• Journal of The Korean Association For Science Education
• /
• v.25 no.5
• /
• pp.583-594
• /
• 2005

This study examined 8th-graders' conceptions of force on a simple pendulum and investigated cognitive conflict and conceptual change through kinesthetic experience in swing. Participants of this study were guided to anticipate the direction of total force acting on a pendulum at three critical positions and observed it through swing experience. Having completed this, students read an article explaining the results they observed. Most of them considered gravity, tension, and motion-force to be the real forces acting on a pendulum in pre-test. Though they were interested in the activity and conceded their expectations to be different from observed results, the degrees of their cognitive conflict were not significantly high. In summation, 'interest' was the highest and 'anxiety' was the lowest. Most of the students memorized the direction of forces on a swing, but few could explain the reason behind the occurrence in an immediate post-test and delayed post-test.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.5
• /
• pp.537-542
• /
• 2014

This paper proposes a control system to keep the balance of a unicycle robot. The robot consists of the disk and wheel, for balancing and driving respectively, and the tile angle is measured and used for balancing by the IMU sensor. A PID controller is designed based on a non-model based algorithm to prove that it is possible to control the unicycle robot without any approximated linear system model such as the sliding mode control algorithm. The PID controller has the advantage that it is simple to design the controller and it does not require an unnecessary complex formula. In this paper, assuming that the pitch and roll axis are dynamically decoupled, each of the two controllers are designed separately. A reaction wheel pendulum method is used for the control of the roll axis, that is, for balancing and an inverted pendulum concept is used for the control of the pitch axis. To confirm the performance of the proposed controllers using MATLAB Simulink, the dynamic equations of the robot are derived.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2016.05a
• /
• pp.106-107
• /
• 2016

Rolling motion of floating body might upset the body, make crews and passengers exhausted and/or apply forces to the structure to cause damage. Therefore for almost ships bilge keels are equipped, in special case fin stabilizer or gyroscope may be installed. This paper suggests the Anti-rolling pendulum to reduce roll motion to act the similar role with anti-rolling tank. The device suggested has more effective than the anti-rolling tank with 1/6 volume of the tank.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2116-2119
• /
• 2005

Inverted pendulum is a classical example and a famous tool for testing the effectiveness of many control schemes. Owing to their nonlinearity and unstable characteristic, a controller development either for swinging-up or stabilizing its upright position had been a great interest of many researchers. In this paper, the swinging-up control of the inverted pendulum using energy control will be presented. However, the saturation function in its control law could harm the experimental equipments. In addition, this swinging-up method did not consider limited sector of the arm angle to avoid another hazard, for instance, the twisted cable in the apparatus. Therefore, in this paper the position control of the arm angle using simple PD control in accordance with the energy control is proposed. Consequently, the limited arm sector angle can be achieved and the saturation function can also be replaced effectively by the PD control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.4
• /
• pp.436-442
• /
• 2016

This paper presents the torsional vibration isolation performance evaluation of a centrifugal pendulum absorbers (CPAs) that has a continuously varying resonance frequencies proportional to engine firing (excitation) order. CPAs are commonly used to suppress torsional vibrations in rotating machinery and internal combustion engines. In this study, they are employed on the current spring type torsional damper inside a torque converter of automotive vehicle. To evaluate the effectiveness of designed resonance tuning order, the torsional vibration transmissibility based on torque measurements with respect to different engine firing orders is experimentally measured with a lower-inertia dynamometer. The torsional vibration transmissibility with respect to different frequencies with engine order of 2 is also evaluated. It has been demonstrated that the significant vibration reduction over operational frequency range of interest can be achieved by attaching simple pendulums. Future research direction includes the study on theoretical analysis, improved design of pendulum etc.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.876-881
• /
• 2008

When biped robots speed up to run and reduce speed to walk after running, it needs stable speed translation. This paper proposed simple speed translation using the modified LIPM (Linear Inverted Pendulum Mode). We can change stride and period time of a biped robot in some bounded sets with this propose algorithm. This method is simple and effective in simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 1988.10b
• /
• pp.848-851
• /
• 1988

A simple procedure is proposed for the design of VSS controller to stabilize the single inverted pendulum. The controller is implemented by using a 16 bits personal computer.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.12 no.4
• /
• pp.55-61
• /
• 2008

One of the most recent base-isolation systems to improve the earthquake resistance of structures is the Friction Pendulum System(FPS). Simple in design but with versatile properties, the FPS has been used in some of the world s largest seismically isolated buildings, bridges and chemical tanks. FPS using PTFE(Polytetrafl-uoroethylene) based material has been developed to provide a simple and effective way for structures to achieve earthquake resistance. PTFE materials are soft, and are apt to become deformed easily after a few working cycles. In this study, magnetic force is used rather than the usual PTFE materials to improve the material shortcomings. A MF-FPS(Magnetic force-Friction Pendulum System) is proposed, and us shown to effectively protect structures against earthquakes. To demonstrate the advantages of this new system, the MF-FPS is compared with FPS as an attempt to prove its performance. A six-degree-of-freedom model is considered as a numerical example. The ground acceleration data of El Centro, Mexico and Gebze earthquakes are used as seismic excitations. The results showed that MF-FPS improved performance compared with FPS.

• Journal of Institute of Control, Robotics and Systems
• /
• v.12 no.4
• /
• pp.346-352
• /
• 2006

In a networked control system (NCS), time delays which are larger than one sampling period can change the control period. As a result, it may cause system instability. This paper presents a control method for an NCS using the controller area network (CAN), where time delays arise in the control loop. Specifically, a simple yet efficient method is proposed to improve control performance in the presence of time delays. The proposed method, which can be regarded as a gain scheduling method, selects a suitable LQ control gain among several gains to deal with the problems due to the change of control period. It is found that the gain can be scheduled in terms of the relation between the gain and the sampling period, which is represented by first-order algebraic equations. The proposed method is evaluated with an inverted cart pendulum system where the actuator and sensors are connected through the CAN. Experiment results are presented to show the efficiency of the proposed method.

• Earthquakes and Structures
• /
• v.13 no.1
• /
• pp.51-58
• /
• 2017

Passive dynamic vibration absorbers (DVAs) are often used to suppress the excessive vibration of a large structure due to their simple construction and low maintenance cost compared to other vibration control techniques. A new type of passive DVA consists of two pendulums connected with spring and dashpot element is investigated. This research evaluated the performance of the DVA in reducing the vibration response of a two degree of freedom shear structure. A model for the two DOF vibration system with the absorber is developed. The nominal absorber parameters are calculated using a Genetic Algorithm(GA) procedure. A parametric study is performed to evaluate the effect of each absorber parameter on performance. The simulation results show that the optimum condition for the absorber frequencies and damping ratios is mainly affected by pendulum length, mass, and the damping coefficient of the pendulum's hinge joint. An experimental model validates the theoretical results. The simulation and experimental results show that the proposed technique is able be used as an effective alternative solution for reducing the vibration response of a multi degree of freedom vibration system.