• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.65-66
• /
• 2006

Dancer systems are most widely used mechanism for attenuation of tension disturbances. Lately, demands fur high speed converting machines over 500mpm(m/min) are raising but domestic converting industries can not come up with the machines because capacities for a designing of the converting machine are restricted lower than 300mpm. Moreover roll-to-roll is attracted flexible display manufacturer's attention as a effective method for productivity. A constant tension level in the span before the first printing cylinder is the key of high speed quality printing. This paper presents a modeling and simulations of dancer systems on converting machines.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.15-24
• /
• 2014

Recently, a variety of printing technologies, including ink jet, gravure, and roll-to-roll (R2R) printing, has generated intensive interest in the application of flexible and wearable electronic devices. However, the actual use of printing technique is much limited because the sintering process of the printed nanoparticle inks remains as a huge practical drawback. In the fabrication of the conductive metal film, a post-sintering process is required to achieve high conductivity of the printed film. The conventional thermal sintering takes considerable sintering times, and requires high temperatures. For application to flexible devices, the sintering temperature should be as low as possible to minimize the damage of polymer substrate. Several alternative sintering methods were suggested, such as laser, halogen lamp, infrared, plasma, ohmic, microwave, and etc. Eventually, the new sintering technique should be applicable to large area, R2R, and polymer substrate as well as low cost. This article reviews progress in recent technologies for several sintering methods. The advantages and disadvantages of each technology will be reviewed. Several issues for the application in R2R process are discussed.

• Laser Solutions
• /
• v.3 no.2
• /
• pp.35-43
• /
• 2000

Laser direct patterning of the coated photoresit (PMER-NSG31B) layer was studied to make halftone dots on gravure printing roll. The selective laser hardening of photoresist by Ar-ion laser(wavelength : 333.6nm∼363.8nm) was controlled by the A/O modulator. The coating thickness in the range of 5㎛∼11㎛ could be obtained by using the up-down directional moving device along the vertically located roll. The width, thickness and hardness of the hardened lines formed under laser power of 200∼260㎽ and irradiation time of 4.4∼6.6$\mu$ sec/point were investigated after developing. The hardened width increased according to the increase of coating thickness. Though the hardened thickness was changed due to the effect of the developing solution, the hardened layer showed good resistance to the scratching of 2H pencil. Also, the hardened minimum line widths of 10㎛ could be obtained. The change of line width was also found after etching, and the minimum line widths of 6㎛ could be obtained. The hardened lines showed the good resistance to the etching solution. Finally, the experimental data could be applied to make gravure halftone dots using the developed imaging process, successfully.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.5
• /
• pp.96-102
• /
• 2008

Manufacturing of printed electronics using printing technology has begun to get into the hot issue in many ways due to the low cost effectiveness to existing semi-conductor process. This technology, with low cost and high productivity, can make it possible to produce printed electronics such as TFT, solar cell, RFID Tag, printed battery, and so on. In this study, apparatus of gravure-offset printing are developed for fine line-width/gap printing and the results obtained from the apparatus shows that it is possible to make around 20 micro-meter line-width/gap printing patterns. The roll-to-roll printing system for fine line-width printing based on primary experiment is presented. The printing results obtained from the system shows around 30 micro-meter line-width/gap printing patterns.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.3
• /
• pp.95-103
• /
• 2010

Roll to Roll (R2R) is one of the most promising production technologies in the printed electronics such as OLEDs, e-paper, backplanes, RFID because this technology can save production cost and increase production speed. Printed electronics includes various processes such as printing, drying, winding, unwinding, and so on. In printed electronics R2R system, air-flotation oven is employed for drying process. Therefore, it is essential to introduce efficient and fast drying process when printing is finished. This paper considers the analysis of drying process in R2R that involves hot air flow. Air-flotation oven consists of non-contact supports and drying of coated web materials such as plastic films and paper. In this paper, experimental results and numerical analysis of pressure-pad air bar are investigated. The aerodynamic characteristics of pressure-pad air bar are numerically calculated using computational fluid dynamics (CFD) approach. Then the measured values of the aerodynamic forces for air bars are compared with those of CFD analysis.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.8
• /
• pp.792-797
• /
• 2009

This paper presents the evaluation of PID and fuzzy control logic for the lateral position control of a moving web in roll-to-roll (R2R) printed electronics. In addition, we report the implementation of computer simulation software that enables us to develop the control logic in a graphic user interface and to test the controller performance in 3D dynamic environment. A mathematical model of the web dynamics is described first to explain the lateral motion of a moving web. Based on the model, PID and fuzzy controllers are designed, and embedded in the simulation software. Under the simulation conditions for fabricating RFID antenna by R2R printing, the results indicate that the fuzzy controller shows a better performance and can be more suitable for R2R multi-layer printed electronics.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.2
• /
• pp.263-272
• /
• 2013

Printed electronics creates electrically functional devices by printing on variety of substrates. Printing typically uses common printing equipment or other low-cost equipment suitable for defining patterns on material, such as screen printing, flexography, gravure, offset lithography and inkjet. Compared to conventional manufacturing of microelectronics, printed electronics is characterized by simpler and more cost-effective fabrication of high and low volume products. Now there is huge effort towards printing many other more functional components, from displays to transistors to photovoltaic cells, using the full range of printing technologies - from inkjet to roll to roll analogue print techniques. The market for printed electronics will rise from $1.99 billion in 2010 to $55.10 billion in 2020. In 2030, this industry could be $300 billion - larger than the silicon semiconductor industry - from lighting to displays[8].

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1153-1158
• /
• 2011

Roll-to-roll process is an emerging mass production method for printed and flexible electronics such as touch screen panel, RFID tag, thin film solar cell, and flexible display due to its high throughput. High precision in printing and coating is required to apply functional materials onto substrate. For such reason, every part of the roll-to-roll equipment needs to be precisely fabricated and to retain its precision under regular operation. In this article, the precision of cantilever type idler roller and a novel method to mitigate its deflection under web tension loading are discussed and the method is verified using both the numerical and the experimental works. The proposed method improves the structural rigidity of cantilever type roller whose advantages, such as low capital cost and high web path configurability, are maintained.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.9
• /
• pp.16-19
• /
• 2010

This paper presents how to design and fabricate the gravure offset printing system for enhancement of register precision. Factors of precision error are caused by imprecision of gravure plate, deformation of substrate, printing quality change due to the change of ink viscosity, Imprecision of printing machine, and so on. This study suggests concept design of gravure offset printing system which is able to minimize or remove these error factors.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.6
• /
• pp.462-467
• /
• 2013

In this paper, we analyzed the effects of doctoring process on the patterns of Ag ink in gravure off-set printing. The parameters of doctoring process were the angle and the pressure, which was represented by the depth of blade movement to the gravure roll, of doctor blade to the surface of gravure roll, and the angle of patterns engraved on the gravure roll to the doctor blade moving direction. The proper parameters were extracted for the fine patterns and they were 15 mm for the pressure, $60^{\circ}$ for the blade angle. And the angle of patterns with respect to the blade movement should be less than $40^{\circ}$ for the best results. The gravure off-set printing with the above parameters was carried out to print gate electrodes and scan bus lines of OTFT-backplane for e-paper. The line width of $50{\mu}m$ was successfully obtained. The thickness of electrodes was $2.5{\mu}m$ and the surface roughness was $0.65{\mu}m$ and the sheet resistance was $15.8{\Omega}/{\Box}$.