• New & Renewable Energy
• /
• v.18 no.2
• /
• pp.40-49
• /
• 2022

In this study, the phase and electrochemical properties of Co and Ti substituted layered perovskites SmBaCo_2-xTi_xO_5+d (x=0.5, 0.7, 1.0, 1.1, 1.3, and 1.5) were analyzed, and their application as electrodes in solid oxide fuel cells (SOFCs) were evaluated. After calcination at 1300℃ for 6 h, a single phase was observed for two compositions of the SmBaCo_2-xTi_xO_5+d oxide system, SmBaCoTiO_5+d (x=1.0) and SmBaCo_0.9Ti_1.1O_5+d (x=1.1). However, the phases of SmBaCoTiO_5+d (SBCTO) and SmTiO₃ coexisted for compositions with x≥1.3 (Ti content). In contrast, for compositions of x≤0.7, the SmBaCo₂O_5+d phase was observed instead of the SmTiO₃ phase. To evaluate the applicability of these materials as SOFC electrodes, the electrical conductivities were measured under various atmospheres (air, N₂, and H₂). SBCTO exhibited stable semi-conductor electrical conductivity behavior in an air and N₂ atmosphere. However, SBCTO showed insulator behavior at temperatures above 600℃ in a H₂ atmosphere. Therefore, SBCTO may only be used as cathode materials. Moreover, SBCTO had an area specific resistance (ASR) value of 0.140 Ω·cm² at 750℃.

• Journal of Magnetics
• /
• v.8 no.3
• /
• pp.124-127
• /
• 2003

HDDR (hydrogenation, disproportionation, desorption, recombination) and mechanical milling processes have been applied to the $SmCo_{5}$ alloy in an attempt to produce a highly coercive powder. The $SmCo_{5}$ alloy had very high structural stability under the hydrogen atmosphere and the 1:5 phase was only partially disproportionated under up to 10 kgf/$\textrm{cm}^2$ hydrogen gas. The partially disproportionated material was recombined not into 1:5 phase after the HDDR, but rather into multi-phase mixture consisting of 1:5, 2:17, 2:7 and 1:7 phases. The $SmCo_{5}$ alloy HDDR-treated with hydrogen up to 10 kgf/$\textrm{cm}^2$ had poor coercivity. For a useful HDDR to prepare a high coercivity $SmCo_{5}$ alloy powder, much higher hydrogen pressure well exceeding 10 kgf/$\textrm{cm}^2$ would be required. The $SmCo_{5}$ alloy lump was amorphized by an intensive mechanical milling, and it was crystallised ultra-finely by a subsequent optimum annealing. The optimally annealed material had very high coercivity, and it was found that the mechanical milling followed by an annealing was an effective way of producing highly coercive $SmCo_{5}$ alloy powder.

• Journal of the Korean Magnetics Society
• /
• v.12 no.5
• /
• pp.189-194
• /
• 2002

Microstructure and magnetic properties of Sm-Co sintered magnet were investigated with the variation of Zr content and their solution treatment and aging temperatures. The fraction of eutectic structure and the size of eutectic area decreased with increasing x value of cast Sm(C $O_{.688-x}$F $e_{.242}$C $u_{.07}$Z $r_{x}$)$_{7.404}$ alloys. On the other hand, x=0.022 ingot had finer dendritic structure compared to the other alloys. The sintered magnet of Sm(C $O_{.688-x}$F $e_{.242}$C $u_{.07}$Z $r_{x}$)$_{7.404}$ had well defined cell structure which is composed of cell boundary Sm $Co_{5}$ and cell interior S $m_2$Co/ssub 17/ phase. Cell boundary Sm $Co_{5}$ phase has 20nm thickness and its relative angle was 120$^{\circ}$ in x=0.018 and 0.022 alloys. Cell size was decreased with increasing Zr contents. But, x=0.026 alloy has diffuse cell boundary and irregular shape compared to x=0.022 and 0.018 alloys. Maximum value of coercive force and maximum energy Product were obtained from x=0.022 alloys. Optimum solution treatment temperature of Sm(C $O_{.688-x}$F $e_{.242}$C $u_{.07}$Z $r_{x}$)$_{7.404}$ alloy was 1170 $^{\circ}C$ and 1st aging temperature of two step aging process for higher coercivity was 850 $^{\circ}C$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.5
• /
• pp.393-399
• /
• 2020

A series of phosphors, SrWO₄:5 mol% Dy³⁺, SrWO₄:5 mol% Sm³⁺, and SrWO₄:5 mol% Dy³⁺:x Sm³⁺ (x＝1~15 mol%), were prepared using a facile co-precipitation. The crystal structure, morphology, photoluminescence properties, and application in anti-counterfeiting fields were investigated. The crystalline structures of the prepared phosphors were found to be tetragonal systems with the dominant peak occurring at the (112) plane. The excitation spectra of the Dy³⁺ singly-doped SrWO₄ phosphors were composed of an intense charge-transfer band centered at 246 nm in the range of 210~270 nm and two weak peaks at 351 nm and 387 nm due to the ⁶H_15/2→⁶P_7/2 and ⁶H_15/2→⁴I_13/2 transitions of Dy³⁺ ions, respectively. The wavelength of 246 nm was optimum for exciting the luminescence of Dy³⁺ and Sm³⁺ co-doped SrWO₄ phosphors. The emission spectra consisted of two intense blue and yellow emission bands at 480 nm and 573 nm corresponding to the ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transitions of Dy³⁺, and two strong emission peaks at 599 nm and 643 nm originating from the ⁴G_5/2→⁶H_7/2 and ⁴G_5/2→⁶H_9/2 transitions of Sm³⁺, respectively. As the concentration of Sm³⁺ ions increased, the emission intensities of Dy³⁺ rapidly decreased, while the emission intensities of Sm³⁺ gradually increased. These results suggest that the color of the emission light can be tuned from yellow to white by changing the concentration of Sm³⁺ ions at a fixed 5 mol% Dy³⁺. Furthermore, the fluorescent security inks were synthesized for use in anti-counterfeiting applications.

• Korean Journal of Materials Research
• /
• v.30 no.8
• /
• pp.406-412
• /
• 2020

SrMoO₄:RE³⁺ (RE=Dy, Sm, Tb, Eu, Dy/Sm) phosphors are prepared by co-precipitation method. The effects of the type and the molar ratio of activator ions on the structural, morphological, and optical properties of the phosphor particles are investigated. X-ray diffraction data reveal that all the phosphors have a tetragonal system with a main (112) diffraction peak. The emission spectra of the SrMoO₄ phosphors doped with several activator ions indicate different multicolor emissions: strong yellow-emitting light at 573 nm for Dy³⁺, red light at 643 nm for Sm³⁺, green light at 545 nm for Tb³⁺, and reddish orange light at 614 nm for Eu³⁺ activator ions. The Dy³⁺ singly-doped SrMoO₄ phosphor shows two dominant emission peaks at 479 and 573 nm corresponding to the ⁴F_9/2→⁶H_15/2 magnetic dipole transition and ⁴F_9/2→⁶H_13/2 electric dipole transition, respectively. For Dy³⁺ and Sm³⁺ doubly-doped SrMoO₄ phosphors, two kinds of emission peaks are observed. The two emission peaks at 479 and 573 nm are attributed to ⁴F_9/2→⁶H_15/2 and ⁴F_9/2→⁶H_13/2 transitions of Dy³⁺ and two emission bands centered at 599 and 643 nm are ascribed to ⁴G_5/2→⁶H_7/2 and ⁴G_5/2→⁶H_9/2 transitions of Sm³⁺. As the concentration of Sm³⁺ increases from 1 to 5 mol%, the intensities of the emission bands of Dy³⁺ gradually decrease; those of Sm³⁺ slowly increase and reach maxima at 5 mol% of Sm³⁺ ions, and then rapidly decrease with increasing molar ratio of Sm³⁺ ions due to the concentration quenching effect. Fluorescent security inks based on as-prepared phosphors are synthesized and designed to demonstrate an anti-counterfeiting application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.1
• /
• pp.39-45
• /
• 2003

The varistor properties of ZnO-Pr$_{6}$O$_{11}$-CoO-based ceramics doped with Sm$_2$O$_3$were investigated in the addition range of 0.0~2.0 mol% Sm$_2$O$_3$at sintering temperature of 130$0^{\circ}C$ and 135$0^{\circ}C$. As Sm$_2$O$_3$ content is increased, the breakdown voltage was increased in the range of 348.9~521.8 V/mm for ceramics sintered at 130$0^{\circ}C$ and 8.5~381.3 V/mm for ceramics sintered at 135$0^{\circ}C$. On the whole, the increase of sintering temperature led to the low nonlinearity regardless of Sm$_2$O$_3$content. ZnO-Pr$_{6}$O$_{11}$-CoO-based ceramics doped with 1.0 mol% at each sintering temperature exhibited the most superior varistor properties, with the nonlinear exponent of 42.1 at 130$0^{\circ}C$, 36.8 at 135$0^{\circ}C$ and the leakage current of 9.2 $\mu$A at 130$0^{\circ}C$, 11.7 $\mu$A at 135$0^{\circ}C$.EX>.EX>.

• Bulletin of the Korean Chemical Society
• /
• v.27 no.11
• /
• pp.1839-1843
• /
• 2006

Hydrothermal reactions of $Ln(NO_3)_3{\cdot}5H_2O $ (Ln = Eu (1), Sm (2), Ho (3), Dy (4)) with 3,5-pyridinedicarboxylic acid (3,5-pdcH2) in the presence of 4,4'-bipyridine led to the formation of the 3-D Ln(III)-coordination polymers with a formula unit of $[Ln_2(3,5-pdc)_2(C_2O_4)(H_2O)_4]{\cdot}2H_2O$. These polymers contain a bridging oxalate ligand ($C_2O_4\;^2$). On the basis of GCMS study of the mother liquor remaining after the reaction, we proposed that the $C_2O_4\;^2$ formation proceeds in three steps: (1) Ln(III)-mediated decarboxylation of $3,5-pdcH_2$ to give $CO_2$, (2) the reduction of $CO_2$ to $CO_2\;^{\cdot}$ by the Ln(II) species, and (3) the reductive coupling of the two $CO_2\;^{\cdot}$ radicals to the oxalate ($C_2O_4\;^2$) ion. All polymers were structurally characterized by X-ray diffraction.

• Journal of the Korean Ceramic Society
• /
• v.47 no.5
• /
• pp.457-460
• /
• 2010

$SmCoO_3$ system was investigated for their application to themoelectric materials. All specimens showed p-type semiconducting behavior and their electrical conductivity ($\sigma$), Seebeck coefficient (S) and power factor were measured at high temperature. And the effect of dopant ions on their thermoelectrical properties were also investigated. $Fe^{3+}$ ion doped into $Co^{3+}$ site enhanced the Seebeck coefficient and decreased the electrical conductivity simultaneously. The maximum Seebeck coefficient value for 60% doping case reached to 780 ${\mu}V$/K at $240^{\circ}C$. However $Fe^{3+}$ doped system cause an negative effect on power factor value. In case of the pure phase, the maximum Seebeck coefficient value reached to 290 ${\mu}V$/K at $240^{\circ}C$ and the maximum electrical conductivity was obtained 748 1/(ohm$\times$cm) at $960^{\circ}C$. As a result, the maximum power factor was obtained $1.49\times10^{-4}$ W/$mK^2$ at $550^{\circ}C$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.2
• /
• pp.69-73
• /
• 2010

The microstructural change of the $Sm_{0.5}Sr_{0.5}CoO_3$ (SSC) electrode for a cathode material of solid oxdie fuel cells (SOFCs) deposited by the electrostatic spray deposition (ESD) technique was characterized. Samarium chloride hexahydrate $(SmCl_3{\cdot}6H_2O)$, strontium chloride hexahydrate $(SrCl_2{\cdot}gH_2O)$, cobalt nitrate hexahydrate $(Co(No_3)_2{\cdot}6H_2O)$ as starting materials and methyl alcohol as solvent were used to make precursor solution. The suitable porous SSC films for a cathode of SOFCs were deposited on Si substrate and it is observed that the microstructure was strongly dependent on processing parameters such as deposition time, substrate temperature, and applied voltage. Scanning Electron Microscope (SEM) and X-ray Diffractometer (XRD) measurement were used to investigate the microstructure and crystallinity of the SSC films. The ESD technique is shown to be an efficient method in which the SOFCs' cathode film can be fabricated with the desired phases and microstructure.

• Journal of the Korean Ceramic Society
• /
• v.53 no.5
• /
• pp.500-505
• /
• 2016

Scandia-stabilized zirconia co-doped with $CeO_2$ is a promising electrolyte for intermediate temperature SOFC, but still shows rapid degradation during a long-term operation. In this study, $CeO_2$ (1 mol%) as a stabilizer is partially substituted with lanthanum oxides ($M_2O_3$, M=Yb, Gd, Sm) to stabilize a cubic phase and thus durability in reducing atmosphere. 0.5M0.5Ce10ScSZ electrolytes were prepared by solid state reaction and sintered at $1450^{\circ}C$ for 10 h to produce dense ceramic specimens. With addition of the lanthanum oxide, 0.5M0.5Ce10ScSZ showed lower degradation rates than 1Ce10ScSZ. Since $Gd_2O_3$ showed the highest ionic conductivity among the co-dopants, an electrolyte-supported cell with 0.5Gd0.5Ce10ScSZ was prepared to compare its long-term performance with that of 1Ce10ScSZ-based cell. Maximum power density of 0.5Gd0.5Ce10ScSZ-based cell was degraded by about 2.3% after 250 h, which was much lower than 1Ce10ScSZ-based cell (4.2%).