• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.11
• /
• pp.924-927
• /
• 2017

This paper presents a 6~18 GHz 8-bit true time delay (TTD) circuit. The unit delay circuit is based on m-derived filter with relatively constant group delay. The designed 8-bit TTD is implemented with two single-pole double-throw (SPDT) switches and seven double- pole double-throw (DPDT) switches. The reflection characteristics are improved by using inductors. The designed 8-bit TTD was fabricated using $0.18{\mu}m$ CMOS. The measured delay control range was 250 ps with 1 ps of delay resolution. The measured RMS group delay error was less than 11 ps at 6~18 GHz. The measured input/output return losses are better than 10 dB. The chip consumes zero power at 1.8 V supply. The chip size is $2.36{\times}1.04mm^2$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.8
• /
• pp.52-58
• /
• 2008

Ths paper describes the Dual-band switch which was proposed new structure that could improved the specification of broadband and designed by the optimized structure through simulation. The Dual-band switch with 2.4[GHz]/5.8[GHz] that can apply to 802.11a/b/g system that is commercialized present was studied to get a new structure with higher power, high isolation. The transmitter of switch was designed to operate a parallel switching element with stack structure of two FET. The receiver designed to have asymmetry structure that insert series FET in addition to basic serial/parallel FET. SPDT(Single Pole Double Throw) Tx/Rx FET switch is a device that can do switching from a port of input to two port of output. The fabricated SPDT switch has the characteristic of insertion loss of a below -3[dB] form DC to 6[GHz] and the isolation of a below -30D[dB](Rx mode).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1003-1009
• /
• 2005

In this paper, small-size high-power single pole double throw(SPDT) switch with defected pound structure(DGS) is presented for wireless broadband internet application. To reduce the circuit size using slow-wave characteristic, the DGS is applied to ${\lambda}/4$ transmission line of the switch and the measured results are compared with them of conventional switch. To secure high degree of isolation, the switch with the DGS is composed of shunt-connected PIN diodes and shows insertion loss of 0.8 dB and isolation more than 50 dB at 2.3 GHz. The size of the switch is reduced about $50\%$ only with the DGS patterns while it has very similar performance to the conventional shunt-type switch.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.155-159
• /
• 2004

This paper describes the design and the simulation of a single pole double throw(SPDT) FET switch for wireless LAN(IEEE802.11a ＆ IEEE802.11b) applications using drain impedance transformation network with Microstrip transmission line. At the receiving path insertion losses were from 0.8(㏈) to 1.462(㏈) between 2(㎓) and 4(㎓), from l.26(㏈) to 2.3(㏈) between 4.7(㎓) and 6.7(㎓) and the isolations were under 30(㏈) between 2(㎓) and 6.7(㎓). At the transmitting path insertion loss were from 1.18(㏈) to 2.87(㏈) between 2(㎓) and 4(㎓) from 0.625(㏈) to 1.2(㏈) between 4.7(㎓) and 6.7(㎓) and the isolations were under 30(㏈) between 2(㎓) and 6.7(㎓).

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.1 s.343
• /
• pp.143-148
• /
• 2006

This paper presents a high isolation and power-handling single-pole double-throw(SPDT) switch for dual band wireless LAN applications. The switch circuit has asymmetric topology which uses stacked-gate to have high power-handling and isolation for the Tx path. The proposed SPDT switch has been designed with optimum gate-width, bias, and number of stacked-gate FET. This SPDT switch has been implemented with $0.25{\mu}m$ GaAs pHEMT process which has Gmmax of 500mS/mm and fmax of 150GHz. The designed SPDT switch has the measured insertion loss of better than 0.9dB and isolation of better than 40dB for the Tx path and 25dB for the Rx path and the high power handling capability with PldB of about 23dBm for control voltage of -3/0V. The fabricated SPDT switch chip size is $1.8mm{\times}1.8mm$.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.22 no.6
• /
• pp.223-229
• /
• 2023

This papart proposes single pole double throw (SPDT) switch with six-stage radial stub resonators in the 3.6~4.0 GHz band. The switch was simulated using ADS (Advanced Design Software), a design tool for the wireless communication circuits, and evaluated on a pcb substrate. The measurement results of the radial SPDT switch showed an average 90 dB isolation, and 1.5 dB insertion loss. This isolation characteristic was 20 dB superior to higher than those laboratory or commercial products reported thus far. The proposed SPDT switch is applicable to multi-band RF front-end systems, such as WiMAX, LTE/5G, Wi-Fi, and HyperLAN.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.411-414
• /
• 2014

A switch is one of the most useful circuits for controlling the path of signal transmission. It can be added to digital circuits to create a kind of gate-level device and it can also save information into memory. In RF subsystems, a switch is used in a different way than its general role in digital circuits. The most important characteristic to consider when designing an RF switch is keeping the isolation as high as possible while also keeping insertion loss as low as possible. For high isolation, we propose leakage signal cancellation and inductive switching for designing a singlepole double-throw (SPDT) RF switch. By using the proposed method, an isolation level of more than 23 dB can be achieved. Furthermore, the heterojunction bipolar transistor (HBT) process is used in the RF switch design to keep the insertion loss low. It is demonstrated that the proposed RF switch has an insertion loss of less than 2 dB. The RF switch operates from 1 to 8 GHz based on the $0.18-{\mu}m$ SiGe HBT process, taking up an area of $0.3mm^2$.

• IEIE Transactions on Smart Processing and Computing
• /
• v.5 no.3
• /
• pp.164-168
• /
• 2016

A low insertion-loss, high-isolation switch based on single pole double throw (SPDT) for a 2.4GHz Bluetooth low-energy transceiver is presented in this paper. In order to increase isolation, the body floating technique is implemented. Based on characteristics whereby the ratio of the sizes of the shunt and the series transistors significantly affect the performance of the switches, the device sizes are optimized. A simple matching network is also designed to enhance the insertion loss. Thus, the SPDT switch has high isolation and low insertion loss without increasing the complexity of the circuit. The proposed SPDT is designed and simulated in a complementary metal-oxide semiconductor 65nm process. The switch has a $530{\mu}m{\times}270{\mu}m$ area and achieves 0.9dB, 1.78dB insertion loss and 40dB, 41dB isolation of transmission, reception modes, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.833-839
• /
• 2011

This paper has suggested a technique for measuring VSWR at 1.8 GHz band for various modulated signals. By using directional coupler the power of incident and reflected wave is measured, and in order to minimize the size and cost of the measuring circuit, a SPDT(Single Pole Double Throw) switch is adopted to realize the circuit with just one detector and one A/D(Analog to Digital) converter. MCU(Micro Control Unit) is used to calculate the voltage reflection coefficient and VSWR, and the measured VSWR error has improved by approximately 0.2 with applying a simple bubble sorting algorithm to reduce the measurement error, the MCU process time and load.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.422-423
• /
• 2005

RF Micro switches is a miniature device or an array of integration devices and mechanical components and fabricated with Ie batch-processing techniques. RF Micro switches application area are in phased arrays and reconfigurable apertures for defence and telecommunication systems, switching network for satellite communication, and single-pole double throw switches for wireless application. Recently, RF Micro switches have been developed for the application to the milimeter wave system. RF Micro switches offer a substantilly higher performance than PIN diode or FET switches. In this paper, SPDT(single-pole-double-throw) switch are designed to use 10 GHz. Actuation voltage and displacement are simulated by tool.