• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.104-111
• /
• 2009

This paper shows the behaviors of macro- and micro-structures and mechanical properties for specimen's welding region welded by FSW. according to welding conditions with 5mm thickness aluminum 5083O alloy plate. It apparently results in defect-free weld zone in case traverse speed was changed to 32 mm/min under conditions of anti-clockwise direction and tool rotation speed such as 800 and 1250 rpm with tool's pin diameter of 5 ${\Phi}mm$ and shoulder diameter of 20 ${\Phi}mm$, pin length of 4.5 mm and tilting angle of $2^{\circ}$. The ultimate stress of ${\sigma}_T=331$ MPa and the yield point of 147 MPa are obtained at the condition of the travel speed of 32 mm/min with the tool rotation speed of 1250 rpm. There is neither voids nor cracks on bended surface of $180^{\circ}$ after bending test. The improvement of toughness after impact test was found. The lower rotating and traverse speed became, the higher were yield point, maximum stress and elongation(%) with the stresses and the elongation(%) versus the traverse speed diagram. Vickers hardness for cross section of welding zone were also presented. The typical macro-structures such as dynamically recrystallized zone, thermo-mechanically affected zone and heat affected zone and the micro-structures of the transverse cross-section were also showed. However, the author found out that the region of 6mm far away from shoulder circumference was affected by friction heat comprehensively, that is, hardness softened and that part of micro-structures were re-solid-solution or recrystallized, the author also knew that there is no mechanically deformation on heat affected zone but there are the flow of plastic deformation of $45^{\circ}$ direction on thermo-mechanically affected zone and the segregation of Al-Mg on nugget. The solid solution wt(%) of parent material as compared against of friction stir welded zone was comprehensively changed.

• Clinics in Shoulder and Elbow
• /
• v.11 no.2
• /
• pp.196-200
• /
• 2008

Kimura's Disease is a very rare, chronic inflammatory disorder with an unknown etiology, and this illness is primarily seen in young Asian males. The typical clinical features consist of painless subcutaneous masses in the head or neck region, and especially in the salivary gland and submandibular region. It is often accompanied with a regional lymphadenopathy, peripheral blood eosinophilia and elevated serum IgE levels. Histologically, it is characterized by prominent germinal centers in the involved lymph nodes, together with eosinophilic infiltration in these lymph nodes. The treatment modalities for this disease are steroid therapy, radiation therapy and surgical excision. Its clinical course is of a benign nature. We report here on a case of a 28 year old man who had a soft tissue mass in his left arm. We excised this mass and the microscopy confirmed that he suffered from Kimura's disease on microscopic examination in his left distal arm.

• Journal of Fashion Business
• /
• v.6 no.6
• /
• pp.78-88
• /
• 2002

The purpose of this study is to provide for some basic data useful to production of the apparels fit and measured well for the Chinese men. For this purpose, 389 men aged between 20 and 49 and living in Beijing and Shanghai, China were sampled to be measured for their constitutions. Then, their constitutions were classified and thereupon, according to the Men's Wear Specifications (GB/T 1335.1-1997), National Standards of People's Republic of China. The collected data were statistically processed using SAS 6.12 for technical statistical analysis, correlation analysis, factor analysis, group-wise analysis. The results of this study can be summarized as follows; 1. As a result of the factor analysis aiming to determine Chinese men's constitutional components, five components could be identified: constitutional obesity, lateral body size, longitudinal body size, shoulder and back width, and shoulder drooping. 2. As a result of classifying Chinese men's constitutions according to drop measurements, four types could be identified. Y type had the lowest obesity and the highest longitudinal body size. A type had a lower obesity and had an average longitudinal body size. B Type had the second highest obesity, the smallest longitudinal body size and shoulders/back width. C Type had the highest obesity, upper body length and shoulders/back width. 3. In terms of distribution, 'B' type (39.10%) of the sample, followed by 'A' type (29.26%), 'C' type (19.95%) and 'Y' type (11.70%). In all, the results of this study suggests that 'B' type represents the Chinese men in contrast with GB specifying that 'A' type represents the Chinese men. On the other hand, Beijing region was dominated most by 'B' type (37.06%), followed by 'A' type (28.82%), 'C' type (22.35%) and 'Y' type (11.76%), while Shanghai region was dominated most by 'B' type (41.13%), followed by 'A' type (31.21%), 'C' type (19.15%) and 'Y' type (8.51%).

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.51-61
• /
• 1993

A systematic approach of the energy method is proposed for analysis of axisymmetric deep drawing in which the total deforming region is divided into five sections by the geometric characteristic. The corresponding solution is found through optimization of the total energy dissipation with respect to some parameters assumed in the kinematically admissible velocity field defined over each region. The sheet blank is divided into three-or five-layers to consider the bending effect. For the evaluation of frictional energy, it is assumed that the blank holding force acts on the outer rim of the flange and that the contact pressure acting on punch shoulder or die shoulder has uniform distributions, respectively. The computed results by the present method are compared with the experiment and the computed results by the elastic-plastic finite element method for the distribution of thickness strain and the relation between the punch stroke and punch load. The results for the case of multi-layers show better agreements than for the case of a single layer in load vs. stroke relation and strain distribution. It is thus shown that the multi-layer technique can be effectively employed in analyzing axisymmetric deep drawing in connection with the energy method.

• Journal of the Ergonomics Society of Korea
• /
• v.25 no.3
• /
• pp.17-24
• /
• 2006

In this paper, we propose a stress analysis on foot by lifting task attitudes. Maximum force and peak pressure were measured on 8 body regions by Pedar system in order to analysis the stress which is affected by task style and angle on foot when Manual Materials Handling task. As for the peak pressure of the whole foot as to the task height during the lifting task, the height from Knuckle to Shoulder was the least in the peak pressure. Also, as for the maximum force and the peak pressure of the whole foot as to the task angle during the lifting task, it could be seen that the more an angle increases, the stress influencing on a foot jumps. As for the maximum force and the peak pressure by foot region as to the task height in case of the lifting task, the height from Knuckle to Shoulder is indicated the smallest value in the maximum force and the peak pressure, thus there is necessary to attain the work design that considered this. Also, as for the maximum force by foot region as to the task angle in case of the lifting task, 0° tasking is indicated to be least, thus there is necessity to be attained the tasking design in a bid to prevent the existence of an angle. The results of this paper are thought to be helpful to the suitable work design, to the prevention of musculoskeletal disorders related to the lower limbs, and to the design of ergonomic safety shoes.

• Korean Journal of Applied Biomechanics
• /
• v.15 no.2
• /
• pp.57-67
• /
• 2005

The purpose of this study was to analyze the kinetic factors of the golf driver swing using the Inverse Dynamics function. For this purpose, joint force were calculated. In order to test the possibility of Inverse Dynamics function(motion-dependent interaction), a triple segmental system was set for wrist, left shoulder and lumbar and joint force working on the anatomical joint region was estimated. For this study, 7 professional golfers were sampled, and then, their driver swings were recorded with two high-speed digital video cameras (180 frames/sec.) to be synthesized into 3-dimensional images and coordinated. Then, Eular's equation was used to produce some kinematic data, which were used to calculate joint force and torque with Newton's function. All data were calculated using LabVIEW 6.1 graphic program. The results of this study can be summarized as follows; It was found that the joint force was generated on wrist, shoulder and lumbar joints in the direction of the target, and that the joint force was stronger in the direction of target immediately before impact. The joint force was generated towards the target to activate the nodes, and then, it was generated in the reverse direction to increase the speed during impact.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2017.01a
• /
• pp.9-12
• /
• 2017

본 논문에서는 어깨 초음파 영상을 분석하여 인대 손상(Tear) 영역을 추출하는 방법을 제안한다. 제안된 방법은 초음파 영상에서 ROI(Region of Interest) 영역을 추출하고 추출된 ROI 영역에서 사다리꼴 형태의 소속 함수를 적용한 퍼지 스트레칭 기법을 이용하여 명암 대비를 높인다. 명암 대비가 조정된 ROI 영역에서 밝기 평균 이진화 기법을 적용하여 ROI 영역을 이진화한다. 이진화가 적용된 ROI 영역에서 워터쉐드 기법을 적용하여 연골과 힘줄의 후보 영역들을 추출한다. 추출된 연골과 힘줄의 후보 영역들 중에서 위에서 아래로 스캔하여 수평 너비가 가장 큰 영역에 해당하는 힘줄 영역의 상단 경계선을 추출한다. 그리고 아래에서 위로 스캔하여 수평 너비가 가장 큰 영역의 상단 경계에 스플라인 곡선을 적용하여 연골 영역의 상단 경계선을 추출한다. 힘줄 영역의 상단 경계선과 연골 영역의 상단 경계선 양 끝에 2차 함수 곡선을 적용하여 곡선 사이의 양자화할 영역을 추출한 후, SOM 기법을 적용하여 인대 손상 후보 영역을 양자화한다. 양자화된 인대 손상 후보 영역을 분석하여 어깨 힘줄의 손상 영역과 비손상 영역을 구분하고 인대 손상(Tear) 영역을 추출한다. 제안된 방법을 어깨 힘줄이 있는 초음파 영상을 대상으로 실험한 결과, 인대 손상(Tear) 영역이 비교적 정확히 추출되었다.

• Journal of Fashion Business
• /
• v.10 no.5
• /
• pp.58-73
• /
• 2006

The purpose of this study was to improve of fittness and coverage rate of exporting domestic clothing to China for Chinese Adult Female. For study, It was measured 1381 female women aged between 19 and 50 who resident in Beijing and Shanghai in China. as a sample, 1360 female women was seleted for development of apparel sizing system. As for the method of this study was made of 111 items by indirect measures done during Jun. 23 $\sim$ Aug. 7, 2004. Data analysis were processed by SPSS WIN 10.0 Program was used to for technical statistical analysis, correlation analysis, factor analysis, ANOVA(t-test and F-test), duncan's multiple test. The result was as follows: Chinese Adult women's constitutional components determined by factor analysis, six components could be identified: factor 1:constitutional obesty and width size, factor 2: longistudinal body size, factor 3: shoulder form and size, factor 4: longistudinal upper body size, factor 5: under body size, factor 6: shoulder dropping. According to the Women's Wear Specifications(GB/T 1335.2-1997) by drop, body types of Chinese Adult female was classified into six types, it was Y, A, B, C and Z, D. In order, A type as standard somatotype(49.8%), B type(26.9%), Y type (18.8%), C type(2.9%). Y type had the average height and shoulder, bust girth. They were slimmer in overall terms. A type had a normal obesity and body size in height, shoulder, bust girth. They were average Chinese Women. B type had a smaller then A type. They were more obes and thick waist girth. C type had the highest obesity, the widest shoulder and bust girth, and thick waist girth. The characteristics of each body type following the body type structure factor are Y-type for slender type, A-type for standard type, B-type for slightly large type, and C-type for obese type. For each region, the Beijing area had in the order of A-type, Y-type, B-type and C-type, and the Shanghai area had in the order of A-type, B-type, Y-type and C-type.

• Journal of Digital Convergence
• /
• v.15 no.8
• /
• pp.465-476
• /
• 2017

This study attempted to investigate the effects of gold therapy on myofascial pain syndrome(MPS) in the neck, back and shoulder in comparison to stone therapy and verify its availability as an efficient nursing mediator in clinical trials. For this, therapy was given to a total of 20 women in two groups (gold therapy group, stone therapy group: 10 persons each) living in the capital region three times a week (40 min. at a time) for two weeks. In both groups, a statistically significant decrease was found in the following after the treatment: neck circumference, shoulder width, width of the inferior angle of scapula, shoulder thickness and waist circumference (p<0.001). In terms of differences, the gold therapy group was greater than the stone therapy group. In both groups, a statistically significant increase was observed after treatment in the following: cervical lateral bending (right), cervical lateral bending (left), cervical flexion and cervical extension angle (p<0.001). In terms of differences, the gold therapy group was greater than the stone therapy group. In conclusion, this study seems to show that gold therapy is a nursing intervention option having effective fascial relaxation and pain relief for the neck, back and shoulder. Therefore, it would be valuable as safe, non-invasive therapy.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.8
• /
• pp.1262-1272
• /
• 2009

The study is classifies the figures of obese women aged 20-50 with an over 25 BMI from the data of the fifth Size Korea in 2005. As the result of conducting the factor analysis for segmenting the shape, Factor 1, Factor 2, Factor 3, and Factor 4 are respectively derived as the factor on a volume, the factor on the size of the vertical direction, the factor on the shoulder region, and the factor on the body length balance. As the result of conducting the cluster analysis using 4 factors (scores extracted from the analysis of factor analysis) the body type of obese women was classified into four types. The name of shape was specified by combining 'P' (an abbreviation of petite) that indicated the height (smaller than 155cm) among the height names of KS standard, 'R' (abbreviation of regular) that indicated the height (155cm-165cm) and the body characteristics. Type 1 had the longest length, and normal circumference, thickness, and width but with the developed shoulder. Type 1 was classified as a robust, 'Plus-RH'. Type 2 had the middle height, the shortest length of the upper part, a relatively-long length of the lower part of body. Type 2 shows the characteristics of a small body that was classified as 'Plus-PI'. The most obese body was Type 3 that had the normal length and shoulder size but showed the longest length of the upper part of the body; it was classified as 'Plus-PO'. Type 4 as the small shape had a potbelly and showed the characteristics of the shortest body classified as 'Plus-Pb'.