• Journal of Welding and Joining
• /
• v.25 no.5
• /
• pp.45-50
• /
• 2007

The Ni-base superalloy GTD111 DS is used in the first stage blade of high power land-based gas turbines. Advanced repair technologies of the blade have been introduced to the gas turbine industry over recent years. The effect of the filler metal powder on Transient Liquid Phase bonding phenomenon and tensile mechanical properties was investigated on the GTD111 DS superalloy. At the filler metal powder N series, the base metal powders fully melted at the initial time and a large amount of the base metal near the bonded interlayer was dissolved by liquid inter metal. Liquid filler metal powder was eliminated by isothermal solidification which was controlled by the diffusion of B into the base metal. The solids in the bonded interlayer grew from the base metal near the bonded interlayer inward the insert metal during the isothermal solidification. The bond strength of N series filler metal powder was over 1000 MPa. and ${\gamma}'$ phase size of N series TLP bonded region was similar with base metal by influence of Ti, Al elements. At the insert metal powder M series, the Si element fluidity of the filler metal was good but microstructure irregularity on bonded region because of excessive Si element. Nuclear of solids formed not only from the base metal near the bonded interlayer but also from the remained filler metal powder in the bonded interlayer. When the isothermal solidification was finished, the content of the elements in the boned interlayer was approximately equal to that of the base metal. But boride and silicide formed in the base metal near the bonded interlayer. And these boride decreased with the increasing of holding time. The bond strength of M series filler metal powder was about 400 MPa.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.326-329
• /
• 2019

Gallium nitride(GaN) has been a superior candidate for the next generation power electronics. As GaN-on-Si substrate technology is mature, there has been new demand for monolithic integration of GaN technology with Si CMOS devices. In this work, (110)Si CMOS process was developed and the fabricated devices were evaluated in order to confirm the feasibility of utilizing domestic foundry facility for monolithic integration of Si CMOS and GaN power devices.

• Transactions of the Society of Information Storage Systems
• /
• v.1 no.2
• /
• pp.175-181
• /
• 2005

SiOB is an essential part of slim optical pickup, where the silicon mirror, LD stand, silicon PD are integrated and LD is flip chip bonded. SiOB is fabricated with bulk micromachining. Especially the fabrication of silicon wafer with stepped concave areas has many extraordinary difficulties. As a matter of fact, experiences and knowledges are rare in the fabrication of the highly stepped silicon wafer. The difficulties occurring in the integration of PD and SiOB, and highly stepped patterning, and silicon mirror roughness and how-to-solve will be discussed.

• Electrical & Electronic Materials
• /
• v.10 no.8
• /
• pp.794-799
• /
• 1997

Poly-Si films have been prepared by solid phase crystallization of LPCVD(low-pressure CVD) amorphous silicon. The crystallinity of poly-Si films has been derived from UV reflectance spectrum and lies in the range between 70% and 80% . From XRD measurement the peak at 28.2$^{\circ}$from (111) plane is dominantly detected in the SPC poly-Si films, The average grain size of poly-Si film is determined by the image of SEM and varies from 4000 $\AA$ to 8000$\AA$. The electrical conductivity of as-deposited amorphous silicon film is about 2.5$\times$10$^{-7}$ ($\Omega$.cm)$^{-1}$ , and 3~4$\times$10$^{-6}$ ($\Omega$.cm)$^{-1}$ of room temperature conductivity is the SPC poly-Si films. The conductivity activation energies are 0.5~0.6 eV or the 500$\AA$-thick poly-Si films.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.9
• /
• pp.417-422
• /
• 2002

ZnO thin films were deposited on various substrates, such as Si-(111), SiO$_2$(5000 $\AA$ by thermal CVD)/Si-(100), and SiO$_2$(2000 $\AA$ by RF sputtering)/Si-(100). The (002)-orientation, surface morphology and roughness, and electrical resistivity of deposited films were measured and compared in terms of substrate. Surface acoustic wave(SAW) filters with a multilayered configuration of IDT/ZnO/SiO$_2$/Si were also fabricated and the IDT was obtained using a lift-off method. From the frequency-response characteristics of fabricated devices, the insertion loss and side-lobe rejection were estimated. The experimental results showed that the (002)-oriented growth nature of ZnO films, which played a crucial role of determining the characteristic of SAW device, was strong1y dependent upon the SiO$_2$buffer.

• Journal of the Korean Vacuum Society
• /
• v.22 no.2
• /
• pp.105-110
• /
• 2013

Single crystalline $In_xGa_{1-x}As$ nanowires are grown on Si (111) substrate via Vapor-Liquid-Solid growth mode using metal-organic chemical vapor deposition. The ternary nanowires have been grown with various growth conditions and examined by electron microscopy. The alloy compositions of the nanowires has been investigated using Energy-dispersive X-ray spectroscopy. We have found that the composition gradient of the nanowire becomes larger with growth temperature and V/III ratio.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.4
• /
• pp.57-61
• /
• 2001

The {111}<112> deformation torture, which originated from the {110}<00l> texture near the surface of hot bands, is not prerequisite for the recrystallized {110}<001> Goss texture. During final annealing, surface-energy-induced selective growth of grains urn at the strip surface of 3%Si-Fe alloys containing 6ppm bulk content of sulfur. With decreasing final reduction, the probability that Goss grains survive under the highly segregated sulfur atmosphere and have a chance for later surface-energy-induced selective growth becomes higher, resulting in high magnetic induction.

• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.220-223
• /
• 2001

Pb가 10% 과잉되고 Zr : Ti = 52 : 48 조성을 갖는 PZT sol이 Pt(3500Å)/Ti(400Å)/SiO₂(3000Å)Si(525㎛)기판 위에 스핀 코팅법으로 반복 코팅된 후, 450℃에서 10분, 650℃에서 2분간 반복 열처리되었다. 이와 같이 다양한 두께로 적층된 박막은 각 시편에 대해 최종적으로 650℃ 30분 동안 어닐링 처리되었다. 제조된 PZT 박막의 두께는 4100Å에서 1.75㎛사이의 4종이었다. 이어서 스퍼터링법으로 Pt전극이 PZT 막 위에 증착되었다. 제조된 PZT 박막의 결정 구조 조사를 위해 XRD, 그리고 미세 구조 및 전기적 특성을 알아보기 위해 FESEM과 P-E 이력 곡선이 각각 관찰되었다. 4100Å에서 1.75㎛까지 두께 증가에 따른 장비상의 포화 이력 한계로 잔류 분극(Pr)값이 25μC/㎠에서 다소 감소되었다. 측정된 X선 회절 결과에서 최초 4회 코팅시 perovskite 결정 구조로 성장한 결정립은 (111)배향이 우세하었으나, 두께가 증가됨에 따라 (111)/(110)값이 감소되었으며, 이를 통해 두께 증가에 따른 (111)배향성이 다소 감소됨을 알 수 있었다. 이상의 결과로부터 제조된 PZT 박막은 큰 힘과 높은 내전압 특성을 갖는 마이크로 압전 액츄에이터에 적용될 수 있을 것으로 생각되었다.

• Journal of Korean Vacuum Science & Technology
• /
• v.2 no.1
• /
• pp.49-54
• /
• 1998

The effect of deposition paratmeters on the solid-phase crystallization of amorphous silicon films deposited by plasma-enhanced chemical vapor deposition has been investigated by x-ray diffraction. The amorphous silicon films were prepared on Si(100) wafers using SiH4 gas with and without H2 dilution at the substrate temperatures between 12$^{\circ}C$ and 38$0^{\circ}C$. The R. F. powers and the deposition pressures were also varied. After crystallizing at $600^{\circ}C$ for 24h, the films exhibited (111), (220), and (311) x-ray diffraction peaks. The (111) peak intensity increased as the substrate temperature decreased, and the H dilution suppressed the crystallization. Increasing R.F. powers within the limits of etching level and increasing deposition pressures also have enhanced the peak intensity. The peak intensity was closely related to the deposition rate, which may be an indirect indicator of structural disorder in amorphous silicon films. Our results are consistent with the fact that an increase of the structural disorder I amorphous silicon films enhances the grain size in the crystallized films.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2001.11a
• /
• pp.79-79
• /
• 2001