• Transactions on Electrical and Electronic Materials
• /
• v.2 no.3
• /
• pp.24-27
• /
• 2001

The end point of oxide chemical mechanical polishing (CMP) have determined by polishing time calculated from removal rate and target thickness of oxide. This study is about control of oxide removal amounts on the shallow trench isolation (STI) patterned wafers using removal rate and thickness of blanket (non-patterned) wafers. At first, it was investigated the removal properties of PETEOS blanket wafers, and then it was compared with the removal properties and the planarization (step height) as a function of polishing time of the specific STI patterned wafers. We found that there is a relationship between the oxide removal amounts of blanket and patterned wafers. We analyzed this relationship, and the post CMP thickness of patterned wafers could be controlled by removal rate and removal target thickness of blanket wafers. As the result of correlation analysis, we confirmed that there was the strong correlation between patterned and blanket wafer (correlation factor: 0.7109). So, we could confirm the repeatability as applying for STI CMP process from the obtained linear formula. As the result of repeatability test, the differences of calculated polishing time and actual polishing time was about 3.48 seconds. If this time is converted into the thickness, then it is from 104 $\AA$ to 167 $\AA$. It is possible to be ignored because process margin is about 1800 $\AA$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.12
• /
• pp.2258-2263
• /
• 2006

In this parer, hump characteristics of short-channel nMOSFETs induced by moistures of the ILD(inter-layer dielectric) layer in the shallow trench isolation (STI) process are investigated and the method for hump suppression is proposed Using nMOSFETs with various types of the gate and a measurement of TDS-APIMS (Thermal Desorption System-Atmospheric Pressure ionization Mass Spectrometry), hump characteristics were systematically analyzed and the systemic analysis based hump model was presented; the ILD layer over poly-Si gate of nMOSFET generates moistures, but they can't diffuse out of the SiN layer due to the upper SiN layer. Consequently, they diffuses into the edge between the gate and STI and induces short-channel hump. In order to eliminate moisture in the ILD layer by out-gassing method, the annealing process prior to the deposition of the SiN layer was carried out. As the result, short-channel humps of the nMOSFETs were successfully suppressed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2509-2515
• /
• 2014

In this paper, the conventional vertical structure for VLSI circuits CMOS intend to improve the stress effects of active region and built-in threshold voltage. For these improvement, the proposed structure is shallow trench isolation of moat shape. We want to analysis the electron concentration distribution, gate bias vs energy band, thermal stress and dielectric enhanced field of thermal damage between vertical structure and proposed moat shape. Physically based models are the ambient and stress bias conditions of TCAD tool. As an analysis results, shallow trench structure were intended to be electric functions of passive as device dimensions shrink, the electrical characteristics influence of proposed STI structures on the transistor applications become stronger the potential difference electric field and saturation threshold voltage, are decreased the stress effects of active region. The fabricated device of based on analysis results data were the almost same characteristics of simulation results data.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.10
• /
• pp.838-843
• /
• 2002

Chemical mechanical polishing(CMP) process has been widely used to planarize dielectric layers, which can be applied to the integrated circuits for deep sub-micron technology. The reverse moat etch process has been used for the shallow trench isolation(STI)-chemical mechanical polishing(CMP) process with conventional low selectivity slurries. Thus, the process became more complex, and the defects were seriously increased. In this paper, we studied the direct STI-CMP process without reverse moat etch step using high selectivity slurry(HSS). As our experimental results show, it was possible to achieve a global planarization without the complicated reverse moat process, the STI-CMP process could be dramatically simplified, and the defect level was reduced. Therefore the throughput, yield, and stability in the ULSI semiconductor device fabrication could be greatly improved.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.443-444
• /
• 2002

The uniformity of field oxide is critical to isolation property of device in STI, so the control of field oxide thickness in STI-CMP becomes enormously important. The loss of field oxide in shallow trench isolation comes mainly from dishing and erosion in STI-CMP. In this paper, the effect of slurries on the dishing was investigated with both blanket and patterned wafers were selected to measure the removal rate, selectivity and dishing amount. Dishing was a strong function of pattern spacing and types of slurries. Dishing was significantly decreased with decreasing pattern spacing for both slurries. Significantly lower dishing with ceria based slurry than with silica based slurry were achieved when narrow pattern spacing were used. Possible dishing mechanism with two different slurries were discussed based on the observed experimental results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.25-28
• /
• 2001

Recently, STI(Shallow Trench Isolation) process has attracted attention for high density of semiconductor device as a essential isolation technology. Without applying the conventional complex reverse moat process, CMP(Chemical Mechanical Polishing) has established the Process simplification. However, STI-CMP process have various defects such as nitride residue, torn oxide defect, damage of silicon active region, etc. To solve this problem, in this paper, we discussed to determine the control limit of process, which can entirely remove oxide on nitride from the moat area of high density as reducing the damage of moat area and minimizing dishing effect in the large field area. We, also, evaluated the reliability and reproducibility of STI-CMP process through the optimal process conditions.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.52 no.10
• /
• pp.441-446
• /
• 2003

The chemical mechanical polishing (CMP) process is now widely employed in the ultra large scale integrated (ULSI) semiconductor fabrication. Especially, shallow trench isolation (STI) has become a key isolation scheme for sub-0.13/0.10${\mu}{\textrm}{m}$ CMOS technology. The most important issues of STI-CMP is to decrease the various defects such as nitride residue, dishing, and tom oxide. To solve these problems, in this paper, we studied the planarization characteristics using slurry additive with the high selectivity between $SiO_2$ and $Si_3$$N_4$ films for the purpose of process simplification and in-situ end point detection. As our experimental results, it was possible to achieve a global planarization and STI-CMP process could be dramatically simplified. Also, we estimated the reliability through the repeated tests with the optimized process conditions in order to identify the reproducibility of STI-CMP process.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.3
• /
• pp.18-20
• /
• 2002

In sub-l/4 ${\mu}{\textrm}{m}$ NMOSFET with STI (Shallow Trench Isolation), the anomalous hump phenomenon of subthreshold region, due to capped p-TEOS/SiN induced defect, is reported. The hump effect was significantly observed as channel length is reduced, which is completely different from previous reports. Channel boron dopant redistribution due to the defect should be considered to improve hump characteristics besides considerations of STI comer and recess. 130

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.79.1-79
• /
• 1998

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.723-725
• /
• 1998

STI CMP process are substituting gradually for LOCOS(Local Oxidation of Silicon) process to be available below sub-0.5um technology and to get planarized. The other hand, STI CMP process(especially STI CMP with RIE etch back process) has some kinds of defect like Nitride residue, Torn Oxide defect, etc. In this paper, we studied how to reduce Torn Oxide defects after STI CMP with RIE etch back process. Although Torn Oxide defects which occur on Oxide on Trench area is not deep and not sever, Torn oxide defects on Moat area is sometimes very deep and makes the yield loss. We did test on pattern wafers witch go through Trench process, APCVD process, and RIE etch back process by using an REC 472 polisher, IC1000/SUV A4 PAD and KOH base slurry to reduce the number of torn defects and to study what is the root causes of torn oxide defects.