• 전기의세계
• /
• v.24 no.4
• /
• pp.80-82
• /
• 1975

This paper presents a synthesis procedure of multi-channel active filters, which realizes an arbitrary N*N matrix of real rational functions in the complex variable s as a voltage transfer matrix. The resultant network reveals a transformerless grounded active RC(2N+1)-terminal network. The active network is consisted of six 2N-port RC networks with 2N single-ended operational amplifiers.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.1
• /
• pp.138-145
• /
• 1995

The offset voltage in silicon Hall plates is mainly caused by stress and strain in package, and by alignment in process. The offset voltage is appeared random for condition change with time in the factory, is non-linearly changed with temperature. In this paper proposed new method of design of Hall IC, and methematicaly proved relation layout of chip of 90$^{\circ}$-shift-current Hall plate pair is matched with "Differentail to single ended Conversion amplifier." In the experiment, the offset voltage is reduced about 1/100 time than the original offset voltage.

• Proceedings of the IEEK Conference
• /
• 2001.06e
• /
• pp.107-110
• /
• 2001

The capacitive idling SEPIC(Single Ended primary Inductance Converter) is derived from the SEPIC topology. This converter is suitable for maximizing Li-Ion battery life in portable equipments. Besides, that makes it possible to increase the switching frequency without a additional circuitry This paper is presented the characteristics of the capacitive idling SEPIC and experimental waveforms of the devices in continuous current mode.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.166-167
• /
• 2007

본 논문은 고주파 IH(Induction Heating) 조리기기의 전원으로 사용되는 인버터를 PI 제어기를 사용하여 듀티비를 가변시켜 출력을 최적 제어하는 회로를 제시하였다. 분석에 사용된 기본 인버터 회로는 Single-Ended Push-Pull (SEPP) 영전류 스위칭 공진인버터이며 실제 IH 조리기기의 동작을 구현하기 위해 입력단의 전원으로 220V 60Hz 정현파와 브리지 정류기, 평활 콘덴서를 사용하였다. 회로의 해석과 시뮬레이션을 위해 범용 시뮬레이션 툴인 Pspice를 이용하여 분석하였다. 향후, 제안된 제어방법은 유사한 IH 기기, DC-DC 컨버터, 인덕션 모터등의 시스템에 활용되리라 기대된다.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.05a
• /
• pp.39-42
• /
• 2009

본 논문에서는 콤팩트 세라믹 메탈핼라이드 램프용 가로등 기구의 반사판에 대해 2차원 설계법을 기반으로 한 3차원 설계로 150W single-ended type 콤팩트 세라믹 메탈핼라이드 램프 전용의 가로등용 반사판을 설계하였다.

• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.309-318
• /
• 2015

This study proposes a dual-output single-stage bridgeless single-ended primary-inductor converter (DOSSBS) that can completely remove the front-end full-bridge alternating current-direct current rectifier to accomplish power factor correction for universal line input. Without the need for bridge diodes, the proposed converter has the advantages of low component count and simple structure, and can thus significantly reduce power loss. DOSSBS has two uncommon output ports to provide different voltage levels to loads, instead of using two separate power factor correctors or multi-stage configurations in a single stage. Therefore, this proposed converter is cost-effective and compact. A magnetically coupled inductor is introduced in DOSSBS to replace two separate inductors to decrease volume and cost. Energy stored in the leakage inductance of the coupled inductor can be completely recycled. In each line cycle, the two active switches in DOSSBS are operated in either high-frequency pulse-width modulation pattern or low-frequency rectifying mode for switching loss reduction. A prototype for dealing with an $85-265V_{rms}$ universal line is designed, analyzed, and built. Practical measurements demonstrate the feasibility and functionality of the proposed converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.2
• /
• pp.126-133
• /
• 2022

This study proposes a suppression of zero sequence current (ZSC), which is caused by zero sequence voltage (ZSV) for a dual two-level inverter with single DC bus. Large output voltages enable the dual inverter with single DC bus to improve a system efficiency compared with single inverter. However, the structure of dual inverter with single DC bus inevitably generates ZSC, which reduces the system efficiency and causes a current ripple. ZSV is also produced by dead time, and its magnitude is determined by the DC bus and current direction. This study presents a novel space vector modulation method that allows the instantaneous suppression of ZSC. Based on a condition where a switching period is twice a sampling (control) period, the proposed control method is implemented by injecting the offset voltage at the primary inverter. This offset voltage is injected in half of the switching period to suppress the ZSC. Simulation and experiments are used to compare the proposed and conventional methods to determine the ZSC suppression performance.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2000.11a
• /
• pp.225-230
• /
• 2000

This paper describes a double-ended current fed push-pull type high frequency resonant inverter used as the power supply for wax-sealing. The proposed inverter can realize ZVS operation by using resonant capacitor to ZVS capacitor and has some merits not only reduction of switch current distribution but also extension of load range compare to the conventional single-ended current fed push-pull type high frequency resonant inverter. This analysis of proposed circuit uses normalized parameter ad characteristic estimation which is needed in each step before design is generally described according to normalized frequency($\mu$), normalized resistance(λ) and parameters. It is also presented as an example of method of the circuit design based on estimation analysis values from theoretical analysis. The theoretical analysis is proved through experiment and this circuit shows that it can be used practically as the power supply system for wax-sealing and DC-DC converter.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.12
• /
• pp.5984-5989
• /
• 2011

The buckling strength of a pin-ended column may be increased significantly by reinforcing it with an assemblage of cross-arm members rigidly connected to the modpoint of the column and stayed members connecting the ends of the columns and cross-arm members. The purpose of the stays and cross-arm members is to introduce restraint against translation and rotation and thereby decrease the effective buckling length of the column. In this study, buckling strengths of the reinforced columns were quantitatively evaluated from analytical solutions and elastic/inelastic finite elements analysis and the results were compared each other. It was found that the reinforcing system may increase the buckling strength up to 8 times compared to ones without reinforcing system.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.668-672
• /
• 2001

The utility interactive sinewave modulated inverter for the solar photovoltaic (PV) power conversion and conditioning with a new high frequency pulse modulated link is presented for domestic residential applications. As compared with the conventional full-bridge hard switching PWM inverter with a high frequency AC link, the simplest single-ended quasi-resonant soft switching sinewave modulated inverter with a duty cycle pulse control is implemented, resulting in size and weight reduction and low-cost. This paper presents a prototype circuit of the single-ended zero voltage soft switching sinewave inverter for solar power conditioner and its operating principle. In addition, this paper proposes a control system to deliver high quality output current. Major design of each component and the power loss analysis under actual power processing is also discussed from an experimental point of view. A newly developed interactive sinewave power processor which has $92.5\%$ efficiencty at 4kW output is demonstrated. It is designed 540mm-300mm-125mm in size, and 20kg in weight.