• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2008

A dynamic model for II-SEPIC(Isolated Inverse-SEPIC) is developed based on the state-space averaging method and its control characteristics are investigated in this paper. Equations for circuit design of II-SEPIC are derived through steady state analysis and the resulted circuit parameters are used in the consequent simulation and experiment works. A structure of control system is devised to obtain better control performance. In order to verify validity and effectiveness of the design equations and dynamic model derived, dynamic control responses of II-SEPIC system against line and load variation are illustrated in both simulation and experiment.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.26-28
• /
• 2007

Design equations of II-SEPIC (Isolated Inverse-SEPIC) are derived and its dynamic model is also made using state-space averaging method in this paper. II-SEPIC is comprehensively investigated through the frequency response analysis, compared with those of I-SEPIC (Isolated SEPIC).

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.447-454
• /
• 2016

A single-ended primary-inductor converter (SEPIC) features low input current ripple and output voltage up/down capability. However, the switching devices in a two-level SEPIC suffer from high voltage stresses and switching losses. To cope with this drawback, this study proposes a three-level SEPIC that uses a low voltage-rated switch and thus achieves better switching performance compared with the two-level SEPIC. The three-level SEPIC can reduce switch voltage stresses and switching losses. The converter operation and control method are described in this work. The experimental results for a 500 W prototype converter are also discussed. Experimental results show that unlike the two-level SEPIC, the three-level SEPIC achieves improved power efficiency with balanced capacitor voltages.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.4
• /
• pp.20-25
• /
• 2003

This paper presents the PFC method for an electronic ballast using SEPIC converter. Generally, the Boost Converter Type PFC has a DC 400V and output voltage is a bigger than input rms voltage. But the SEPIC type converter has above 0.95 Power Factor and wanted output voltage. This paper employs the SEPIC(Single Ended Primary Inductance Converter) Converter for PFC and the Ring core for oscillating method. Consequently, We reduced element's size and capacity in a converter with minimum voltage for the operating lamp.

• Proceedings of the IEEK Conference
• /
• 2001.06e
• /
• pp.107-110
• /
• 2001

The capacitive idling SEPIC(Single Ended primary Inductance Converter) is derived from the SEPIC topology. This converter is suitable for maximizing Li-Ion battery life in portable equipments. Besides, that makes it possible to increase the switching frequency without a additional circuitry This paper is presented the characteristics of the capacitive idling SEPIC and experimental waveforms of the devices in continuous current mode.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.330-334
• /
• 2004

A new SEPIC-Flyback converter is proposed. The proposed converter is the integration of SEPIC and Flyback converter. Not only SEPIC output but also Flyback output could be fully regulated by constant frequency PWM control. Merged SEPIC and Flyback topology can share the transformer and power MOSFET. When the switch turns on, one topology operates via capacitive energy transfer. The other topology acts as inductive energy transfer while the switch is off. So, it can increase power density per one cycle. The experimental result is presented and verified.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.526-529
• /
• 2004

A new SEPIC-Flyback convater is proposed. The proposed converter is the superposition of SEPIC and Flyback converter. Not only SEPIC output but also Flyback output could be fully regulated by constant frequency PWM control. Merged SEPIC and Flyback topology could share the transformer and power MOSFET. When the switch turns of one topology operates via capacitive energy transfer. Another topology acts as powering mode while the switch is off. So, it could increase power falsify per one cycle. The operating principle of the proposed converter is described below. Prototype featuring 24V input 48V output, 100kHz switching frequency, and 100W output is simulated under the proposed topology.

• Journal of Power Electronics
• /
• v.9 no.1
• /
• pp.26-35
• /
• 2009

A high efficiency active clamp sepic-flyback converter is presented for fuel cell generation systems. The proposed converter is a superposition of a sepic converter mode and. flyback converter mode. The output voltages of the sepic converter mode and flyback converter mode can be regulated by the same PWM technique with constant frequency. By merging the sepic and flyback topologies, they can share the transformer, power MOSFET and active clamp circuit. The result has outstanding advantages over conventional active clamp DC-DC converters: high efficiency, high power density, and component utilization. Simulation results and experimental results are presented to verify the principles of operation for the proposed converter.

• Journal of Power Electronics
• /
• v.14 no.4
• /
• pp.649-660
• /
• 2014

A novel non-isolated bidirectional soft-switching SEPIC/ZETA converter with reduced ripple currents is proposed and characterized in this study. Two auxiliary switches and an inductor are added to the original bidirectional SEPIC/ZETA components to form a new direct power delivery path between input and output. The proposed converter can be operated in the forward SEPIC and reverse ZETA modes with reduced ripple currents and increased voltage gains attributed to the optimized selection of duty ratios. All switches in the proposed converter can be operated at zero-current-switching turn-on and/or turn-off through soft current commutation. Therefore, the switching and conduction losses of the proposed converter are considerably reduced compared with those of conventional bidirectional SEPIC/ZETA converters. The operation principles and characteristics of the proposed converter are analyzed in detail and verified by the simulation and experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.3
• /
• pp.285-293
• /
• 2004

In this Paper the electronic ballast using the SEPIC(Single Ended Primary Inductor Converter) converter for the multiple electrodeless fluorescent lamps is proposed, which has the structure of the active PFC and self oscillating function. The SEPIC converter system has the characteristics of the power factor with low input current harmonic distortion. The proposed control method is based on the aveage-current-mode using the dedicated integrated circuit UC3854. The proposed electronic ballast has the reduction effect for the energy and manufacturing cost because it is designed for tripple electrodeless fluorescent lamps. The experimental results shows that the power factor is higher and the THD is lower.