• Bulletin of the Society of Naval Architects of Korea
• /
• v.3 no.1
• /
• pp.33-45
• /
• 1966

The effect of thermal stress on a ship's hull is not considered to be serious by most naval architects. Frequently, however, cracking of hulls has been reported which occurred at sea while there were no external forces except the heat from the sun. Detailed investigations have been made of these reports and it has been reliably determined that the damage was initiated by solar heating. The author is not interested in all steel ship or in the applicability and validity of the formular itself, as it has already been proven by the experiments such as S.S. Boulder Victory. The author therefore proceeds directly to calculate the stress distribution on he hull and superstructure of the prototype model ship. These calculations are based on the experimental nonsymetrical temperature gradient data taken earlier on the Boulder Victory. The calculations were made principally to determine the extent of stresses which occurred on an all-steel ship in one case and secondly, those that occurred on a ship with a steel hull and an aluminum superstructure. From the calculations, the author expected the stress distribution of the two case would show distinctly different aspects, but the acquired results were very similar. Generally, at the point of junction of the steel hull and aluminum superstructure sharp peak stresses appeared. At the juncture of the superstructure and the main deck the ship with the aluminum superstructure registered almost 1000 psi more stress than did the ship with the all-steel construction. In the view of these findings, the author recommends to ship designers that pay particular attention to the point of junction of steel and aluminum plate. The author has proven that it is extremely important that a greater safety factor be used at the aluminum-steel junction point than at any other point. Although thermal effects cause high juncture-point stresses in all-steel ships, they are not nearly as critical as in ship constructed of two or more metals.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.1 no.2
• /
• pp.209-220
• /
• 1997

DBS offers actual services to mass-media and communication system of very broad region in information society. Especially, the DBS is the only system to access TV broadcasting service on a sailing ship. But the ship's DBS receiver is required a complex antenna tracking system because ships are under complex moving such as pitch, roll, and yaw etc. This study is motivated to develop a tracking antenna system to receive the koreasat on small silo ship. Therefore, this system is researched to small size, light weight, simple operation, and low cost of the product. The mount structure have been a compact size and easy operation to the Az/El 2-axis type which is operated by step motor. And it is very useful on a ship in the around sea of korean peninsula. The antenna has a plate type of micro-strip array, and is a domestic production. The vibration sensor is selected to gyro sensor of ultra-sonic rate type for ship's moving control. Tracking method is used the step-tracking algorithm, and the ship's moving compensation is adapted to the closed loop control method by ship's moving detection of gyro sensor. Tracking test is operated by the ship's moving simulator, we examined the actual receiving state on sailing shipboard in the near sea of korean peninsular.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.5
• /
• pp.396-403
• /
• 2011

The concept of an air lubrication has long been an object of attention since it can be utilized to reduce the frictional resistance, and what is more, it is eco-friendly. The present study examines the basic characteristics of an air cavity with intention of applying the air lubrication technology to the reduction of the resistance of a ship without excessive power increment. For the purpose, an air cavity was created at the bottom of a flat plate by injecting air behind a backward step and the hydrodynamic properties of the air cavity and the surrounding flow has been investigated experimentally and numerically. The influence of the step height and the air flow rate have been more carefully studied since they are presumed to be the main parameters affecting the characteristics of an air cavity. The results indicates that the shapes of the air cavities attached on the flat plate become "U" or "V" type depending on the incoming flow velocity and air flow rate. The study also confirms that the length of the air cavity increases with increase in air flow rate but there is a certain critical limit in the flow rate above which increase in the air cavity length is no more evident.

• Journal of the Society of Naval Architects of Korea
• /
• v.38 no.4
• /
• pp.75-82
• /
• 2001

Static loadings on ship structure induced either by water pressure before service such as a tank test and ballasting or by cargo pressure during first laden voyage cause relatively much greater stress than dynamic loadings induced by wave. With these static pre-loadings, the initial residual stresses around welded joint, where fatigue strength is concerned(in most cases, where stress concentration occurs) are expected to be shaken-down in a great extent by the elasto-plastic deformation behavior of material. Therefore, it is more resonable to assess the fatigue strength of ship structure with S-N data which have taken into account the effect of shaken-down residual stresses(re-distributed stresses) on the fatigue strength. In this research work, the re-distribution of residual stresses by the tensile pre-loading is measured using an ordinary sectioning method for specimens of padding plate weldment. Fatigue tests are performed also to evaluate the fatigue strength of the both as-welded and pre-loaded specimens.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2009.09a
• /
• pp.80-86
• /
• 2009

In order to improve productivity of large container ship construction, large heat input and/or high productive welding technologies are necessary. This can be achieved by the joint research and cooperation among steel maker, welding consumable company, welding equipment company and ship yards. Two electrodes SAW process is effective the plate butt welding and partial joint welding, while FGB welding process is for the connection of block to block joint. The higher strength and thicker steel is developed, the more reliable welding procedure such as two electrodes EGW including light weight welding equipment should be developed.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.22 no.2
• /
• pp.12-26
• /
• 1985

This paper describes the experimental method to predict the propeller induced fluctuating pressure on the hull surface. Cavitations of the three model propellers with varying degree of skews, $0^{\circ},\;36^{\circ}\;and\;72^{\circ}$, were observed and the fluctuating pressure induced by the cavitating propellers in the flat plate above these propellers were measured simultaneously at 9 points in the wake field generated by the wire-mesh screens. Another model propeller designed for the dummy model ship was tested in a similar way behind the dummy model ship. The effects of skew variation on the cavitation patterns and fluctuating pressures were illustrated, and the influence of tip-clearances on the fluctuating pressures was also demonstrated. As a result, it is shown that the level of fluctuating pressure and cavity extent could be controlled to some extent by introducing the skews and tip clearances.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.16 no.3
• /
• pp.1-8
• /
• 1979

Various approaches to the analysis of stiffened plating in ship structures have been proposed by a number of researchers. Among them, the finite element method is known to be the most powerful method. However, for many parts of ship's structure having simple geometry and boundary conditions, the F.E.M. is often extravagant and unnecessary. In this paper, the authors have attempted to introduce the finite strip method which was proposed by Y.K. Cheung to avoid the difficulties involved in F.E.M. The results of calculations on the displacements and stresses in various plates with or without stiffeners were satisfactory, which shows the F.S.M. is useful for structural analysis of ship's plating.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.1
• /
• pp.41-50
• /
• 1998

The detemination of sound pressure radiated from peoriodic plate structures is fundamental in the estimation of noise levels in aircraft fuselages and ship hull structures. As a robust approach to this problem, here a very general and comprehensive analytical model for predicting the sound radiated by a vibrating plate stiffened by periodically spaced orthogonal symmetric beams subjected to a sinusoidally time varying point load is developed. The plate is assumed to be infinite in extent, and the beams are considered to exert both line force and moment reactions on it. Structural damping is included in both plate and beam materials. A space harmonic series representation of the spatial variables is used in conjunction with the Fourier transform to find the sound pressure in terms of harmonic coefficients. From this theoretical model. the sound pressure levels on axis in a semi-infinite fluid (water) bounded by the plate with the variation in the locations of an external time harmonic point force on the plate can be calculated efficiently using three numerical tools such as the Gauss-Jordan method, the LU decomposition method and the IMSL numerical package.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.3
• /
• pp.222-226
• /
• 2012

When ship blocks are erected or pre-erected, most blocks will be at outdoors where they are not protected from weather and exposed to ray of the sun. A deck plate compared to those in radiation heat transfer from the sun will have higher temperature than it of ambient air, and will expand more than lower laying structures whose temperatures are similar with air. But deck plates and under-structures are connected, so the deck plate will be under out-of-plane deformation rather than expand in length. In this study, we considered the temperature difference between air and plate as a major parameter of out-of-plane deformation, and analyzed how much additional deformation would take place. In addition, when a deformation could take place was also analyzed based on the initial deformed shape of deck plate. Because the accuracy inspections of deck plate will be done during daytime, conventional accuracy check results on sunny day could make us feel unfair. Thus resonable datum about momentary additional out-of-plane deformation due to environmental effects have been determined. The real deformation values can be specified even under enlarged deformations by radiation-expansion.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.1
• /
• pp.135-139
• /
• 2009

In the line heating for the plate forming of a ship's hull, an in line assessment of completion is necessary for an automated production system. In the current curved plate forming process, a fabricated plate is compared to a template that is made in the mold loft and is used for the determination of the heating line for the next step. In this paper, a new method is presented for the in line assessment of completion for curved plate forming. This method uses a 3-D scanner. For the registration of the scanned data for a surface and the target surface, the ICP (Iterative Closest Points) method was adopted. A computer program was developed to carry out the registration, check for similarities, visualize the surface, and control the results. This program was applied to a sample curved plate forming process.