• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.3
• /
• pp.192-197
• /
• 2017

Hydrogenated Amorphous Silicon (a-Si:H) is used as an emitter layer in HIT (heterojunction with Intrinsic Thin layer) solar cells. Its low band gap and low optical properties (low transmittance and high absorption) cause parasitic absorption on the front side of a solar cell that significantly reduces the solar cell blue response. To overcome this, research on CSC (carrier Selective Contacts) is being actively carried out to reduce carrier recombination and improve carrier transportation as a means to approach the theoretical efficiency of silicon solar cells. Among CSC materials, molybdenum oxide ($MoO_x$) is most commonly used for the hole transport layer (HTL) of a solar cell due to its high work function and wide band gap. This paper analyzes the electrical and optical properties of $MoO_x$ thin films for use in the HTL of HIT solar cells. The optical properties of $MoO_x$ show better performance than a-Si:H and ${\mu}c-SiO_x:H$.

• Laser Solutions
• /
• v.14 no.3
• /
• pp.1-6
• /
• 2011

Globally, the interest of renewable energy has become an upsurge. Especially, the solar industry is the one which is getting rapid growth rate. Many of researchers have been undertaking to improve the efficiency of solar cell to accomplish grid parity. The most of research has been concentrated on two methods, one on the selective emitter and the other is on LBSF (Local Back Surface Field) formation. Laser patterning will be needed to eliminate the thin film to form selective emitter and LBSF of solar cell. This paper reports some experimental results in laser patterning process for high-efficiency crystalline solar cell manufacturing. The experimental results indicate that the patterning quality depends on the average power and repetition rate of laser. The experimental results prove that the laser patterning process is an advantageous method to improve the efficiency of solar cell.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.05a
• /
• pp.52.2-52.2
• /
• 2009

Si 박막형 solar cell은 Si 결정형 solar cell대비 cost 및 대면적화 측면에서 장점을 가지고 있다. 그러나 amorphous Si의 경우 light soacking에 의한 열화 문제가 있고, microcrystalline Si의 경우 요구되는 효율 확보를 위하여 $1.5{\mu}m$ 이상 두께가 필요하며, 증착율이 $5{\AA}/sec$.이하인 단점이 있다. 본 연구에서는 high deposition rate로 microcrystalline Si를 증착하기 위하여 high frequency, high power PECVD를 이용하였으며, RF power, 증착온도, H2/SiH4 ratio의 3인자를 3수준으로 변화시킨 완전요인배치 실험을 실시하였다. 실험결과 증착율은 $8.0{\AA}/sec.{\sim}52.8{\AA}/sec$ 범위, crystalline fraction은 0%~83.3% 범위의 결과를 얻었으며, 결정이 형성된 조건에서는 XRD분석결과 $2\theta=28.5$ 및 47.5에서 Si (111), (220) peak을 확인할 수 있었다. Surface Profilometer 를 이용한 surface roughness의 경우 $6.3{\AA}\sim32.4{\AA}$ 범위의 결과를 얻었으며, crystalline Portion이 높을수록 surface roughness가 증가함을 알 수 있었다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1316-1317
• /
• 2011

This paper presents analysis of temperature and light intensity characteristics of PV modules with solar cell type. Taking the effect of sunlight irradiance on the cell temperature, the first experiment takes ambient temperature as reference input and uses the solar insolation as a unique varying parameter. Then taking the effect of the cell temperature on sunlight irradiance, the second experiment takes 1000W/$m^2$ as reference input and uses the cell temperature as a unique varying parameter. As a result, varying sunlight irradiance, the Cell-Type with the smallest change in output is HIT and the Cell-Type with the biggest change in output is a-Si. Varying the cell temperature, the Cell-Type with the smallest change in output is a-Si and the Cell-Type with the biggest change in output is Single-Si. And considering both temperature and light intensity characteristics, the Cell-Type with the smallest change in output is HIT.

• Proceedings of the KIEE Conference
• /
• 1990.07a
• /
• pp.183-186
• /
• 1990

The lattice mismatch between ZnS and Si is negligible because of its value being 0.39%. In this study, $ZnS/_{(P)}Si$ solar cell were fabricated as a layer of ZnS is epitaxially grown on a silicon substrate by PVD method and its photovoltaic properties were measured and discussed. The heat treatment was done after deposition. As the temperature increased up to a certain value, the film has better perfection in crystal structure and electrical characteristics. Measurments of the change that occur in the ZnS films were made by SEM., X-ray diffraction. The optimal thickness of film showned $0.6{\mu}m$, being measured by SEM. The great improvement of the grain growth ZnS film came out after heat-treatment. The result obtained from the $ZnS/_{(P)}Si$ solar cell as follows:short circuit current; $I_{sc}=54mA/cm^2$,open voltage; $V_{oc}=400mV$, fill factor FF=0.72, conversion efficiency; ${\eta}=15.6%$ under the irradiation of 100 ($mW/cm^2$) focused by solar energy. And these are discussed in comparison with other kinds.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.489-489
• /
• 2011

The effect of Si quantum dots for solar cell appications was investigated. The 5 ~ 10 nm Si nanoparticle was fabricated on p-type single and poly crystalline wafer by magnetron sputtering and laser irradiation process. Scanning electron microscopy (SEM), atomic force measurement (AFM) and transmission electron microscopy (TEM) images showed that the Si QDs array were clearly embedded in insulating layer ($SiO_2$). Photoluminesence (PL) measurements reliably exhibited bandgap transitions with every size of Si QDs. The photo-current measurements were showed different result with size of QD and number of superlattice.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.2
• /
• pp.39-43
• /
• 2017

It was confirmed that the silicon thin films fabricated on the p-Si (100) substrates by using DIPAS (DiIsoPropylAminoSilane) and TDMA-Sb (Tris-DiMethylAminoAntimony) sources by RPCVD method were amorphous and n-type silicon. The fabricated amorphous n-type silicon films had electron carrier concentrations and electron mobilities ranged from $6.83{\times}10^{18}cm^{-3}$ to $1.27{\times}10^{19}cm^{-3}$ and from 62 to $89cm^2/V{\cdot}s$, respectively. The ideality factor of the pn junction diode fabricated on the p-Si (100) substrate was about 1.19 and the efficiency of the fabricated pn solar cell was 10.87%.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.766-772
• /
• 2011

Amorphous Si (a-Si) thin films of $p^+/p^-/n^+$ were deposited on $Si_3N_4$/glass substrate by using a plasma enhanced chemical vapor deposition (PECVD) method. These films were annealed at various temperatures and for various times by using a rapid thermal process (RTP) equipment. This step was added before the main thermal treatment to make the nuclei in the a-Si thin film for reducing the process time of the crystallization. The main heat treatment for the crystallization was performed at the same condition of $600^{\circ}C$/18 h in conventional furnace. The open-circuit voltages ($V_{oc}$) were remained about 450 mV up to the nucleation condition of 16min in the nucleation RTP temperature of $680^{\circ}C$. It meat that the process time for the crystallization step could be reduced by adding the nucleation step without decreasing the electrical property of the thin film Si for the solar cell application.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.30 no.3
• /
• pp.139-143
• /
• 2017

N-type crystalline silicon solar cells have high metal impurity tolerance and higher minority carrier lifetime that increases conversion efficiency. However, junction quality between the boron diffused layer and the n-type substrate is more important for increased efficiency. In this paper, the current status and prospects for boron diffused layers in N-type crystalline silicon solar cell applications are described. Boron diffused layer formation methods (thermal diffusion and co-diffusion using $a-SiO_X:B$), boron rich layer (BRL) and boron silicate glass (BSG) reactions, and analysis of the effects to improve junction characteristics are discussed. In-situ oxidation is performed to remove the boron rich layer. The oxidation process after diffusion shows a lower B-O peak than before the Oxidation process was changed into $SiO_2$ phase by FTIR and BRL. The $a-SiO_X:B$ layer is deposited by PECVD using $SiH_4$, $B_2H_6$, $H_2$, $CO_2$ gases in N-type wafer and annealed by thermal tube furnace for performing the P+ layer. MCLT (minority carrier lifetime) is improved by increasing $SiH_4$ and $B_2H_6$. When $a-SiO_X:B$ is removed, the Si-O peak decreases and the B-H peak declines a little, but MCLT is improved by hydrogen passivated inactive boron atoms. In this paper, we focused on the boron emitter for N-type crystalline solar cells.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.4
• /
• pp.92-100
• /
• 1985

New N+N/P HLE solar cells with N+ surface charge accumulated layer in the emitter region are fabricated on the N/P Si epiwafer by incorporating high fixed positive charge density (Qss) at the Si-AR layer interface. Solar cells are classified into two categories, i.e, OCI and NCI Cell depending on AR layer, SiOl and Si3 N4/sioxynitride layer respectively. The distribution of Qss in the Si-AR layer interface is examined by C-V plot. It shows that the surface charge accumulated layer is formed more effectively in the NCI cell (Qss=1.79-1.84$\times$1012cm-2) than in the OCI cell (Qss=3.03~4.40$\times$1011 cm-2). The efficiency characteristics are evaluated under the JCR halogen lamp of 100 mw/cm2. The average (maximum) conversion efficiency for active area is 15.18 (15.46)% in the OCI cell and 16.31 (17.07)% in the NCI cell.