• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.510-510
• /
• 2007

Titanate nanotube(TNT)는 높은 비표면적과 우수한 물리화학적 특성을 가지고 있어 광촉매, 수소 저장재료, 태양전지용 전극재료 등에 적용되고 있다. 또한, 티타네이트 나노튜브는 전자 이동이 원활한 구조적 특징을 가지고 있어 리듐 이차전지용 호스트 재료로서 많은 연구가 진행 중이다. 이에 본 연구에서는 저온균일침전법으로 제조한 루틸상 $TiO_2$ 분말에 Lithium chloride를 1~10wt%를 동시에 첨가한 후 10M의 sodium hydroxide 수용액 내에서 수열합성하여 리튬이 도핑된 티타네이트 나노튜브를 제조하였다. 제조된 분말의 입자형상 및 크기는 전자주사 현미경을 이용하여 관찰하였으며, X-선 회절분석을 이용하여 리튬 첨가에 따른 결정상 변화를 관찰하였다. 또한 리튬이 도핑된 티타네이트 나노튜브의 전기화학적 특성 평가를 위해 양극 활물질 : 도전제 : 바인더를 75 : 20 : 5의 비율로 혼합한 후 coin cell을 제조하였고, potentiostat를 이용하여 용량 측정 및 cycle 특성을 실시하였다. 수열 합성법에 의해 형성된 입자는 직경 10nm, 길이 수 ${\mu}m$로 관찰되었으며, X-선 회절 시험 결과 LiO와 같은 이차상은 발견되지 않았다. 측정된 coin cell의 용량은 240mAh/g을 나타내었으나, 싸이클 특성이 빠르게 저하됨을 확인할 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.189-189
• /
• 2008

Due to the environmental issue vast research is going on to replace the widely used lead contented piezoelectric materials. Bismuth sodium titanate (abbreviated as BNT) based bismuth sodium titanate-barium titanate (abbreviated as BNBT) ceramic was prepared by using modified method rather than conventional mixed oxide method. This modification was made to improve the properties of BNT based ceramic. In this procedure $BaTiO_3$ (abbreviated as BT) was prepared using conventional mixed oxide method. Analytical grade raw materials of $BaCO_3$ and $TiO_2$ were weighted and ball milled using ethanol medium. The mixed slurry was dried and sieved under 80 mesh. Then the powder was calcined at $1100^{\circ}C$ for 2 hours. This calcined BT powder was used in the preparation of BNBT. Stoichiometric amount of $Bi_2O_3$, $Na_2CO_3$, $TiO_2$ and BT were weighted and mixed by using ball mill. The used calcination temperature was $850^{\circ}C$ for 2 hours. Calcined powder was taken for another milling step. BNBT disks were pressed to 15 mm of diameter and then cold isostatical press (CIP) was used. Pressed samples were sintered at $1150^{\circ}C$ for 2 hours. The SEM microstructure analysis revealed that the grain shape of the sintered ceramic was polyhedral and grain boundary was well matched where as the sample prepared by conventional method showed irregular arrangement and grain boundary not well matched. And sintered density was better (5.78 g/cc) for the modified method. It was strongly observed that the properties of BNBT ceramic near MPB composition was found to be improved by the modified method compare to the conventional mixed oxide method. The piezoelectric constant dB of 177.33 pC/N, electromechanical coupling factor $k_p$ of 33.4%, dielectric constant $K_{33}^T$ of 688.237 and mechanical quality factor $Q_m$ of 109.37 was found.

• The Korean Journal of Ceramics
• /
• v.1 no.2
• /
• pp.69-74
• /
• 1995

The optimal condition for minimal agglomeration of barium titanyl oxalate tetrahydrate, the precipitate on preparing barium titanate by oxalate process, was investigated. Burette-dropping and dual-nozzle-spraying were used as adding methods. pH of washing water for precipitates was changed, and sodium pyrophosphate solution, methanol, ethoanol, and acetone were used as washing agents for precipitates, as well as distilled water. Drying temperature was changed from $50^{\circ}C$ to $120^{\circ}C$. Spraying, methanol-washing, and drying at $60^{\circ}C$ showed the most dispersed distribution, Below $70^{\circ}C$, the crystalline phases were observed.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.13 no.1
• /
• pp.15-28
• /
• 1987

Silica spheres were prepared by interfacial reaction method. Factors in-fluencing to the mean particle size and specific surface area of silica spheres were investigated. The experiment about the surface modification of silica spheres was carried out. It was observed that silica spheres have characteristics of the spherical shape with the vacancy in the inner side, high surface area, and reaction tendency by many silanol group. The mean particle size of silica spheres is dependent on the surfactant concentration and W/O ratio. The specific surface area is influenced by SiO2/Na2O mole ratio in sodium silicate. Silica spheres coated with titanium dioxide or zirconium dioxide improve the UV protection effect. Titanate and silane coupling agent make chemical bond with silica surface and improve the organophile and the dispersibility of silica spheres.

• Journal of the Korean Chemical Society
• /
• v.49 no.6
• /
• pp.560-566
• /
• 2005

Sintered ceramic samples of pure and some copper doped layered sodium lithium tri-titanate ($Na_{1.9}Li_{0.1}Ti_{3-X}Cu_XO_{7-X}$) materials with different dopant molar percentages (0.0$Cu^{2+}$ at $Ti^{4+}$ sites in the lattice is proposed in this paper. Furthermore, three distinct regions have been identified in log(${\sigma}_{d.c.}T$) versus 1000/T plots. The lowest temperature region is attributed to electronic hopping conduction(polaron) for all copper doped derivatives and ionic conduction for lithium substituted $Na_2Ti_3O_7$.The mechanism of conduction in the intermediate region is associated interlayer ionic conduction and in the highest temperature region is associated modified interlayer ionic conduction.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.4
• /
• pp.25-30
• /
• 2013

Pb-free ferroelectric $(Na_{0.5}Bi_{0.5})TiO_3$ (NBT) thin films were prepared by a modified sol-gel process. Their structural, dielectric and pyroelectric properties were investigated as a function of the excess Na/Bi ratio and the annealing temperature. In the case of thin films containing no excess Na and Bi, only partial amounts of the perovskite NBT were crystallized, where the films consisted mainly of the pyrochlore phase of $Bi_2Ti_2O_7$ for annealing conditions of $600{\sim}800^{\circ}C$. With increasing excess Na/Bi ratio, the proportion of the perovskite phase effectively increased due to the compensation of the volatile Na and Bi components. For a Na/Bi ratio of 2.0, the thin film with single NBT perovskite phase was obtained within XRD detection limit after annealing at $700^{\circ}C$ for 10 min and it showed the excellent dielectric properties, ${\varepsilon}r$ of ~550 and tan ${\delta}$ of 0.03. While these properties were degraded for Na/Bi ratio of 2.5 despite the existence of pure perovskite phase. The NBT thin film with Na/Bi ratio of 2.0 are also promising candidates for applications requiring pyroelectric devices because it was found to have pyroelectric coefficients of $1.3{\sim}7nC/cm^2K$ in the temperature range of $30{\sim}100^{\circ}C$.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.64-67
• /
• 2011

The effect of Ta substitution on the crystal structure, ferroelectric, and piezoelectric properties of $Bi_{0.5}(Na_{0.82}K_{0.18})_{0.5}Ti_{1-x}Ta_xO_3$ ceramics has been investigated. The Ta doping resulted in a transition from coexistence of ferroelectric tetragonal and rhombohedral phases to an electrostrictive pseudocubic phase, leading to degradations of the remnant polarization, coercive field, and piezoelectric coefficient $d_{33}$. However, the electricfield-induced strain was significantly enhanced by the Ta substitution-induced phase transition and reached a highest value of $S_{max}/E_{max}$ = 566 pm/V under an applied electric field 6 kV/mm when 2% Ta was substituted on Ti sites. The abnormal enhancement in strain was attributed to the pseudocubic phase with high electrostrictive constants.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.1
• /
• pp.1-6
• /
• 2017

A comparative study of microwave and conventional sintering of lead-free $Bi_{1/2}(Na_{0.82}K_{0.18})_{1/2}TiO_3-BaZrO_3-CuO$ ceramics is presented. It was found that microwave sintering (MWS) can be successfully applied to the fabrication of large strain Bi-perovskite with electric field-induced strains comparable to those obtained with conventional sintering (CFS). Although MWS resulted in smaller grained microstructures than CFS, the ferroelectric properties were stronger in MWS-derived specimens than in the CFS-derived ones. The piezoelectric strain constant $d_{33}{^*}$ of the CFS-derived specimens reached a maximum value of 372 pm/V after sintering at $1100^{\circ}C$, whereas that of MWS-derived specimens peaked at $950^{\circ}C$ with a $d_{33}{^*}$ value of 324 pm/V.

• Journal of Powder Materials
• /
• v.17 no.5
• /
• pp.399-403
• /
• 2010

The effects of $MnO_2$ doping on the crystal structure, ferroelectric, and piezoelectric properties of (K,Na)$NbO_3$ (KNN) ceramics have been investigated. $MnO_2$ was found to be effective in enhancing the densification and grain growth during sintering. X-ray diffraction analysis indicated that Mn ions substituted B-site Nb ions up to 2 mol%, however, further doping induced unwanted secondary phases. In comparison with undoped KNN ceramics, the well developed microstructure and the substitution to B-sites in 2 mol% Mn-doped KNN ceramics resulted in significant improvements in both piezoelectric coupling coefficient and electromechanical quality factor.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.12a
• /
• pp.123-125
• /
• 2006

The $TiO_2$ sol was prepared hydrothermally in an autoclave from aqueous $TiOCl_2$ solutions as a starting precursor. Hollow fibers were obtained when the sol-gel-derived $TiO_2$ sol was treated chemically with a NaOH solution and subsequently heated in the autoclave under various conditions. A systematic analysis of the influence of different NaOH concentrations on the formation of nanotubes was carried out. The details of the nanotubular structure were investigated by using transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). From the TEM images, the outer and the inner diameters of the tubes were measured to be about 8 and 4 nm, respectively, the lengths were measured to be several hundreds of nanometers.