• 드라이브 ㆍ 컨트롤
• /
• 제21권2호
• /
• pp.23-29
• /
• 2024

Potatoes are one of the world's four major crops, and domestic consumption is currently increasing in Korea. However, the mechanization rate of potatoes is very low, and especially, harvesting is the most labor-intensive task in potato production. In Korea, potato-collecting work depends on manpower, so it is necessary to develop a gathering-type harvester that can be used for processes from digging to harvesting. Therefore, in this study, a self-propelled-type potato harvester was developed, and its performance was analyzed to mechanize harvesting. The potato harvester was developed to have a crawler-type driving part with a 60 hp diesel engine and consisted of a digging part that digs potatoes from the ground, a vertical transporting part that transfers the dug potatoes to the height of the collection bag, a separating part that separates debris, such as stones and soil, and a collecting part that loads the collection box. A field test of the potato harvester was conducted, and performance was evaluated by the damage, loss, and debris mixing proportions, which were 2.5%, 2.8%, and 2.6%, respectively. The working capacity was 1.2 h/10 a. The economic analysis results showed that the cost of harvesting work could be reduced by 12.7% compared to manual harvesting.

• 한국작물학회지
• /
• 제62권2호
• /
• pp.134-142
• /
• 2017

Crop production in rice paddy fields is of great importance because of declining rice consumption and the low self-sufficiency ratio for field crops in Korea. A controlled drainage system (CDS) is recognized as an effective means to adjust water table (WT) levels as needed and control soil water content to improve the soil environment for optimum crop growth. The present study evaluated the effects of a CDS on soil characteristics, including soil water distribution and soybean development in paddy fields. The CDS was installed with two drain spacing (3 m and 6 m) at the experimental paddy field at the National Institute of Crop Science, Miryang, Korea. It was managed with two WT levels (0.3 m and 0.6 m) during the growing season. Soil water content, electrical conductivity and plant available nitrogen content in the soil were significantly greater in the 0.3 m WT management plots than in the 0.6 m plot and the control. At the vegetative stage, chlorophyll content was significantly lower with higher WT control because of excess soil moisture, but it recovered after the flowering stage. Soybean yield increased with WT management and the 0.6 m WT treatment produced the greatest grain yield, $3.38ton\;ha^{-1}$, which was 50% greater than that of the control. The CDS directly influenced outflow through the drains, which significantly delayed nutrient loss. The results of this study indicated that WT management by CDS can influence soil characteristics and it is an important practice for high yielding soybean production in paddy fields, which should be considered the crop growth stages for stable crop production.

• 한국환경복원기술학회지
• /
• 제19권1호
• /
• pp.185-193
• /
• 2016

Purpose of this study is to classify damaged lands according to the cause of the damage and their influences based on characteristic of the damaged lands in DeMilitarized Zone(DMZ) area, and utilize this study as a fundamental study for establishment of ecosystem restoration system. Literature review and field survey have been conducted to review the damage status of DMZ area. For field survey, first year and second year have been conducted, in which type of the damage has been reviewed in this study. In the result, types of damage have been classified into 6 categories: 'alteration of initial landform', 'loss of surface layer', 'land pollution', 'alteration of soil chemical property', 'decline of vegetation', and 'invasion of foreign species'. Restoration for each damage type is as following. First, for alteration of initial landform, the land is restored to the original landform prior to the damage and connection to surrounding ecosystem is considered. Second, for loss of surface layer, lost surface layer is restored or further loss is prevented with stabilization. Third, for land pollution, source of the pollution is eradicated or self-circulation with purification of polluted land is encouraged. Fourth, for alteration of soil chemical property, soil is restored of its original property with eradication of the pollution source and improvement of soil. Fifth, for decline of vegetation, current vegetation and anticipated alteration in future are considered and number of wild species is to be increased based on structure and characteristic of nearby vegetation. Sixth, for invasion of foreign species, prevention of dominance by risky species and facilitation ecological stability with ecological management are to be considered. Influence according to the cause of damage has occurred in secondary(indirect) influence or simultaneous occurrence of several damage types. Considering all these aspects, when type of the damage is complex, restoration process for each of former mentioned 6 damage types with solitary influence should be considered in unison.

• 환경생물
• /
• 제25권3호
• /
• pp.223-227
• /
• 2007

산악형 국립공원지역 내에서 일부 야생동물종이 빠르게 증식하고 있다. 규모가 작고 공원 내 1/3이상의 면적이 사유지인 우리나라 국립공원의 특성상 서식동물수의 증가와 함께 이로 인한 농작물 피해도 함께 급증하고 있다. 농작물에 가장 많은 피해를 주는 위해조수종은 멧돼지 (Sus scrofa)인 것으로 조사되었으며 농작물 채식, 농경지 밟음 등이 대표적인 피해유형으로 나타났다. 이외 고라니 (Hydropotes inermis), 너구리 (Nyctereutes procyonoides), 오소리 (Meles meles)등에 의한 피해도 조사되었다. 대부분의 피해작물은 옥수수, 고구마, 배추 등의 밭작물로서 전체 피해작물의 76.9%에 이르고 있다. 야생동물에 의한 피해는 매년 6월경부터 시작되어 11월까지 계속되었으며 이는 산림 내에서 구할 수 있는 먹이원의 수급현황 및 기후조건과 밀접한 관련이 있다. 피해방제에 대한 자구책으로는 경작지 곳곳에 기피제를 설치하는 방법을 많이 사용하고 있으며 (n=54) 발성체 및 허수아비 등을 설치하는 경우가 있었으나 실제 효과는 극히 미미한 것으로 나타났다. 전체 조사가구의 92.4% (n=187)가 경작면적 1ha이하의 텃밭 수준의 소규모 영농을 하고 있으며 일부 농민들을 제외하고는 피해발생에 대한 민원은 거의 없었다. 이는 야생동물 피해에 대한 법적 제도적 보상체계가 미비되어 있음에 기인하며 객관적인 피해현황 분석기법의 확립과 이를 통한 보상대책과 관리방안이 시급히 마련되어야 할 것으로 사료된다.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2002년도 하계학술발표대회 논문집 제21권 1호
• /
• pp.469-474
• /
• 2002

In recent years, modularization of engine parts has increased the application of plastic products in air intake systems. Plastic intake manifolds provide many advantages including reduced weight, contracted cost, and lower intake air temperatures. These manifolds, however, have some weakness when compared with customary aluminium intake manifolds, in that they have low sound transmission loss because of their lower material density. This low transmission loss of plastic intake manifolds causes several problems related to flow noise, especially when the throttle is opened quickly. The physical processes, responsible for this flow noise, include turbulent fluid motion and relative motion of the throttle to the airflow. The former is generated by high-speed airflow in the splits between the throttle valve and the inner-surface of the throttle body and surge-tank, which can be categorized into the quadrupole source. The latter induces the unsteady force on the flow, which can be classified into the dipole source. In this paper, the mechanism of noise generation from the turbulence is only investigated as a preliminary study. Stochastic noise source synthesis method is adopted for the analysis of turbulence-induced, i.e. quadrupole noise by throttle at quick opening state. The method consists of three procedures. The first step corresponds to the preliminary time-averaged Navier-Stokes computation with a $k-\varepsilon$ turbulence model providing mean flow field characteristics. The second step is the synthesis of time-dependent turbulent velocity field associated with quadrupole noise sources. The final step is devoted to the determination of acoustic source terms associated with turbulent velocity. For the first step, we used market available analysis tools such as STAR-CD, the trade names of fluid analysis tools available on the market. The steady state flows at three open angle of throttle valve, i.e. 20, 35 and 60 degree, are numerically analyzed. Then, time-dependent turbulent velocity fields are produced by using the stochastic model and the flow analysis results. Using this turbulent velocity field, the turbulence-originated noise sources, i.e. the self-noise and shear-noise sources are synthesized. Based on these numerical results, it is found that the origin of the turbulent flow and noise might be attributed to the process of formulation and the interaction of two vortex lines formed in the downstream of the throttle valve. These vortex lines are produced by the non-uniform splits between the throttle valve and inner cylinder surface. Based on the analysis, we present the low-noise design of the inner geometry of throttle body.

• 산업진흥연구
• /
• 제6권4호
• /
• pp.39-45
• /
• 2021

본 연구는 위니캇의 이론을 중심으로 상담자의 중간대상 역할을 문헌연구를 통하여 제시하였다. 발달과정에서 유아가 어머니와 절대적 의존에서 상대적 의존으로 넘어갈 때 불안을 겪는데 이때 중간대상인 인형, 손 빨기 등이 유아의 불안을 감소시킨다. 이처럼 상담자의 중간 대상 역할은 상실 경험에 대한 분리불안과 우울 불안을 완충시켜주고, 전능 환상에서 현실 세계로 매개하여준다. 중간대상은 새로운 대상으로 현실에서 적응하도록 이바지 하는 기능을 가지고 있다. 그리고 중간대상과 중간현상을 통하여 분리 개별화 단계로 이어진다. 전능한 창조와 파괴, 그리고 현실에 적응하기 위해 존재하는 실제적인 타자에 대한 감각을 체득한다고 할 수 있다. 충분히 좋은 어머니는 유아의 전능성을 의미 있게 만들어 준다. 이러할 때 참자기는 유아의 약한 자아를 성장하게 하여 자신의 삶을 살도록 이끌어 준다. 어머니가 유아의 욕구를 채워주지 못할 경우 환상과 자발적 충동이 결핍된다. 즉, 어머니가 유아의 욕구를 반영해 주지 못할 때 유아가 어머니의 기분을 살피게 되어 참자기를 포기하고 거짓 자기를 만들게 된다. 절대적 의존기의 병리는 충분히 좋은 어머니의 공감과 안아주는 환경의 실패로 인해 발생한다. 이때 아이는 전능 환상의 붕괴를 경험하고 멸절 불안을 경험하게 된다. 그러므로 상담현장에서 상담자의 중간대상 역할을 통해서 내담자의 분리불안과 우울 불안을 감소시켜서 편안하고 안정된 환경을 제공할 때 효율적인 상담을 진행할 수 있다.

• 한국융합학회논문지
• /
• 제7권1호
• /
• pp.197-203
• /
• 2016

본 연구에서는 AHP 분석의 결과로 도출된 TPM의 스텝활동 중 가장 중요한 활동들과 기업성과와의 관계를 모형으로 구축한다. 그리고 이러한 스텝활동들이 매개변수를 통해 기업성과에 영향을 미치는지를 융합적 관점에서 분석하고자 하였다. 4개의 스텝활동인 현장불합리 및 로스개선, 준비 및 5S 활동 기본조건 체계구축, 초기청소, 설비효율의 로스분석을 독립변수로 선정하고 TPM 활동수준을 매개변수로 하여 종속변수인 기업성과에 어떠한 영향을 미치는가를 분석하였다. 분석결과 4개의 스텝활동들은 기업성과에 직접 효과를 나타내고 있지는 않지만, TPM 활동수준이 매개변수로 투입된 경우에는 기업성과에 영향을 미치는 완전매개효과를 갖는 것으로 나타났다. 즉, TPM 활동수준은 매개변수로서의 역할을 하는 것으로 나타났다. 따라서 TPM에 참여한 사람들의 설비에 대한 자신감, 자기계발의 의식, 개인 업무에 대한 명확한 관리 등에 대한 인식수준이 높을수록 TPM활동은 성공적으로 기업의 성과에 공헌할 수 있는 것으로 해석할 수 있다.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.967-976
• /
• 1996

Straw and other fibrous by-products are inevitably produced during cereal production and have traditionally been used for many purposes including feeding animals . The potential of these by -products as a feed resource for ruminants is being increasingly appreciated (FAO , 1977). In the future, the amount of cereals fed to farm animals will have to be reduced and livestock will have to rely more on by-products such as straw. The method of animal production can be classified by the major portion of feed. One is animal forage and the other is grains. In Korea , livestock farmers normally depend more than 70% upon grains for the feed stuff. The livestock production system causes the unbalance of nutrition, and results in low productivity of animal farming. In many livestock farms in Korea the rice straw is using as a major forage and the amount of rice straw fed takes 46% of total amount of required forages. Especially the rice straw is mainly using during spring, fall and winte season. However, there are still lots of problems to solved such as harvesting cost, transportation between rice farm ad livestock farm, and quality loss during drying and storage . Therefore the mechanization of straw harvesting is urgently needed to use the renewable agricultural by-products and to overcome the shortage of animal forage. The objective of this research is to develope a straw harvester with new concept which can solve the problems of the quality loss and the labor cost during drying in a field, collecting , and storage. The developed straw harvester is self-propelled machine rebuilt by rice combine and equipped with the pick-up device, the macerater and the mat-forming device.

• 화약ㆍ발파
• /
• 제38권4호
• /
• pp.46-52
• /
• 2020

수중 불분리성 그라우트는 수중 현장에 광범위하게 사용된다. 그러나 접합강도, 펌프 능력 및 강도 손실과 같은 주요 문제점이 여전히 존재한다. 본 연구에서는 자기충전, 비파괴 방지 그라우트 연구에 기초하여 이 분야의 현황을 파악하기 위해 수중 시공 및 카르스트 공동 실링에 관한 연구 동향에 대해 검토하였다. 그라우트를 수중에 사용할 경우, 공기 중에서 시공하는 것에 비해 강도와 접합강도가 손실될 것이다. 이를 방지하기 위해 고점도의 그라우트를 통해 카르스트 공동을 실링하고 있지만, 대심도에서는 그라우트의 펌핑 능력에 심각한 문제를 발생시키므로 기존의 수중 불분리성 그라우트와 콘크리트는 대심도 환경에 적합하지 않음을 의미한다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권3호
• /
• pp.15-20
• /
• 2018

No-insulation (NI) pancake magnets are fabricated using Rare earth-Barium-Copper Oxide (REBCO) coated conductor (CC) tapes, which enabled a very compact magnet in the aspects of high critical current density ($J_c$) and high mechanical strength by removing insulation and allowing thinner stabilizer. They have also advantages such as self-quench protection. Therefore, it does not need quench detection and protection that can be very challenging in a high critical temperature ($T_c$) superconducting magnet technology. Recently, it was reported that the NI REBCO CC magnets have some drawbacks of long charging time and high field ramp loss which will be a concern in the operation of cryocooled magnets. These issues are related to the turn-to-turn contact resistivity and can be released by managing it. This is also closely related to the activity of reducing the contact joint resistance in the case of CC joints for long length CC fabrication. Therefore, in this study, the turn-to-turn contact resistance ($R_c$) at the CC contact part of differently stabilized CC tapes was measured. The behaviors of $R_c$ at CC contact parts according to the applied contact pressure were investigated. The range of $R_c$ measured for CC tapes adopted will provide fundamental data for design and fabrication of the CC NI coils.