• 한국진공학회지
• /
• 제5권1호
• /
• pp.54-61
• /
• 1996

Indium-tin oxide (ITO) films were deposited on the glass substrate by the reactive -ionized cluster beam deposition(ICBD) method. In the oxygen atmosphere, indium cluster formed through the nozzle is ionized by the electron bombardment and is accelerated to be deposited on the substrate. And tin is simultaneoulsy evaporated from the boron-nitride crucible. The chracteristics of films were examined by the X-ray photoelectron spectroscopy(XPS), glancing angle X-ray diffractrion(GXRD) and the electrical properties. were measured by 4-point-probe and Hall effect measurement system . From the XPS spectrum , it was found that indium and tin atoms combined with the oxygen to form oxide$(In_2O_3, SnO_2)$. In the case of films with high tin-concentration, the GXRD spectra show that the main $In_2O_3$ peak of (222) plane, but also sub peaks((440) peak etc.) and $SnO_2$ peaks were detected. From that results, itis concluded that the heavily dopped tin component (more than 14 at. %) disturbs to form $In_2O_3$(222) phase. Four-point-probe and Hall effect measurement show that, in the most desirable case, the transmittance of the films is more then 90% in visible range and its resistivity is $$\rho$=3.55 \times10^{-4}\Omega$cm and its mobility is $\mu$=42.8 $\textrm{cm}^2$/Vsec.

• 반도체디스플레이기술학회지
• /
• 제9권4호
• /
• pp.83-86
• /
• 2010

The transparent electrode properties of ITO films deposited by RF magnetron sputtering with process pressure were investigated. The ITO thin films was deposited on a glass substrate using a target with 3in diameter sintered at a ratio of $In_2O_3$ : $SnO_2$ (9 : 1). 200-nm-thick ITO thin films were manufactured by various process pressures ($2.0{\times}10^{-2}$, $7.0{\times}10^{-3}$ and $2.0{\times}10^{-3}$ Torr). The optical transmittance and resistivity of the deposited ITO thin films showed a relatively satisfactory result under $10^{-2}$ Torr. For high process pressure, the optical transmittance was below 80%, while for low process pressure, the optical transmittance was above 85%. As a result of of mobility, resistivity and carrier concentration by Hall measurement, we obtained satisfactory properties to apply into a transparent conducting thin film.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2009년도 추계학술대회
• /
• pp.910-912
• /
• 2009

투명전극은 비저항이 $1{\times}10^{-3}{\Omega}/cm$이하, 면저항이 $10^3{\Omega}/sq$이하로 전기전도성이 우수하고 380에서 780nm의 가시광선 영역에서의 투과율이 80%이상이라는 두 가지 성질을 만족시키는 박막이다. 기존의 평판디스플레이의 경우, 금속 산화물 투명전극이 진공 증착 공정을 통해 도포된 유리기판상의 각 화소를 포토리소그래피 공정으로 제조된 박막트랜지스터(TFT : Thin Film Transistor)로 제어함으로써 화상을 구현한다. 본 연구에서는 스퍼터링 진공 증착 장치를 이용하여 투명 도전막(ITO: Indium Tin Oxide)을 제작하고 제작된 ITO 박막의 광 및 전기 그리고 물성적 특성을 조사하여 최상의 공정 조건을 확립하였다. a-Si:H 박막위에 형성되는 ITo 박막은 a-Si:H 박막의 특성상 온도 및 스퍼터링 전력에 대한 연구가 주요 문제이다. 본 실험에서는 $In_2O_3:SnO_2$의 조성비는 90:10 wt% 인 타겟의 특성이 우수하였고, $Ar:O_2$의 분압비는 100:1 및 42:8 의 조건이 적당하였으며, 온도는 $200^{\circ}C$ 가장 우수한 특성을 얻을 수 있었다. $200^{\circ}C$ 는 비정질 실리콘의 성능에 좋은 영향을 미치는 온도이며, 알려진 것과 같이 $23^{\circ}C$ 즉 실온의 경우에 비해 막의 균질성 및 특성이 우수 한 것을 알 수 있었다. 본 연구에서 제작한 박막은 광 투과도가 90% 이상, 비저항이 $300{\mu}{\Omega}cm$ 이하의 특성을 갖게되어 이미지센서, 태양전지, 액정 텔레비젼등 빛의 통과와 전도성등 두가지 특성에 동시에 만족 될만한 성능을 가질 수 있음을 확인하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.42.2-42.2
• /
• 2010

Transparent conducting oxides (TCOs) are of significant importance for their applications in various devices, such as light-emitting diodes, thin-film solar cells, organic light-emitting diodes, liquid crystal displays, and so on. In order for TCOs to contribute to the performance improvement of these devices, TCOs should have high transmittance and good electrical properties simultaneously. Sn-doped $In_2O_3$ (ITO) is the most commonly used TCO. However, indium is toxic and scarce in nature. Thus, ZnO has attracted a lot of attention because of the possibility for replacing ITO. In particular, group III impurity-doped ZnO showed the optoelectronic properties comparable to those of ITO electrodes. Al-doped ZnO exhibited the best performance among various doped ZnO films because of the high substitutional doping efficiency. However, in order for the Al-doped ZnO to replace ITO in electronic devices, their electrical and optical properties should further significantly be improved. In this connection, different ways such as a variation of deposition conditions, different deposition techniques, and post-deposition annealing processes have been investigated so far. Among the deposition methods, RF magnetron sputtering has been extensively used because of the easiness in controlling deposition parameters and its fast deposition rate. In addition, when combined with post-deposition annealing in a reducing ambient, the optoelectronic properties of Al-doped ZnO films were found to be further improved. In this presentation, we deposited Al-doped ZnO (ZnO:$Al_2O_3$ = 98:2 wt%) thin films on the glass and sapphire substrates using RF magnetron sputtering as a function of substrate temperature. In addition, the ZnO samples were annealed in different conditions, e.g., rapid thermal annealing (RTA) at $900^{\circ}C$ in $N_2$ ambient for 1 min, tube-furnace annealing at $500^{\circ}C$ in $N_2:H_2$=9:1 gas flow for 1 hour, or RTA combined with tube-furnace annealing. It is found that the mobilities and carrier concentrations of the samples are dependent on growth temperature followed by one of three subsequent post-deposition annealing conditions.

• Korean Chemical Engineering Research
• /
• 제43권1호
• /
• pp.85-91
• /
• 2005

ECR-MOCVD를 이용한 상온조건에서 투명전도성 고분자막이$(CH_3)_4Sn-H_2-O_2$ 분위기하에 $SnO_2$막이 제조되었다. 제조된 투명전도막의 전기적특성은 공정압력, 전자석/분사링/기판사이의 거리, 전자석의 전류, 마이크로파 출력, 증착시간과 같은 공정변수에 따라 조사되었다. 마이크로파 출력과 전자석의 전류가 증가함에 따라 낮은 전기적 저항을 갖는 $SnO_2$막이 형성되었다. 또한 이들 공정변수들이 증착된 막의 광학적특성에 미치는 영향은 중요하게 나타났다. ECR-MOCVD에 의해 제조된 막의 투과도와 반사도는 380-780 nm의 가시광영역에서 각각 93-98%, 0.1-0.5%였다. 증착된 막의 평균 grain 크기는 공정변수에 관계없이 20-50 nm범위의 값으로 일정하였다. 본 연구의 최적화된 조건에서 전기적저항은 $7.5{\times}10^{-3}ohm{\cdot}cm$, 투과도 93%, 반사도 0.2%를 갖는 막이 얻어졌다.

• 한국분말재료학회지
• /
• 제22권5호
• /
• pp.321-325
• /
• 2015

The triboelectric property of a material is important to improve an efficiency of triboelectric generator (TEG) in energy harvesting from an ambient energy. In this study, we have studied the TEG property of a semiconducting $SnO_2$ which has yet to be explored so far. As a counter triboelectric material, PET and glass are used. Vertical contact mode is utilized to evaluate the TEG efficiency. $SnO_2$ thin film is deposited by atomic layer deposition on bare Si wafer for various thicknesses from 5.2 nm to 34.6 nm, where the TEG output is increased from 13.9V to 73.5V. Triboelectric series are determined by comparing the polarity of output voltage of 2 samples among $SnO_2$, PET, and glass. In conclusion, $SnO_2$, as an intrinsic n-type material, has the most strong tendency to be positive side to lose the electron and PET has the most strong tendency to be negative side to get the electron, and glass to be between them. Therefore, the $SnO_2$-PET combination shows the highest TEG efficiency.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.383-384
• /
• 2008

$SnO_2$ oxides are considerable interest for the development of transparent electrode, thin film resistor and gas sensors. Electrospinning is a class of nanofiber forming processes by which electrostatic forces are employed to control the production of nanofibers. In this study, antimony doped tin oxide thin films were prepared by electrospinning process. Effects of ATO doping concentration and applied voltage on electrical and light transmission properties were investigated.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.180-180
• /
• 2010

Thin film transistors (TFTs) based on oxide semiconductors have emerged as a promising technology, particularly for active-matrix TFT-based backplanes. Currently, an amorphous oxide semiconductor, such as InGaZnO, has been adopted as the channel layer due to its higher electron mobility. However, accurate and repeatable control of this complex material in mass production is not easy. Therefore, simpler polycrystalline materials, such as ZnO and $SnO_2$, remain possible candidates as the channel layer. Inparticular, ZnO-based TFTs have attracted considerable attention, because of their superior properties that include wide bandgap (3.37eV), transparency, and high field effect mobility when compared with conventional amorphous silicon and polycrystalline silicon TFTs. There are some technical challenges to overcome to achieve manufacturability of ZnO-based TFTs. One of the problems, the stability of ZnO-based TFTs, is as yet unsolved since ZnO-based TFTs usually contain defects in the ZnO channel layer and deep level defects in the channel/dielectric interface that cause problems in device operation. The quality of the interface between the channel and dielectric plays a crucial role in transistor performance, and several insulators have been reported that reduce the number of defects in the channel and the interfacial charge trap defects. Additionally, ZnO TFTs using a high quality interface fabricated by a two step atomic layer deposition (ALD) process showed improvement in device performance In this study, we report the fabrication of high performance ZnO TFTs with a $Si_3N_4$ gate insulator treated using plasma. The interface treatment using electron cyclotron resonance (ECR) $O_2$ plasma improves the interface quality by lowering the interface trap density. This process can be easily adapted for industrial applications because the device structure and fabrication process in this paper are compatible with those of a-Si TFTs.

• Transactions on Electrical and Electronic Materials
• /
• 제15권6호
• /
• pp.328-332
• /
• 2014

Thin film transistors (TFTs) with an amorphous silicon zinc tin oxide (a-2SZTO) channel layer have been fabricated using an RF magnetron sputtering system. The effect of the change of excitation electron on the variation of the total interfacial trap states of a-2SZTO systems was investigated depending on sputtering power, since the interfacial state could be changed by changing sputtering power. It is well known that Si can effectively reduce the generation of the oxygen vacancies. However, The a-2SZTO systems of ZTO doped with 2 wt% Si could be degraded because the Si peripheral electron belonging to a p-orbital affects the amorphous zinc tin oxide (a-ZTO) TFTs of the s-orbital overlap structure. We fabricated amorphous 2 wt% Si-doped ZnSnO (a-2SZTO) TFTs using an RF magnetron sputtering system. The a-2SZTO TFTs show an improvement of the electrical property with increasing power. The a-2SZTO TFTs fabricated at a power of 30 W showed many of the total interfacial trap states. The a-2SZTO TFTs at a power of 30 W showed poor electrical property. However, at 50 W power, the total interfacial trap states showed improvement. In addition, the improved total interfacial states affected the thermal stress of a-2SZTO TFTs. Therefore, a-2SZTO TFTs fabricated at 50 W power showed a relatively small shift of threshold voltage. Similarly, the activation energy of a-2SZTO TFTs fabricated at 50 W power exhibits a relatively large falling rate (0.0475 eV/V) with a relatively high activation energy, which means that the a-2SZTO TFTs fabricated at 50 W power has a relatively lower trap density than other power cases. As a result, the electrical characteristics of a-2SZTO TFTs fabricated at a sputtering power of 50 W are enhanced. The TFTs fabricated by rf sputter should be carefully optimized to provide better stability for a-2SZTO in terms of the sputtering power, which is closely related to the interfacial trap states.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.37-40
• /
• 2009

불소가 도핑된 산화주석(SnO2:F, FTO) 박막은 다결정 전도성 세라믹으로 가시광선 영역에서 투명하기 때문에 태양전지의 전극으로 활용된다. 본 연구에서 FTO는 APCVD법으로 성막되었다. BSG기판을 사용하여 $620^{\circ}C$의 고온에서 공정이 진행되었다. 이렇게 제작된 FTO 박막은 수소, 질소, 대기 분위기에서 여러 열처리 시간을 변수로 실험하여 열처리 전후의 전기적, 광학적, 구조적 변화를 관찰하고 분석하였다. 전기적 특성 분석에는 전기 비저항, 모빌리티 및 캐리어 농도 등의 변화를 알아보았고, 광학적 분석에는 UV-vis spectoscopy로 200nm에서 800nm 파장대역의 투과도를 구하고, Hazemeter를 통하여 총투과율, 평행투과율, 확산투과율 및 Haze를 분석하여 FTO막이 가지고 있는 texturing에 의한 효과를 알아보기 위하여 시편의 열처리 전후를 비교 분석하였다. 구조적 분석은 XRD를 이용하여 pattern을 분석하여 FTO가 가지는 구조변화를 분석하였다. 특히 FTO의 texturing에 기여도가 높은 (200)면의 XRD peak강도가 상승함에 따라 후열처리에 의해 박막의 표면의 변화가 일어남을 확인하였다. FTO의 후열처리에 의한 변화는 전기적으로는 약간의 전기 비저항의 증가를 가져오며, 캐리어 농도의 감소를 가져온다. 캐리어 농도의 감소에 따라 모빌리티의 상승이 관찰되었다. 광학적 특성은 가시광선 영역에서 투과율은 거의 같거나 약간 감소하는 경향을 나타내며, 후열처리 전후에 거의 동일한 투과율을 보이면서도 확산 투과율이 상승하는 분석 결과를 얻었다.