• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.2 no.2
• /
• pp.57-62
• /
• 2009

In this paper, we proposed the metal tag antenna of PIFA structure with an isotropic radiation pattern when tag attached the metal material. The antenna consist of antenna body, horizontal patch and ground, and inserted a substrate with high dielectric constant between the antenna body and ground in order to miniaturize the antenna size. The antenna body with symmetric structure is designed to produce an oppositely directed currents. The simulation shows the impedance bandwidth has 20 MHz (900 ~ 920 MHz) and the maximum radiation gain satisfy the -10 dBi and -15 dBi when the tag is in air and attach the metal material. Also, the proposed antenna operates with an isotropic radiation pattern due to satisfy the gain deviation lower than 6 dB, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.8
• /
• pp.1925-1930
• /
• 2014

This paper has analyzed the relation of conduction path and subthreshold swing for doping profile in channel of asymmetric double gate(DG) MOSFET. Since the channel size of asymmetric DGMOSFET is greatly small and number of impurity is few, the high doping channel is analyzed. The analytical potential distribution is derived from Possion's equation, and Gaussian distribution function is used as doping profile. The conduction path and subthreshold swing are derived from this analytical potential distribution, and those are investigated for variables of doping profile, projected range and standard projected deviation, according to the change of channel length and thickness. As a result, subthreshold swing is reduced when conduction path is approaching to top gate, and that is increased with a decrease of channel length and a increase of channel thickness due to short channel effects.

• Journal of the Institute of Convergence Signal Processing
• /
• v.7 no.2
• /
• pp.81-86
• /
• 2006

In this paper, a new process detection circuit is proposed. The proposed process detection circuit compares a long channel MOS transistor (L > 0.4um) to a short channel MOS transistor which uses lowest feature size of the process. The circuit generates the differential current proportional to the deviation of carrier mobilities according to the process variation. This method keep the two transistor's drain voltage same by implementing the feedback using a high gain OPAMP. This paper also shows the new design of the simple high gam self-biased rail-to-rail OPAMP using a proposed self-biased super MOS composite circuit. The gain of designed OPAMP is measured over 100dB with $0.2{\sim}1.6V$ wide range CMR in single stage. Finally, the proposed process detection circuit is applied to a differential VCO and the VCO showed that the proposed process detection circuit compensates the process corners successfully and ensures the wide rage operation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.336-337
• /
• 2005

ZnO varistor ceramics were fabricated as a function of the amount of $Y_2O_3$ addition and sintered at $1250^{\circ}C$ for 2 hour. The average grain size was decreased from 14.2 ${\mu}m$ to 8.3 ${\mu}m$ with the amount of $Y_2O_3$ addition, and varistor voltage was increased from 433 V to 563 V with $Y_2O_3$ addition. Nonlinear coefficient a of all specimens were increased with the amount of $Y_2O_3$ more than 67, in case of $Y_2O_3$ 0.01wt% addition showed the excellent results of 87. And leakage current was less than $1{\mu}A$ at 82% of varistor voltage. The clamping voltage ratio of the specimens added 0.01wt% $Y_2O_3$ was 1.41 at 25A [8/20${\mu}s$]. At the specimen 0.01wt% $Y_2O_3$ addition. endurance of surge current and deviation of varistor voltage were 5700A/$cm^2$ and $\Delta$-2.86%, respectively.

• Korean Journal of Materials Research
• /
• v.15 no.1
• /
• pp.25-30
• /
• 2005

The microstructural changes by hot extrusion of AZ31B magnesium alloy were observed, and the relation to the tensile property was examined. The tensile properties as oriented longitudinal(L), half transverse(HT) and long transverse(LT) to the extrusion direction were investigated at $20^{\circ}C,\;100^{\circ}C,\;200^{\circ}C,\;300^{\circ}C\;and\;400^{\circ}C$, respectively. As the results, many recrystallized small grains distributed uniformly in large banded microstructures formed along the extrusion direction. The grain size of as-extruded specimen was around $30\~150\;{\mu}m$. As increasing the test temperature the tensile and yield strength with respect to the angle between the axis of the tensile and the longitudinal direction in extrusion was decreased, but their elongation were increased and their deviation between L and LT specimens have disappeared from $300^{\circ}C$. This mechanical anisotropy was reduced at elevated temperatures and almost disappeared at $400^{\circ}C$. It was considered that the homogenization was occured by the recrystallization and the change of slip system was occurred during tensile test process in elevated temperatures.

• Journal of KIISE:Computer Systems and Theory
• /
• v.28 no.11
• /
• pp.549-560
• /
• 2001

Cluster system provides attractive scalability in terms of compution power and memory size. With the advances in high speed computer network technology, cluster systems are becoming increasingly competitive compared to expensive MPPs (massively parallel processors). Load balancing is very important issue since an inappropriate scheduling of tasks cannot exploit the true potential of the system and can offset the gain from parallelization. In parallel processing program, it is difficult to predict the load of each task before running the program. Furthermore, tasks are interdependent each other in many ways. The dynamic load balancing algorithm, which evaluates each processor's load in runtime, partitions each task into the appropriate granularity and assigns them to processors in proportion to their performance in cluster systems. However, if the communication cost between processing nodes is expensive, it is not efficient for all nodes to attend load balancing process. In this paper, we restrict a processor that attend load balancing by the communication cost and the deviation of its load from the average. We simulate various models of the cluster system with parameters such as communication cost, node number, and range of workload value to compare existing load balancing methods with the proposed dynamic algorithms.

• Journal of Radiation Industry
• /
• v.7 no.2_3
• /
• pp.115-119
• /
• 2013

The density profile measurement technology by gamma transmission has been widely used to diagnose processes in the field of refinery and petrochemical industry. This technology can reveal a clue and position of abnormal phenomenon of industrial processes during their operation. In this paper, the feasibility of the gamma transmission technology for detecting changes in the amount of fluid in a distillation column was evaluated by using Monte Carlo simulations. The simulations assumed that $^{60}Co$ (1.17, 1.33 MeV) sources and NaI (Tl) detectors (${\Phi}5{\times}5cm$) are located in opposite sides of a column and it concurrently moves in vertical direction. To determine the dependency of a spatial resolution on aperture size of a collimator, the simulation model for a tray in a column were simulated with the aperture sizes of 1 and 2 cm. The thickness of the high density area including a tray and fluid was 7.6 cm in the simulation. The spatial resolution of the tray was 8.2 and 8.5 cm, respectively. As a result, it was revealed that the conventional density profile measurement technique is not able to show the deviation of liquid level on a tray in a column.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.5
• /
• pp.709-718
• /
• 2010

This paper deals with two contents: first, distributions of plate slenderness ratios, stiffened plate slenderness ratios, and stiffener slenderness ratios, which include dimensions and material variables of stiffened plates, of stiffened plates of large-sized in-service vessels, and, second, comparison of compressive strengths. The investigated vessels consist of 59 tankers, 49 bulkers, 28 product carriers, 15 container carriers, and 12 multi-purpose vessels. The tankers are ranged from handymax class to VLCC and larger than Suezmax class. The sizes of the bulkers are 20K to 200K deadweight. The maximum size of containers is less than 5000TEU class. Two parameters for normal distributions of the slenderness ratios (mean and standard deviation) are suggested and probable ranges of the slenderness ratios are also graphically presented. The ultimate strengths of the stiffened plates are presented using the various simplified formulas and nonlinear FEAs. As well, average compressive strength curves, which are necessary for the estimation of the hull girder moment capacities, are proposed. It is proved that formulas for stiffened plates in CSR overestimate slightly in overall average strain range. Mode5 formula (plate buckling mode) in CSR show unreasonably conservative results with respect to the ultimate strengths rather than post-ultimate average compressive strengths.

• Animal cells and systems
• /
• v.14 no.3
• /
• pp.169-174
• /
• 2010

Cutlassfish (Trichiurus lepturus Linnaeus 1758) is a commercially important fish in Korea. In recent years, the catch of cutlassfish in the coastal waters of Korea has significantly declined. Its genetic characterization has been little studied. To assist conservation and management efforts, we isolated and characterized 10 microsatellite loci using an enrichment method based on magnetic/biotin capture of microsatellite sequences from a size-selected genomic library. To characterize each locus, 30 individuals from a natural T. lepturus population in the coastal waters of Jeju Island, Korea, were genotyped. All loci except two, KTh9B and KTh22A, were polymorphic, with an average of 14.3 alleles per locus (range, 10 22). The mean observed and expected heterozygosities were 0.80 (range, 0.50 0.97) a 0.82 (range, 0.68 0.95), respectively. A significant deviation from Hardy-Weinberg equilibrium was observed at three loci (KTh6B, KTh10, and KTh16). This high variability indicates that these microsatellites may be useful for high-resolution studies of population genetics.

• Korean Journal of Materials Research
• /
• v.31 no.9
• /
• pp.532-538
• /
• 2021

In this study, a spray dryer is used to make granules of Y₂O₃ and YF₃, and then Y₅O₄F₇ is synthesized following heat treatment of them under Ar gas atmosphere at 600 ℃. Single and binary monomer mixtures are compared and analyzed to optimize photocurable monomer system for DLP 3D printing. The mixture of HEA and TMPTA at 8:2 ratio exhibits the highest photocuring properties and low viscosity with shear thinning behavior. The optimized photocurable monomer and synthesized Y₅O₄F₇ are therefore mixed and applied to printing process at variable solid contents (60, 70, 80, & 85 wt.%) and light exposure times. Under optimal light exposure conditions (initial exposure time: 1.2 s, basic exposure time: 5 s), YOF composites at 60, 70 & 80 wt.% solid contents are successfully printed. As a result of measuring the size of the printed samples compared to the dimensions of the designed bar type specimen, the deviation is found to increase as the YOF solid content increases. This shows that it is necessary to maximize the photocuring activity of the monomer system and to optimize the exposure time when printing using a high-solids ceramic slurry.