• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.5
• /
• pp.17-26
• /
• 2021

It is challenging to estimate the fatigue life of construction equipment consisting of a welded joint using field structure test owing to the uncertainty of the S-N curve. IIW recommends different S-N curves for various welded joint types. However, there is no way to define an appropriate curve considering complex design shape and strain gauge characteristics. This paper proposes an equivalent S-N curve method based on the relationship between IIW effective notch stress and virtual stress using finite element analysis. Moreover, a case study was conducted for the excavator fuel tank. The proposed method is expected to enhance accuracy and consistency in calculating the fatigue life for the welded structure of construction equipment.

• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.117-126
• /
• 2012

Understanding driver's characteristic of visual activity is important process because driver depends on a visual signal more than 90% for getting outside information needed to drive, thus a series of driving, including perception, judgement, and activity, is completed. This study analyzes quantified driver's sight range in curved section where recognition of various information is critical due to biggest speed change among sections. Simulation is utilized for this study because of safety problem on field experiment and difficulties in using equipment. Building 6 roads that have different in curve radius by virtual driving map, experiment is carried out recruiting 30 people. Through analytical researches, it shows that drivers keep an eye on direction of driving, and driver's visual range is narrowed on left curve than right curve, and the more curve radius become small, the more drivers see in narrow angle.

• Journal of Korea Water Resources Association
• /
• v.36 no.2
• /
• pp.211-221
• /
• 2003

The objectives of this study are to analyze the effects of time-area curve on Clark's watershed runoff method in addition to propose a GIS-based objective method for creating time-area curve. For the relative comparison of the variation of time-area curve to those of travel time and storage coefficient of Clark method, runoff sensitivities are performed on Soyang- and Chungju-dam watersheds for 1990. 9. 10~9. 14 event. The dimensionless time-area curve in HEC-1 that can be utilized in the case that the curve is not supplied is also tested in this study. The important results obtained in this study are as follows: The effects of time-area curve created by either GIS-based objective method or dimensionless curve are not significant for runoff analysis; The storage coefficient (K) and travel time( t$_{c}$), Clark's other two model parameters, are more sensitive than time-area curve for peak flow simulation. Therefore, it can be concluded that the parameters K and t$_{c}$ are more carefully estimated rather than time-area curve, when Clark method is used for runoff analysis.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.11
• /
• pp.31-42
• /
• 2016

Usually the seismic stability analysis of slope uses the pseudostatic analysis considering the inertial force by the earthquake as a static load. Geostructures such as slope include the uncertainty of soil properties. Therefore, it is necessary to consider probabilistic method for stability analysis. In this study, the probabilistic stability analysis of slope considering the uncertainty of soil properties has been performed. The fragility curve that represents the probability of exceeding limit state of slope as a function of the ground motion has been established. The Monte Carlo Simulation (MCS) has been implemented to perform the probabilistic stability analysis of slope with pseudostatic analysis. A procedure to develop the fragility curve by the pseudostatic horizontal acceleration has been presented by calculating the probability of failure based on the Artificial Neural Network (ANN) based response surface technique that reduces the required time of MCS. The results showed that the proposed method can get the fragility curve that is similar to the direct MCS-based fragility curve, and can be efficiently used to reduce the analysis time.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.05a
• /
• pp.148-151
• /
• 2004

Mechanical properties such as Young's modulus and hardness of thin film in coated steel are difficult to determine by nano-indentation from the conventional analysis using the load-displacement curve. Therefore, an analysis of the nano-indentation loading curve was used to determine the Young's modulus, hardness and strain hardening exponent. A new method is recently being developed for plasticity properties of materials from nano-indentation. Elastic modulus of the thin films shows relatively small influence whereas yield strength and strain hardening are found to have significant effect on measured data. The load-displacement behavior of material tested with a Berkovich indenter and nano-indentation continuous stiffness method is used to measure the modulus and hardness through thin films.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.830-835
• /
• 2012

A research for application of LDSMC(Low Density Sheet Molding Compound) composite is in progress for lightening the weight. This paper has performed fatigue test and simulation of external panel for Korean commercial vehicle. Before the fatigue test, static test was carried out. From the test, the structural safety was investigated using Goodman diagram. After the static test performance, the fatigue test was conducted at a range of load frequency 5Hz, a stress ratio(R) of 0.05 and an endurance limit of $10^6$ to obtain the S-N curve. The S-N curve is applied to the fatigue analysis of the external panel assembly. The result of FEM analysis was in accord with the experimental result within 83% confidence. It showed that the process to set up the safety range of allowable error is required in process of the design and simulation verification.

• Journal of Food Hygiene and Safety
• /
• v.23 no.2
• /
• pp.121-128
• /
• 2008

The aim of this study was to develop a LightCycler-based real time PCR (LC-PCR) assay and to evaluate its diagnostic use for the detection of Staphylococcus aureus in raw milk samples. Following amplification of 113 bp of coa gene encoding an coagulase precursor specific for Staphylococcus aureus, melting curve and DNA sequencing analysis was performed to verify the specificity of the PCR products. Amplification of 209 bp gene encoding an altered penicillin-binding protein, PBP2a (mecA), melting curve analysis and DNA sequencing analysis was performed to verify methicillin resistance Staphylococcus aureus (MRSA). According to this study, 6 of 647 raw milk samples showed S. aureus positive and 2 of them showed a mecA positive and the detection limit was 10 fg of DNA. And we also isolated Staphylococcus chromogenes a causative agent of exudative epidermitis in pigs and cattle from 3 samples.

• Explosives and Blasting
• /
• v.24 no.1
• /
• pp.9-19
• /
• 2006

The objective of this study is to propose curve fitted equations that can facilitate calculations and improve a practical applicability when the seismic performance of buried pipelines needs to be evaluated. The curve fitted equations are derived based on the evaluation of the dynamic responses of concrete pipe with a boundary condition of fixed-free ends. To study the dynamic response of underground pipe, the numerical analysis program developed in the previous research has been used. The location of maximum strain has been determined through dynamic analyses for a boundary condition of fixed-free ends. Then $wavelength{\lambda}$ of 5-1000(m) and propagation velocity(Vs) of 100-2000(m/s) have been applied at the location of maximum strain and the unit srain curve with the changes of the $wavelength{\lambda}$ and propagation velocity(Vs) has been obtaind. Non-linear least-square regression has been used to develop highly applicable curve fitted equations and various types of exponential regression equations have been checked out. Thus curve fitted equations and necessary coefficients with best results are suggested.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.920-924
• /
• 2002

This paper presents the reverse design of a cam mechanism using NURBS(Nonuniform Rational B-spline curve). Cam is very difficult to make the accurate shape on the design and the manufacture. Because the cam shape is commonly made in order to move in special functions. The reverse design can be used to check accuracy between the designed data and the manufactured data of the cam shape and also reproduce the cam without the design data. The reverse design procedures consist of motion analysis and curve fitting. The motion analysis is used the central difference method and the relative velocity method to find the displacement and velocity. The curve fitting is used NURBS to develope the whole curve. The central difference method is derived in the 3 dimensional space.

• Communications for Statistical Applications and Methods
• /
• v.26 no.2
• /
• pp.79-89
• /
• 2019

Classification models pertaining to receiver operating characteristic (ROC) curve analysis have been extended from univariate to multivariate setup by linearly combining available multiple markers. One such classification model is the multivariate ROC curve analysis. However, not all markers contribute in a real scenario and may mask the contribution of other markers in classifying the individuals/objects. This paper addresses this issue by developing an algorithm that helps in identifying the important markers that are significant and true contributors. The proposed variable selection framework is supported by real datasets and a simulation study, it is shown to provide insight about the individual marker's significance in providing a classifier rule/linear combination with good extent of classification.