• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.7
• /
• pp.573-578
• /
• 2003

Low temperature selective epitaxial growth of Si and SiGe has been obtained using an industrial single wafer chemical vapor deposition module operating at reduced pressure. Epitaxial Si and heteroepitaxial SiGe deposition with Ge content about 20 % has been studied as extrinsic base for self-aligned heterojunction bipolar transistors(HBTs), which helps to reduce the parasitic resistance to obtain higher maximum oscillation frequencies(f$\_$max/). The dependence of Si and SiGe deposition rates on exposed windows and their evolution with the addition of HCl to the gas mixture are investigated. SiH$_2$Cl$_2$ was used as the source of Si SEG(Selective Epitaxial Growth) and GeH$_4$ was added to grow SiGe SEG. The addition of HCl into the gas mixture allows increasing an incubation time even low growth temperature of 675∼725$^{\circ}C$. In addition, the selectivity is enhanced for the SiGe alloy and it was proposed that the incubation time for the polycrystalline deposit on the oxide is increased probably due to GeO formation. On the other hand, when only SiGe SEG(Selective Epitaxial Growth) layer is used for extrinsic base, it shows a higher sheet resistance with Ti-silicide because of Ge segregation to the interface, but in case of Si or Si/SiGe SEG layer, the sheet resistance is decreased up to 70 %.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.10A
• /
• pp.1473-1479
• /
• 2000

This paper presents the performance evaluation of an adaptive QAM scheme under flat and frequency selective fading channels for indoor wireless communication systems. The QAM modulation is combined with differential encoding and the demodulation process is carried out noncoherently. The adaptation is performed by varying the modulation level of QAM, depending upon received signal strength. The adaptation mechanism allows a 2- or 3-bit increase or decrease at a time, if the channel condition is considered to be significantly good or bad. Simulation results show that the average number of bits per symbol (ABPS) for each symbol block transmitted over a flat fading channel is higher than 5.0 and the BER performance is better than 10^-4 for a SNR value higher than 30 dB. For frequency selective fading channels, an oversampling technique in the receiver was employed. The BER performance obtained for frequency selective fading channels is better than 10^-4 with a SNR value of 40 dB and ABPS is found to be approximately 5.5. Therefore, this scheme is very useful in that it provides both very high bandwidth efficiency and acceptable performance with moderate SNR values over flat and frequency selective fading channels. In addition, this scheme provides reduced receiver complexity by way of noncoherent detection.

• Journal of Korean Neurosurgical Society
• /
• v.37 no.5
• /
• pp.350-353
• /
• 2005

Objective: Various methods of treatment for idiopathic cervical dystonia have been tried in the past with unsatisfactory results. The authors report cases of five patients who underwent selective peripheral denervation for spasmodic torticollis. Methods: Between July 2002 and December 2003, 5 patients underwent surgery at St. Mary's Hospital for spasmodic torticollis. Age of the patient at the onset of symptoms ranged from 29 to 56years (mean 43.75years). Selective peripheral denervation(SPD) was performed at 7 to 11 months after the onset of symptoms (mean 8.75 months). A patient was considered to be the candidate for surgery if conservative methods were unsuccessful and symptoms persisted for longer than 7months. In addition, 2patients who refused treatment with botulinum toxin were also enrolled in this study. Results: Although one patient underwent reoperation, all of the five patients' symptoms were improved after the operation. Clinically, patients with retrocollis showed better improvement than laterocollis patients. Conclusion: Although injection of botulinum toxin is the first-choice in treatment modality, when surgery is required, selective peripheral denervation provides good results with minimum side effects.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2022.10a
• /
• pp.15-17
• /
• 2022

In order to minimize surplus parts in ball bearing selective assembly systems, it is necessary to optimize the selection probability by grasping the dimensional distribution of each part. But the use of a complex system causes delays in the production process. In this paper, we propose cluster priority selection algorithm that can quickly and simply determine the selection priority in ball bearing selective assembly system. In addition, we assume the simulated situation with the data collected in the actual ball bearing selective assembly process, and evaluate the incidence of surplus part and runtime by simulating the cluster priority selection algorithm and the exiting algorithm. As a result of the simulation, the cluster priority selection algorithm generated 83.8% less surplus parts, and 39.7% less runtime than the existing algorithm.

• Corrosion Science and Technology
• /
• v.19 no.4
• /
• pp.224-230
• /
• 2020

Stainless steel has excellent corrosion resistance. The drawback is that pitting occurs easily due to the concentration of chloride. In addition, corrosion of socket weld, which is structurally and chemically weaker than the other components of the pipe, occurs rapidly. Since these two phenomena overlap, pinhole leakage occurs frequently in the seawater pipe socket welds made of stainless steel at the power plants. To analyze this specific corrosion, a metallurgical analysis of the stainless steel socket welds, where the actual corrosion occurred during the power plant operation, was performed. The micro-structure and chemical composition of each socket weld were analyzed. In addition, selective corrosion of the specific micro-structure in a mixed dendrite structure comprising γ-austenite (gamma-phase iron) and δ-ferrite (iron at high temperature) was investigated based on the characteristic micro-morphology and chemical composition of the corroded area. Finally, the different corrosion stages and characteristics of socket weld corrosion are summarized.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.69-72
• /
• 2003

This paper presents a traffic control agent that can perform the dynamic resource allocation by controlling traffic flows on a DiffServ network. In addition, this paper presents a router that can support DiffServ on Linux to support selective QoS in IP network environment. To implement a method for selective traffic transmission based on priority on a DiffServ router, this paper changes the queuing discipline in Linux, and presents the traffic control agent so that it can efficiently control routers, efficiently allocates network resources according to service requests, and relocate resources in response to state changes of the network.

• Journal of Food Hygiene and Safety
• /
• v.31 no.3
• /
• pp.222-225
• /
• 2016

In this study, the performance of five selective media for coliform bacteria was evaluated. In total, 83 coliform isolates from ready-to-eat food and 21 reference strains were inoculated in five agar media : Chromocult coliform agar (Merck Millipore), HiCrome coliform agar (Sigma), CHROMagar ECC chromogenic media, Brilliance E. coli/coliform selective agar (OXOID), and endo agar (Merck Millipore). Coliform isolates and reference strains were inoculated on the selective media to test media sensitivity and specificity. The tested media showed the following sensitivities for the isolated strains: Chromocult coliforms agar and HiCrome coliform agar, 94%; Brilliance E. coli/coliform selective agar, 93%; CHROMagar ECC chromogenic media, 92%; and endo agar, 74%. In addition, all media showed 100% specificity, except for endo agar (71%). Moreover Chromocult coliform agar and HICrome coliform agar showed high levels recovery. Taken together, these results identified Chromocult coliform agar and HICrome coliform agar as an effective selective medium for coliforms with higher sensitivity and specificity compared to other media tested in this study.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.4
• /
• pp.43-50
• /
• 2012

Metal-metal oxide (M-M oxide) cermet solar selective coatings with a double cermet layer film structure were deposited on the Al-deposited glass substrate by using a directed current (DC) magnetron sputtering technology. M oxide (CrO and ZrO) was used as the ceramic component in the cermets, and Cr and Zr used as the metallic components. In addition, black Cr (Cr-$Cr_2O_3$ cermet) solar selective coatings were deposited on the Ni-plated Cu substrate by using a electroplating method for comparison. The thermal stability tests were carried out for performance evaluation of solar coatings. Reflectance measurements were used to evaluate both solar absorptance(${\alpha}$) and thermal emittance (${\epsilon}$) of the solar coatings before and after thermal testing by using a spectrometer. Optical properties of optimized cermet solar coatings were ${\alpha}{\simeq}0.94-0.96$ and ${\epsilon}{\simeq}0.1$ ($100^{\circ}C$). The results of thermal stability test of M-M oxide solar coatings showed that the Cr-CrO cermet solar selective coatings were more stable than the Zr-ZrO cermet selective coatings at temperature of both $400^{\circ}C$ in air and $450^{\circ}C$ in vacuum. The black Cr solar selective coatings were degraded in air at temperature of $400^{\circ}C$. The main optical degradation modes of these coatings were diffusion of metal atoms, and oxidation.

• ETRI Journal
• /
• v.25 no.6
• /
• pp.503-509
• /
• 2003

Selective epitaxial growth (SEG) of silicon has attracted considerable attention for its good electrical properties and advantages in building microstructures in high-density devices. However, SEG problems, such as an unclear process window, selectivity loss, and nonuniformity have often made application difficult. In our study, we derived processing diagrams for SEG from thermodynamics on gas-phase reactions so that we could predict the SEG process zone for low pressure chemical vapor deposition. In addition, with the help of both the concept of the effective supersaturation ratio and three kinds of E-beam patterns, we evaluated and controlled selectivity loss and non-uniformity in SEG, which is affected by the loading effect. To optimize the SEG process, we propose two practical methods: One deals with cleaning the wafer, and the other involves inserting dummy active patterns into the wide insulator to prevent the silicon from nucleating.

• ETRI Journal
• /
• v.37 no.1
• /
• pp.43-53
• /
• 2015

In this paper, a selective coefficient updating (SCU) approach at each branch of the per-tone equalization (PTEQ) structure has been applied for insufficient cyclic prefix (CP) length. Because of the high number of adaptive filters and their complex adaption process in the PTEQ structure, SCU has been proposed. Using this method leads to a reduction in the computational complexity, while the performance remains almost unchanged. Moreover, the use of set-membership filtering with variable step size is proposed for a sufficient CP case to increase convergence speed and decrease the average number of calculations. Simulation results show that despite the aforementioned algorithms having similar performance in comparison with conventional algorithms, they are able to reduce the number of calculations necessary. In addition, compensation of both the channel effect and the transmitter/receiver in-phase/quadrature-phase imbalances are achievable by these algorithms.