• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.9
• /
• pp.677-680
• /
• 2012

The dependency of annealing temperature on the electrical performances in amorphous silicon-zinc-tin-oxide thin film transistors (SZTO-TFT) has been investigated. The SZTO channel layers were prepared by using radio frequency (RF) magnetron sputtering method with different annealing treatment. The field effect mobility (${\mu}_{FE}$) increased and threshold voltage ($V_{th}$) shifted to negative direction with increasing annealing temperature. As a result, oxygen vacancies generated in SZTO channel layer with increasing annealing temperature resulted in negative shift in $V_{th}$ and increase in on-current.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.1
• /
• pp.200-205
• /
• 1995

The 1st and 2nd-order grating structure for long wavelength DFB(Distributed FeedBack) laser diodes are successfully fabricated on InP substrates by using electron beam lithography and reactive ion etch techniques, and also characterized non-destructively by diffraction analysis without removal of photo-resis layer. A new composite layer made by lifted-off Cr layer on thin SiO2 film is developed and used as an etch mask, because PMMA, the e-beamresist, is unsuitable for reactive ion etch of InP. In addition, it is experimentally confiremed that diffraction analysis makes it possible to predict the grating parameters, and the analysis can be used as a non-destructive on-line test to prevent incomplete gratings from being successively processed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.45-46
• /
• 2005

The piezoelectric ZnO thin films were deposited onto Al/Si substrate in order to figure out the crystalline and the residual stress of deposited films. As the $Ar/O_2$ gas ratio is increased, c-axis orientation of deposited films is significantly enhanced and also the residual stresses of ZnO films are all compressive. They are decreased from -1.2 GPa to -950 MPa as the $Ar/O_2$ gas ratio is increased. A diaphragm-based piezoelectric microspeaker fabricated on ONO films shows about 14 mPa output pressure at 1 kHz with $8V_{peak-to-peak}$.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2017.07a
• /
• pp.131-132
• /
• 2017

본 연구에서는 열처리 온도에 따른 전도 특성을 조사하기 위하여 RF magnetron sputtering을 이용해서 Si기판 위에 SBN 박막을 증착시킨 후, SBN 박막에 $650{\sim}800[^{\circ}C]$의 온도 범위에서 열처리를 하였다. $650[^{\circ}C]$에서 열처리된 박막의 경우 표면 거칠기는 약 0.42[nm]로 나타났으며, -5~+5[V]의 전압 범위에서 누설전류밀도는 $10-5[A/cm^2]$ 이하로 안정된 값을 나타내었다.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2002.10a
• /
• pp.32.2-32
• /
• 2002

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.47-47
• /
• 2007

Indium oxide conducting films were dep9sited on Si(100) substrates at various temperatures by liquid delivery metal organic chemical vapor deposition using Indium (III) tris (2,2,6,6-tetramethyl-3.5-heptanedionato) $(dpm)_3$ precursors. The films deposited at $200{\sim}400^{\circ}C$ were grown with a (111) preferred orientation and exhibit an increase of grain size from 21 to 33nm with increasing deposition temperature. In the range of deposition temperature, there is no metallic indium phase in deposited films.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.2
• /
• pp.70-73
• /
• 2017

We investigated n-i-p type single junction hydrogenated amorphous silicon oxide solar cells. These cells were without front surface texture or back reflector. Maximum power point efficiency of these cells showed that an optimized device structure is needed to get the best device output. This depends on the thickness and defect density ($N_d$) of the active layer. A typical 10% photovoltaic device conversion efficiency was obtained with a $N_d=8.86{\times}10^{15}cm^{-3}$ defect density and 630 nm active layer thickness. Our investigation suggests a correlation between defect density and active layer thickness to device efficiency. We found that amorphous silicon solar cell efficiency can be improved to well above 10%.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1404_1405
• /
• 2009

For quantitative understanding of gas discharge phenomena, we should know electron collision cross section. $GeH_4$ is used in many applications with $Si_2H_6$ gas, such as amorphous alloy, a thin film of silicon and solar cell. Therefore, we understand the electron transport characteristics and analysed the electron transport coefficients, the electron drift velocity W, the longitudinal and transverse diffusion coefficient $ND_L$ and $ND_T$, and the ionization coefficient $\alpha$/N in $GeH_4$gas over the E/N range from 0.01 to 1000 Td by two-term approximation of the Boltzmann equation.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.80-82
• /
• 2009

The dependence of the efficiency characteristics of hydrogenated amorphous silicon single junction solar cells on the various intrinsic layer thickness has been investigate in the glass/$SnO_2$:F/p,i,n a-Si:H/Al type of amorphous silicon solar cells by cluster PECVD system. The open circuit voltage, short circuit current, fill factor and conversion efficiency have been measured under AM 1.5 condition. The result of the cell performance was improved about 8.2% due to an increase in the short circuit current.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.4 s.33
• /
• pp.49-53
• /
• 2004

Polymeric materials are widely used in the electronic industry as a common dielectric material or adhesive. The polymeric layer coated on Si substrate can be subjected to thermal stresses due to difference in thermal expansion coefficients. The mismatch in thermal properties between the polymeric layer and the substrate results in significant residual stresses. In this study, the thermal deformation is measured by a curvature measurement method using laser scanning, and the elastic modulus is calculated by an analytic model.