yttrium Aluminum Monoclinic, $Y_4Al_2sO_9$) observed in the sintering process. The powders absorbed excitation energy in the range $410{\sim}510\;nm$. Also, the crystalline YAG:Ce showed broad emission peaks in the range $480{\sim}600\;nm$ and had maximum intensity at 528 nm.

• Journal of the Korean Ceramic Society
• /
• v.56 no.4
• /
• pp.331-339
• /
• 2019

While high-temperature ceramic composites consisting of carbides, borides, and nitrides, the so-called ultra-high-temperature ceramics (UHTCs), have been commonly produced through solid-state sintering, melt-solidification is an alternative method for their manufacture. As many UHTCs are binary or ternary eutectic systems, they can be melted and solidified at a relatively low temperature via a eutectic reaction. The microstructure of the eutectic composites is typically rod-like or lamellar, as determined by the volume fraction of the second phase. Directional solidification can help fabricate more sophisticated UHTCs with highly aligned textures. This review describes the fabrication of UHTCs through the eutectic reaction and explains their mechanical properties. The use of melt-solidification has been limited to small specimens; however, the recently developed laser technology can melt large-sized UHTCs, suggesting their potential for practical applications. An example of laser melt-solidification of a eutectic ceramic composite is demonstrated.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.533-536
• /
• 2003

YIG(Yttrium Iron Garnet) is one of the most widely used ferrites for microwave telecommunication. It used as a passive devices such as isolators and circulators. In order to reduce the insertion losses of these passive devices, it is very important to reduce magnetic loss of the ferrites. In general, the magnetic losses of ferrites is closely related to the microstructure of the ceramics. In the sintering of YIG, pores are easily trapped in grains and grain boundaries. These pores cause to increase magnetic losses of the sinterted bodies. In this paper, the effect of the $SiO_2$ addition on the microstructure was discussed. Increasing the $SiO_2$ addition, the grain size was reduced, which means that added acts as a grain-growth inhibitor. During the sintering, $SiO_2$ settled down on the grain boundaries, and drag the grain growth. Therefore, there is enough time for pores to move out. The relative density of YIG sintered at $1350^{\circ}C$ with 1 mol% $SiO_2$ addition was 99.6%. $\Delta$H of these samples was under 50 Oe.

• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.1000-1005
• /
• 1997

The properties of ceramics by solid-state reaction with hydroxyapatite[$Ca_{10}(PO_4)_6(OH)_2$], which was isolated from tuna bone by wet milling process were investigated. The bulk density $2.93g/cm^3$ at $1350^{\circ}C$ was close to the calculated density $3.21g/cm^3$. On X-ray measurements, the major phases were identified as hydroxyapatite at below $1300^{\circ}C$, but the whitlockite [$Ca_3(PO_4)_2$] phases were appeared due to a decomposition of hydroxyapatite with temperature. The microstructures of sintering specimens were shown as small closed pores between grain boundaries. The mean bending strength of the sintered hydroxyapatite by solid-state reaction is about 58 MPa and this value is higher than that of the articular cartilage maximum strength, 40MPa.

• Applied Chemistry for Engineering
• /
• v.20 no.3
• /
• pp.317-321
• /
• 2009

In order to analyze the high temperature phase formation and the sinterability of super ionic conductor $K^+-{\beta}/{\beta}"-Al_2O_3$ which is commonly used as a solid oxide electrolyte, the pure $K^+-{\beta}/{\beta}"-Al_2O_3$ powder in the ternary system $K_2O-LiO_2-Al_2O_3$ was synthesized by solid state reaction and formed to tube and disk using slip casting method and cold isostatic pressing (CIP), respectively. The slip casting was conducted in an alumina mold with the slurry containing 40 wt% of solid contents and the CIP was carried out under 20 MPa. The samples were sintered at $1600^{\circ}C$, $1700^{\circ}C$ and $1750^{\circ}C$, respectively, and their phase formation and the sintering density were investigated according to the forming method. The samples produced by CIP showed far higher ${\beta}"-Al_2O_3$ fraction as compared with those by slip casting. On the other hand, the samples by slip casting showed slightly higher sintering density. The relative density reached to about 83% at $1750^{\circ}C$ and for 1 h, independent of the forming method. In the case of 90 min socking time, the density was decreased owing to the exaggerated grain growth and the pores by $K_2O$ evaporation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.5
• /
• pp.218-224
• /
• 2011

LAS ($Li_2O-Al_2O_3-SiO_2$) ceramics were sintered by a solid-state reaction. $CaCO_3$ and $ZrO_2$ were added to the ${\beta}$-spodumene ($Li_2O-Al_2O_3-4SiO_2$) composition of the LAS system for enhancement of sintering behavior and mechanical strength, respectively. We have investigated the sintering characteristics, microstructures, mechanical properties and thermal expansion characteristics according to the change of the amount of additive and sintering temperature of the ${\beta}$-spodumene. At 0.1 mol% $CaCO_3$, the densification of ${\beta}$-spodumene was significantly improved. At 0.04 mol% $ZrO_2$, the strength of ${\beta}$-spodumene was also improved. For all the selected all compositions, the thermal expansion coefficient was measured by a dilatometer, which revealed 1.2 to $1.7{\times}10^6/^{\circ}C$.

• Journal of the Korean Magnetics Society
• /
• v.24 no.2
• /
• pp.56-59
• /
• 2014

The samples of $Ba_2CoZnFe_{12}O_{22}$ was synthesized by the solid-state reaction method. The toroids of $Ba_2CoZnFe_{12}O_{22}$ were sintered with various sintering temperature at 1050, 1100, 1150, and $1200^{\circ}C$, and studied by x-ray diffractometer, vibrating sample magnetometer, network analyzer, and Mssbauer spectrometer. From the XRD patterns, the density of samples increased with increasing sintering temperature. From the magnetic hysteresis curves up to 10 kOe at 295 K, the saturation magnetization ($M_s$) of $Ba_2CoZnFe_{12}O_{22}$ samples in various sintered at 1050, 1100, 1150 ,and $1200^{\circ}C$ were showed around $M_s$= 33.0 emu/g. However, With increasing sintering temperature, the coercivity ($H_c$) of samples decrease. Complex permeability and permittivity of samples in various sintering temperatures were measured between 100MHz to 4 GHz. With increasing sintering temperature, the permeability of samples increase.