• Journal of Welding and Joining
• /
• v.15 no.3
• /
• pp.88-98
• /
• 1997

Welding defects, such as porosity and spike, have sometimes occurred in deep penetration electron beam welds. These defects are known to be one of the serious problem in electron beam welds. So, effects of active parameters ($a_b$) on bead shape and occurrence of defects in electron beam welds of heavy section 9%Ni steel plates were investigated. Partial penetration welding in flat position, and deep penetration welding of 10 ~ 28mm depth were investigated in this study. It is desirable to select low accelerating voltage and above the surface focus position $a_b$$\geq$1.2 at which a wine-cup shaped bead is obtained to avoid the welding defects such as spike and root porosity. When the accelerating voltage of electron beam was low (90kV), active parameter ($a_b$) did not influence on the bead width, penetration depth and weld defects significantly. However, in case of high voltage ($\geq$120kV), active parameter ($a_b$) was sensitively associated with penetraton depth and weld defects, i.e. when the active parameter (($a_b$) was in the range of 0.6 to 1.0, the depth of penetration was always over the target (23mm), while the depth of penetration was dramatically decreased with further increase of active parameter ($a_b$). The weld defects were decreased with the increase of active parameter $a_b$ resulting in the decrease of energy density of the focused beam in the root part of fusion zone.

• Journal of the Korean Ceramic Society
• /
• v.34 no.9
• /
• pp.927-934
• /
• 1997

Static and cyclic fatigue tests were carried out for alumina specimen to study the statistical analyses (normal, lognormal and Weibull distribution) of fatigue lifetime data and nominal initial crack length data. Fatigue lifetime data followed Weibull distribution better than normal or lognormal distribution, for the shape parameter of the notched specimen was larger than that of the unnotched specimen. The nominal initial crack length data obtained from fatigue lifetime followed the lognormal and Weibull distribution better than normal distribution, for the coefficient of variation of the unnotched specimen was larger than that of the notched specimen, and shape parameter of unnotched specimen was smaller than that of the notched specimen.

• Journal of the Korean Data and Information Science Society
• /
• v.19 no.3
• /
• pp.995-1006
• /
• 2008

This article deals with the one-sided hypothesis testing problem in inverse Gaussian distribution. We propose Bayesian hypothesis testing procedures for the one-sided hypotheses of the shape parameter under the noninformative prior. The noninformative prior is usually improper which yields a calibration problem that makes the Bayes factor to be defined up to a multiplicative constant. So we propose the objective Bayesian hypothesis testing procedures based on the fractional Bayes factor, the median intrinsic Bayes factor and the encompassing intrinsic Bayes factor under the reference prior. Simulation study and a real data example are provided.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.12
• /
• pp.143-151
• /
• 1999

The shape of surface micro-crack is very irregular due to nonhomogeneous microstructure but is very important in respect to qualitative estimation of fatigue life. Fractal geomety can quantify the shape of surface mciro-crack. Fractal dimension is measured for surface micro-cracks with coast line and box counting method and estimates cycle ration in Al 2024-T3. The average fractal dimension $D_{favg}$ of surface micro-cracks has 3-parameter weibull distribution and location parameter is nearly constant but shape parameter decreases as cycle ration increases. The fractal dimension by coast line method is measured for individual surface micro-crack but the fractal dimension by box countin method is measured for all the surface micro-cracks under sampling area. Therefore, This paper shows fractal dimension $D_{fb}$ can predict cycle ratio $N/N_f$ more convenient than fractal dimension $D_{favg}$.

• Journal of the Korean Data and Information Science Society
• /
• v.26 no.6
• /
• pp.1583-1592
• /
• 2015

This paper deals with the problem of testing on the shape parameter in the log-logistic distribution. We propose default Bayesian testing procedures for the shape parameter under the reference priors. The reference prior is usually improper which yields a calibration problem that makes the Bayes factor to be defined up to a multiplicative constant. We can solve the this problem by the intrinsic Bayes factor and the fractional Bayes factor. Therefore we propose the default Bayesian testing procedures based on the fractional Bayes factor and the intrinsic Bayes factors under the reference priors. Simulation study and an example are provided.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.5C no.4
• /
• pp.155-160
• /
• 2005

This paper addresses the discharge characteristics of cross-linked polyethylene according to void by the Weibull function. It analyzes discharge number and amount of discharge using Weibull distribution to identify the inter-relationship between partial discharge and defect. We detected a 10 second discharge. The applied voltage increased by 1 [kV] at discharge inception voltage. As a result, in a no-void specimen, the shape parameter was consistent according to the increase of voltage, whereas, in a void specimen, it increased according to the increase of voltage. As the result, the shape parameter expressed a fixed value at no-void specimen. However, in void specimen, according to increasing voltage shape parameter rapidly increases.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.10 no.3
• /
• pp.130-134
• /
• 1985

In two-dimensional discrete cosine transform(DCT) coding, the measurements of the distributions of the transform coefficients are important because a better approximation yields a smaller mean square distorition. This paper presents the results of distribution tests which indicate that the statistics of the AC coefficients are well approximated to a generalized Gaussian distribution whose shape parameter is 0.6. Furthermore, from a simulation of the DCT coding, it was shown that the above approximation yields a higher experimental SNR and a better agreement between theory and simulation than the Gaussian or Laplacian assumptions.

• Journal of the Korean Data and Information Science Society
• /
• v.17 no.3
• /
• pp.927-932
• /
• 2006

The techniques for selecting and evaluating prior distributions are studied over recent years which the primary emphasis is on noninformative priors. But, noninformative priors are typically improper so that such priors are defined only up to arbitrary constants which affect the values of Bayes factors. In this paper, we consider the Bayesian hypotheses testing for the Weibull shape parameter based on fractional Bayes factor which is to remove the arbitrariness of improper priors. Also we present a numerical example to further illustrate our results.

• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.127-132
• /
• 2006

Pneumatic cylinders that are usually applied in the factory automation line have complicated failure cause because they are composed of various elements. In this study, we performed life test and performance test of double acting pneumatic cylinders according to the international standards and then analyzed the life and the main failure mode of the cylinders in the same load condition. On the basis of these processes, we can estimate shape parameter for the reliability estimation of pneumatic cylinders and their data analysis of life distribution.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1390-1393
• /
• 2004

In the present industry, three-dimensional colored shape has required for realistic prototype in rapid manufacturing. Z-corporation developed 3D printer which can color three-dimensional prototype but this process can't be adopted to other rapid prototype products and spend much time and cost coloring 3D shape. In this study a new coloring process on three-dimensional surface is proposed for realistic prototype. Three-dimensional surface coloring apparatus is composed of HP ink jet head and X-Y plotter. Distance and angle between ink jet nozzle and 3D surface are set as process parameter. Based on the experiment of process parameters, it is shown that distance and angle affected on printed image on 3D surface. Circle and line shape are chosen as standard image shape because the shape has widely used as standard in 2D printing. Consequently, the distorted image on 3D surface is corrected by transformed input image data.