• 한국결정성장학회지
• /
• 제14권6호
• /
• pp.257-261
• /
• 2004

태백 도석은 주로 quartz와 함께 kaolinite가 포함되어 있다. 도석의 특성분석은 XRD, XRF, TG--DTA, SEM등을 이용하여 결정상과 화학성분 등을 분석하였다. 원석의 화학조성은 71.75wt%$SiO_2$, 22.10wt%$Al_2O_3$, 1.86wt%CaO, 2.97wt%$K_2O$, 0.62 wt%$Fe_2O_3$ 등이다. 3mm 크기의 도석을 $80^{\circ}C$의 10% 수산 농도에서 침출하면 탈철은 0.62wt%에서 0.24wt%로 감소하고 백색도가 증가하였다. 도석의 분쇄는 planetary ball mill을 이용하여 지르코니아 볼로 분쇄하였으며, 입도 크기는 25$\mu\textrm{m}$ 크기로 균일하게 분쇄되었다.

• 대한기계학회논문집A
• /
• 제27권5호
• /
• pp.840-847
• /
• 2003

The bonding of adhesive joints of adhesive joints is influenced by the surface roughness of the joining Parts. However, the magnitude of the influence has not yet been clarified because of the complexity of the phenomena. In this study, it is shown that surface treatment affects adhesive strength and durability of alumina/polycarbonate single-lap .joints, and leading speed affects tensile-shea strength of adhesive Joints. To evaluate effect of surface treatments on the adhesive strength, several surface treatment methods are used, that is, cleaning, grinding, SiC polishing and sand blasting. It is shown that an optimum value of the surface roughness exists with respect to the tensile-shea strength of adhesive joints. The adhesive strength shows linear relationship with the surface roughness and loading speed. And the mechanical removal of disturbing films of lubricants, impurities and oxides make adhesive strength increase significantly.

• Journal of Welding and Joining
• /
• 제31권3호
• /
• pp.84-88
• /
• 2013

These days embedded technology may be the most significant development in the electronics industry. The study focused on the development of active device embedding using flexible printed circuit in view of process and materials. The authors fabricated 30um thickness Si chip without any crack, chipping defects with a dicing before grinding process. In order to embed chips into flexible PCB, the chip pads on a chip are connected to bonding pad on flexible PCB using an ACF film. After packaging, all sample were tested by the O/S test and carried out the reliability test. All samples passed environmental reliability test. In the future, this technology will be applied to the wearable electronics and flexible display in the variety of electronics product.

• 동아시아식생활학회지
• /
• 제20권3호
• /
• pp.452-457
• /
• 2010

To obtain basic information on the utilization of Suaeda (S.) asparagoides $M_{IQ}$ as a raw material in food, it's chemical components of were investigated. S. asparagoides $M_{IQ}$ from the Hwaseong-si in Korea was used after drying and grinding with powder. The total dietary fiber, insoluble dietary fiber and soluble dietary fiber contents of S. asparagoides $M_{IQ}$ were found to be 39.41%, 37.63% and 1.78%, respectively. Macromineral components of S. asparagoides $M_{IQ}$ were Na (7.6%), K (2.4%) and Mg (0.6%). High contents of microminerals such as Cu, Mn and Zn were also found. Lysine and methionine which are essential amino acids were detected with the value of 215 mg/100 g and 23.2 mg/100 g, respectively. S. asparagoides $M_{IQ}$ that was harvested in May was higher in crude protein than that harvested in September but the crude fat content of that which was harvested in September was twice as high as that harvested in May.

• 한국재료학회지
• /
• 제19권12호
• /
• pp.661-666
• /
• 2009

Froth flotation has been carried out in order to produce roasting-molybdenite concentrate from molybdenite ore in the Shin-yeomi mine. In our study, roasting-molybdenite (Mo 0.43%) from Shin-yeomi mine was recovered by varying the conditions of regrinding time, dosage of collector and alkalinity. Liberation and flotation efficiency more were effective at regrinding time of six minutes than at single grinding. Mo recovery curves increased considerably as dosage of kerosene increased, whereas Mo grade curves decreased gradually. The separation efficiency of molybdenite was effective when the dosage of collector (kerosene) was adjusted to 300 g/t. The molybdenite concentrate was agglomerated in the range of pH 5-7 and its separation efficiency increased to pH 9-10. The concentrate of 49.5% Mo grade ($MoS_2$, 82.6%) with 81.5% recovery from Shin-yeomi molybdenite ores was obtained under conditions of 20% pulp concentration, 300 g/t kerosene 325 g/t frother (AF65), 2.5 kg/t depressant ($Na_2SiO_3$), pH 9-10 and four cleaning times. In the future, a trial run that can separate up to 50% Mo grade from Shin-yeomi molybdenite ores will be performed.

• 한국기계가공학회지
• /
• 제21권2호
• /
• pp.123-129
• /
• 2022

Quartz (SiO2) has high abrasion and heat resistances and excellent chemical and mechanical properties; therefore, it is used in various industries, such as machinery, chemistry, optics, and medicine. Quartz is a high-hardness and brittle material and is classified as the topmost difficult-to-cut material, which is because of the cracking or chipping at the edge during processing. Corner wear, such as cracks and chippings that occur during cutting, is a major cause for the deterioration in the machining quality. Therefore, many researchers are investigating various techniques to process quartz effectively. However, owing to the mechanical properties of quartz, most studies have been conducted on grinding, micromachining, and microdrilling. Few studies have been conducted on quartz processing. The purpose of this study was to analyze the machining characteristics according to the machining factors during the slot machining of quartz using a cubic boron nitride (CBN) tool and to select the optimal machining conditions using the Taguchi method. The machining experiment was performed considering three process variables: the spindle speed, feed rate, and depth of cut. The cutting force and surface roughness were analyzed according to the processing conditions.

• Corrosion Science and Technology
• /
• 제20권6호
• /
• pp.475-483
• /
• 2021

Additively manufactured titanium alloy is one of the promising materials in advanced medical industries. However, these additively manufactured alloys show corrosion properties different from those of conventional materials due to their unique microstructure. In this study, the effect of surface roughness and masking conditions on the results of the potentiodynamic polarization tests on additively manufactured or conventional Ti-6Al-4V alloys in artificial saliva solution with or without fluoride was investigated. The results showed that the corrosion potential was slightly lower with a flat cell with an O-ring than with masking tape. The corrosion rate was decreased with decreases in the surface roughness. Localized corrosion involving delamination of the surface layer occurred at 7 ~ 9 V (SSC) on the additively manufactured alloy in solution with or without fluoride when the samples were finished with 1000-grit SiC paper, whereas localized corrosion was not observed in the specimens finished with 1-㎛ alumina paste.

• 청정기술
• /
• 제28권3호
• /
• pp.203-209
• /
• 2022

본 연구에서는 태양광 폐모듈 해체과정에서 회수한 실리콘을 재활용하여 기계구조용 메커니컬 실을 제조하는 공정에 대해 전과정평가 방법에 의한 환경성평가를 수행하였다. 재활용 실리콘은 고순도 정제 후 탄소와 반응시켜 β-SiC 입자로 합성하고 압축 성형, 소결 및 열처리를 거쳐 제품을 생산한다. 현장 데이터 수집 및 환경부 LCI DB를 활용하여 각 단계별로 자원고갈, 산성화, 부영양화, 지구온난화, 오존층파괴, 광화학산화물 등 6개 영역의 환경영향을 산정하였다. 영향범주 별 환경영향은 지구온난화 45 kg CO₂, 광화학산화물 2.23 kg C₂H₄으로 크게 나타났으며 가중화 분석결과 광화학산화물, 자원고갈 및 지구온난화에 의한 환경영향이 98.7%로 높은 기여도를 차지하였다. 원료 실리콘과 탄소를 미분쇄 혼합하는 습식공정과 β-SiC 과립화 공정이 주요한 환경영향 유발요인이므로 건식공정으로 전환 및 대기 배출되는 용매는 회수하여 재이용하는 시스템으로 개선이 필요하다. 폐모듈 실리콘의 재활용에 의해 자원고갈의 영향은 53.9%, 지구온난화는 60.7% 감소하며 가중화 결과 전체적인 환경영향이 27% 감소하는 것으로 분석되어 폐모듈 재활용은 자원절약과 탄소중립 실현의 주요 수단이 될 수 있음을 LCA 분석으로 확인하였다.

• Restorative Dentistry and Endodontics
• /
• 제25권2호
• /
• pp.243-253
• /
• 2000

The purpose of this in vitro study was to evaluate dentin bonding by two different dentin bonding systems(DBS) using acetone based primer or adhesive [All Bond 2(AB2), One Step(OS)] when they were applied by wet or dry bonding technique. Morphology of resin-dentin interface and hybrid layer thickness(HLT) were investigated using Confocal Laser Scanning Microscope(CLSM) and compared to shear bond strength(SBS). 72 extracted sound human molars were randomly divided into 4 groups of 18 teeth each - Group 1.(AW); AB2 by wet bonding. Group 2(AD); AB2 by dry bonding. Group 3.(OW); OS by wet bonding, Group 4.(OD); OS by dry bonding. In 6 teeth of each group, notch-shaped class V cavities(depth 2mm) were prepared on buccal and lingual surface at the cementoenamel juction(12 cavities per group). To obtain color contrast in CLSM observation, bonding resins of each DBS were mixed with rhodamine B and primer of AB2 was mixed with sodium fluorescein. Prepared teeth of each group were treated with AB2, OS, respectively according to the manufacturer's instructions except for dentin surface moisture treatment after acid etching. In group 1 and 3, after acid etching, excess water was removed with wet tissue(Kimwipes), leaving consistently shiny, visibly hydrated dentin surface. In group 2 and 4, dentin surface was dried for 10 seconds at 1 inch distance. The treated teeth were then packed with composite resin(${\AE}$litefil) and light-cured. 12 microscopic samples($60{\sim}80{\mu}m$ thickness) of each group were obtained after longitudinal section and grinding(Exakt cutting and grinding system). Morphological investigation of resin-dentin interface and HLT measurement using CLSM were done. For measurement of SBS, remaining 12 teeth of each group were flattened occlusally to remove all enamel and grinded to 500 grit SiC(Pedemet Specimen Preparation Equipment). After applying DBS on the exposed dentin surface, composite resin was applied in the shape of cylinder, which has 5mm diameter, 1.5mm thickness, and light cured. SBS was measured using Instron with a crosshead speed of 0.5mm/min. It was concluded as follows, 1. HLT of AW(mean: $2.59{\mu}m$) was thicker than any other group, and followed by AD, OW, OD in descending order(mean; 2.37, 2.28, $1.92{\mu}m$). Only OD had statistically significant differences(p<0.05) to AW and AD. 2. There were intimate contact of resin and dentin at the interface in wet bonding groups, but gaps or irregular interfaces were observed in dry bonding groups. 3. The length, diameter, density of resin tags were various even in the same group without significant differences between groups and lots of adhesive lateral branches were observed. 4. There were no statistically significant difference of SBS between AB2 and OS, but SBS of wet bonding groups were significantly higher(p<0.05) than dry bonding groups. 5. There were no consistent relationships between HLT and SBS.

• The Journal of Advanced Prosthodontics
• /
• 제11권2호
• /
• pp.128-137
• /
• 2019

PURPOSE. The aim of this study was to compare the effect of different finishing and polishing techniques on water absorption, water solubility, and microhardness of ceramic or glass-polymer based computer-aided design and computer-aided manufacturing (CAD/CAM) materials following thermocycling. MATERIALS AND METHODS. 150 disc-shaped specimens were prepared from three different hybrid materials and divided into five subgroups according to the applied surface polishing techniques. All specimens were subjected up to #4000 grit SiC paper grinding. No additional polishing has been done to the control group (Group I). Other polishing procedures were as follows: Group II: two-stage diamond impregnated polishing discs; Group III: yellow colored rubber based silicone discs; Group IV: diamond polishing paste; and Group V: Aluminum oxide polishing discs. Subsequently, 5000-cycles of thermocycling were applied. The analyses were conducted after 24 hours, 7 days, and 30 days of water immersion. Water absorption and water solubility results were analyzed by two-way ANOVA and Tukey post-hoc tests. Besides, microhardness data were compared by Kruskal-Wallis and MannWhitney U tests (P<.05). RESULTS. Surface polishing procedures had significant effects on water absorption and solubility and surface microhardness of resin ceramics (P<.05). Group IV exhibited the lowest water absorption and the highest microhardness values (P<.05). Immersion periods had no effect on the microhardness of hybrid ceramic materials (P>.05). CONCLUSION. Surface finishing and polishing procedures might negatively affect physical properties of hybrid ceramic materials. Nevertheless, immersion periods do not affect the microhardness of the materials. Final polishing by using diamond polishing paste can be recommended for all CAD/CAM materials.