• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.584-591
• /
• 2013

In this paper, a hybrid booster power module with Si IGBT and Silicon Carbide (SiC) Schottky Barrier Diode (SBDs) is presented. The switching characteristics of the hybrid booster module are compared with commercial Silicon IGBT/Si PIN diode based modules. We applied the booster power module into a non-isolated on board vehicle charger with a simple buck-booster topology. The performances of the on-vehicle charger are analyzed and measured with different power modules. The test data is measured in the same system, at the same points of operation, using the conventional Si and hybrid Si/SiC power modules. The measured power conversion efficiency of the proposed on-vehicle charger is 96.4 % with the SiC SBD based hybrid booster module. The conversion efficiency gain of 1.4 % is realizable by replacing the Si-based booster module with the Si IGBT/SiC SBD hybrid boost module in the 6.6 kW on-vehicle chargers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.232-233
• /
• 2008

The 4H-SiC schottky diodes treated by the various dry etch methods were fabricated and electrically characterized. The post etch process including an Inductively Coupled Plasma(ICP) etch and a Neutron Beam Etch(NBE) was performed after a high-temperature activation annealing without graphite cap in order to eliminate the damaged surface generated during the activation annealing. The reverse leakage current of diode treated by ICP was 1/35 times lower than that of the diode without any post etch at the anode bias of -100V, while the reverse leakage current of diode treated by NBE was 1/44 times lower at the same bias.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.4
• /
• pp.199-202
• /
• 2017

Silicon carbide (SiC) is being spotlighted as a next-generation power semiconductor material owing to the characteristic limitations of the existing silicon materials. SiC has a wider band gap, higher breakdown voltage, higher thermal conductivity, and higher saturation electron mobility than those of Si. When using this material to implement Schottky barrier diode (SBD) devices, SBD-state operation loss and switching loss can be greatly reduced as compared to that of traditional Si. However, actual SiC SBDs exhibit a lower dielectric breakdown voltage than the theoretical breakdown voltage that causes the electric field concentration, a phenomenon that occurs on the edge of the contact surface as in conventional power semiconductor devices. Therefore in order to obtain a high breakdown voltage, it is necessary to distribute the electric field concentration using the edge termination structure. In this paper, we designed an edge termination structure using a field plate structure through oxide etch angle control, and optimized the structure to obtain a high breakdown voltage. We designed the edge termination structure for a 650 V breakdown voltage using Sentaurus Workbench provided by IDEC. We conducted field plate experiments. under the following conditions: $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, and $75^{\circ}$. The experimental results indicated that the oxide etch angle was $45^{\circ}$ when the breakdown voltage characteristics of the SiC SBD were optimized and a breakdown voltage of 681 V was obtained.

• Korean Journal of Materials Research
• /
• v.8 no.9
• /
• pp.825-830
• /
• 1998

자화된 유도결합형 C4F8 플라즈마로 SiO2를 건식식각시 실리콘 표면에 발생하는 손상과 오염에 대하여 연구하였다. 오염의 분석을 위해서 XPS, SIMS, TEM을 사용하였으며, 손상정도를 측정하기 위해서 HRTEM과 Schottky-diode 구성을 통한 I-V특성 측정을 사용하였다. 유도 결합형 C4F8 플라스마에 0에서 18Gauss까지의 자장이 가해짐에 따라서 실리콘 표면에 생기는 잔류막의 두께가 SiO2식각속도와 선택비의 증가와 함께 증가하였으며, XPS를 통하여 그 조성이 fluorine-rich에서 carbon-rich 한 상태로 변화함을 알 수 있었다. 자장을 가하지 않는 상태에서는 표면에서 $40\AA$부근까지 고밀도의 손상층이 관찰되었으나, 자장을 가함에 따라서 노출된 손상층의 깊이는 깊어지나 그 밀도는 줄어들음을 HRTEM을 통하여 관찰 할 수 있었다. Schottky-diode를 통한 I-V특성곡선의 분석으로 자장이 증가함에 따라서 전기적인 손상이 감소함을 알 수 있었다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.8 no.4
• /
• pp.640-644
• /
• 1998

We have fabricated Sb/SiC(4H) Schottky barrier diode (SBD) of which characteristics compared with that of Ti/SiC(4H) SBD. The donor concentration of the n-type SiC(4H) obtained by capacitance-voltage (C-V) measurement was about $2.5{\times}10 ^{17}{\textrm}cm^{-3}$. The ideality factors of 1.31 was obtained from the slope of forward current-voltage (I-V) characteristics of Sb/SiC(4H) SBD at low current density. The breakdown field of Sb/SiC(4H) SBD under the reverse bias voltage was about $4.4{\times}10^2V$/cm. The built-in potential and the Schottky barrier height (SBH) of Sb/SiC(4H) SBD were 1.70V and 1.82V, respectively, which were determined by the analysis of C-V characteristics. The Sb/SiC(4H) SBH of 1.82V was higher than Ti/SiC(4H) SBH of 0.91V. However, the current density and reverse breakdown field of Sb/SiC(4H) were low as compared with those of Ti/SiC(4H). The Sb/SiC(4H), as well as the Ti/SiC(4H), can be utilized as the Shottky barrier contact for the high-power electronic device.

• Korean Journal of Materials Research
• /
• v.5 no.8
• /
• pp.1020-1025
• /
• 1995

The Schottky barrier hieght(SBH) of Au/n-Si(100) were investigated by current-voltage(I-V) and capacitance voltage(C-V) measurement within a temperature range of l00K∼300K. The values of SBH at room temperature obtained from these two measurements were (0.79${\pm}$0.02)eV. The SBH obtained from the C-V measurement was temperature independent, while that obtained from the I-V measurement decreased linearly with decreasing temperature. This indicates that the Schottky diode has deviated from the thermionic emission theory at low-temperature, Thus, other current transport processes were considered and the contribution of recombination current was dominant at low temperature. We found that it leads to a lower SBH value. Thus, the conflicating results between C-V and I-V measurement were explained, C-V measurement is believed to yield mare reliable SBH values in present study since it is not affected by the current transport uncertainties.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.4
• /
• pp.449-455
• /
• 2019

This paper proposes a flyback diode of bridgeless PFC converter as SiC SBD (Schottky Barrier Diode) to achieve high efficiency. In addition, through the explanation of the operation principle of the bridgeless PFC converter, the conduction section of the freewheel diode is shown in the bridgeless PFC converter to verify the contribution of system loss due to the loss of the freewheel diode. The advantages of the SiC SBD device's physical properties and the reverse recovery characteristics are explained, and the efficiency is measured by measuring the turn-on and turn-off losses. The loss was calculated. The simulation results were calculated in consideration of device characteristics and verified through the waveform analysis and comparison of the actual system. In order to consider the device characteristics, the simulation was conducted using the thermal module of PSIM. As a result of the prototype test, the turn-on loss was 0.608W and the turn-off loss was 21.62W, resulting in the total switching loss of 22.228W. The comparison of the two results proved the validity of the experimental method. In addition, a high efficiency of 94.58% is achieved.

• Journal of IKEEE
• /
• v.21 no.1
• /
• pp.73-76
• /
• 2017

SiC devices have drawn much attentions for its wide band gap material properties. Especially 4H-SiC Schottky barrier diode is widely used for its rapid switching speed and low forward voltage drop. However, the low reliability of Schottky barrier diode has many problems that Super Barrier Rectifier(SBR) was researched for alternative. makes 4H-SiC trench-type accumulation super barrier rectifier(TASBR) is analyzed and proposed in this paper. We could verified that forward voltage drop was improved 21.06% without severe degradation of reverse breakdown voltage and leakage current based on the results from 2-D numerical simulations. With this novel rectifier structure, we can expect application with less power loss.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.3
• /
• pp.487-493
• /
• 1997

Ti/sic(4H) Schottky barrier diodes were fabricated. The donor concentration and the built-in potential obtained by capacitance-voltage(C-V) measurement was about $2.0{\times}10^{15}{\textrm}{cm}^{-3}$ and 0.65 V, respectively. The ideality factor of 1.07 was obtained from the slope of current-voltage(I-V) characteristics at low current density. The breakdown field under the reverse bias voltage was about $1.7{\times}10^3V/{\textrm}{cm}$ and was very high. The barrier height of Ti for SiC(4H) was 0.91 V, which was determined by the analysis of the saturation current-temperature and the C-V characteristics.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.11
• /
• pp.908-913
• /
• 2000

CoSi$_2$/p+/n diodes(bilayer diodes) were fabricated by using epitaxial CoSi$_2$grown from Co/Ti bilayer as a diffusion source. The I-V characteristics of p+/n diodes were measured and compared with those of diode made from Co monolayer (monolayer diode). Monolayer diodes showed typical p+n junction characteristics with the leakage current of as low as 10$^{-12}$ A and forward current 6-orders higher than the leakage current, when drive-in annealed at 90$0^{\circ}C$ for 20 sec.. On the other hand, bilayer diodes showed the Schottky-like behaviors with forward currents rather higher than those of monolyer diodes, but with too high leakage currents, when drive-in annealed at $700^{\circ}C$ or higher. However, when the annealing temperature was lowered to $700^{\circ}C$ and annealing time was increased to 60 sec., the leakage current was reduced to 10$^{-11}$ A and thus sho3wed typical diode characteristics. The high leakage currents for diodes annealed at $700^{\circ}C$ or higher was attributed to Shannon contacts formed due to unremoved Co-Ti-Si precipitates. But when annealed at 50$0^{\circ}C$, B ions diffused in the direction of the surface layer, and thus the leakage currents were reduced by removing Shannon contacts.